2011-2016 FJ Cruiser · Service Manual DRIVE LINE

INSTALLATION

Removal / installation · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009


1. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

C093595E01
  1. Install a new bearing spacer.

    HINT:
    Install the spacer in the correct direction.


2. INSTALL DIFFERENTIAL OIL STORAGE RING
  1. Using a brass bar and hammer, tap in a new oil storage ring.

    NOTICE:
    Be careful not to damage the oil storage ring.


3. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

G021735E01
  1. Using SST and hammer, tap in the roller bearing (outer).

    SST
    09316-60011   (09316-00011, 09316-00021)

  1. Install the roller bearing (inner).


4. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

5. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

F040719E03
  1. Apply MP grease to the lip of a new oil seal.

  1. Using SST and hammer, tap in the oil seal.

    SST
    09554-30011  

    Oil seal depth:
    0.55 to 1.45 mm (0.021 to 0.057 in.)


6. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

F040716E01
  1. Using SST, install the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.

  1. B087843E01
    Using SST to hold the companion flange in place, install the nut.
    SST
    09330-00021   (09330-00030)

    Torque:
    370 N*m{ 3,770 kgf*cm , 273 ft.*lbf } or less


7. INSTALL DIFFERENTIAL DRIVE PINION PRELOAD

C089308E01
  1. Using a torque wrench, measure the preload.

    Preload (at starting):
    Item
    Specified Condition
    New bearing
    1.05 to 1.64 N*m (11 to 17 kgf*cm, 9.3 to 15 in.*lbf)
    Reused bearing
    0.56 to 0.85 N*m (6 to 9 kgf*cm, 4.9 to 7.5 in.*lbf)

    If the result is not as specified, adjust the preload.


8. STAKE DRIVE PINION NUT

C089310E01
  1. Using a chisel and hammer, stake the nut.


9. INSTALL REAR PROPELLER SHAFT ASSEMBLY

C098700E02
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }

  1. C098699E02
    Align the matchmarks on the propeller shaft flange and transfer flange.

  1. Install the propeller shaft assembly with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }


10. ADD DIFFERENTIAL OIL

D025304E05
  1. Stop the vehicle on a level surface.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. After changing the oil seal, drive the vehicle and then check the oil level again.
    1. Too much or too little oil will lead to differential problems.

    HINT:
    If necessary, fill the differential carrier assembly with hypoid gear oil.


    Front Differential:
    Item
    Temperature
    Oil grade
    Viscosity
    Capacity
    w/ A.D.D.
    -
    Hypoid gear oil API GL-4 or GL-5
    SAE 75W-90
    1.45 to 1.55 liters
    (1.53 to 1.63 US qts, 1.27 to 1.36 Imp. qts.)
    w/o A.D.D.
    Above -18 °C (-0.4 °F)
    SAE 90
    1.35 to 1.45 liters
    (1.42 to 1.53 US qts, 1.18 to 1.27 Imp. qts.)
    Below -18 °C (-0.4 °F)
    SAE 85W-90


    Rear Differential:
    Item
    Temperature
    Oil grade
    Viscosity
    Capacity
    w/o Differential lock
    Above -18 °C (-0.4 °F)
    Hypoid gear oil API GL-5
    SAE 90
    2.95 to 3.05 liters
    (3.12 to 3.22 US qts, 2.60 to 2.68 Imp. qts.)
    Below -18 °C (-0.4 °F)
    SAE 85W-90
    w/ Differential lock
    Above -18 °C (-0.4 °F)
    SAE 90
    2.85 to 2.95 liters
    (3.01 to 3.12 US qts, 2.51 to 2.60 Imp. qts.)
    Below -18 °C (-0.4 °F)
    SAE 85W-90

  1. Check for oil leakage when the oil level is low.

  1. Install the differential filler plug with a new gasket.

    Torque:
    Front differential:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }
    Rear differential:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


11. CHECK FOR DIFFERENTIAL OIL LEAKAGE
← REMOVAL (from Aug 2009)INSTALLATION (from Aug 2009) →