INSTALLATION
Removal / installation · Vehicles built Jul 2007 – Oct 2010
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012
| 1.
INSTALL REAR COMBINATION LIGHT ASSEMBLY |
 |
Connect the 3 connectors and install the rear combination light.
Install the 3 nuts.
-
Torque:
- 6.0 N*m{
61 kgf*cm
, 53 in.*lbf
}
| 2.
INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
|
 |
- Engage the 6 clips and the 8 claws and install the deck trim side panel.
- Tighten the 3 screws.
Tighten the bolt.
-
Torque:
- 5.5 N*m{
56 kgf*cm
, 49 in.*lbf
}
| 3.
INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
|
 |
- Engage the 6 clips and the 8 claws and install the deck trim side panel.
- Tighten the 3 screws.
| 4.
INSTALL REAR SEAT OUTER BELT ASSEMBLY RH
|
 |
- Install the anchor plate with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
Make sure that the anchor plate rotates smoothly.
| 5.
INSTALL REAR SEAT OUTER BELT ASSEMBLY LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 6.
INSTALL LAP BELT OUTER ANCHOR COVER
|
 |
- Engage the 3 claws and install the lap belt outer anchor cover.
| 7.
INSTALL AMPLIFIER BOX SPEAKER ASSEMBLY (w/ Woofer)
|
 |
- Install the amplifier box speaker with the 4 screws.
-
Torque:
- 8.1 N*m{
85 kgf*cm
, 72 in.*lbf
}
Connect the speaker connector.
| 8.
INSTALL SPEAKER MOUNTING COVER (w/ Woofer)
|
 |
- Engage the 8 clips and install the speaker mounting cover.
| 9.
INSTALL DECK SIDE GARNISH (w/ Woofer)
|
 |
- Engage the 6 claws and install the deck side garnish.
| 10.
INSTALL QUARTER TRIM POCKET (w/o Woofer)
|
 |
- Engage the 6 claws and install the quarter trim pocket.
| 11.
INSTALL SIDE TRIM COVER (w/o Woofer)
|
 |
- Engage the 8 claws and install the side trim cover.
| 12.
INSTALL QUARTER TRIM POCKET TRAY (w/o Woofer)
|
 |
- Engage the 7 claws and install the quarter trim pocket tray.
| 13.
INSTALL PACKAGE HOLDER NET HOOK
|
 |
- HINT:
- Use the same procedure to install all the package holder net hooks.
Install the package holder net hook with the bolt.
-
Torque:
- 8.1 N*m{
83 kgf*cm
, 72 in.*lbf
}
| 14.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
|
 |
- Align the locating marks with the paint marks first, and install the front door opening trim weatherstrip, as shown in the illustration.
- Paint mark:
Area
|
Color
|
RH side
|
White
|
LH side
|
Red
|
| 15.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 16.
INSTALL REAR DOOR SCUFF PLATE RH
|
 |
- Engage the 6 claws and install the access door scuff plate.
| 17.
INSTALL REAR DOOR SCUFF PLATE LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 18.
INSTALL FRONT DOOR SCUFF PLATE RH
|
 |
- Engage the 14 claws and install the door scuff plate.
| 19.
INSTALL FRONT DOOR SCUFF PLATE LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 20.
INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY
|
 |
- HINT:
- Use the same procedure for both sides.
Install the luggage hold belt striker with the bolt.
-
Torque:
- 18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
Install the cap.
| 21.
INSTALL REAR FLOOR MAT ASSEMBLY
|
 |
- Install the rear floor mat with the 2 clips.
| 22.
INSTALL REAR FLOOR MAT SUPPORT PLATE
|
 |
- Engage the 11 claws and install the rear floor mat support plate.
- Tighten the 5 screws.
| 23.
INSTALL REAR FLOOR BOARD
|
 |
- Engage the clip and claw and install the rear floor board.
- Install the luggage hold belt striker with the bolt.
-
Torque:
- 18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
- HINT:
- Use the same procedure for both sides.
| 24.
INSTALL REAR SEATBACK ASSEMBLY RH
|
 |
- Engage the hook and temporarily install the rear seatback with the 2 bolts.
Tighten the 2 bolts in the sequence shown in the illustration.
-
Torque:
- 37 N*m{
375 kgf*cm
, 27 ft.*lbf
}
Pull up the rear seatback.
- Install the rear seat inner belt into the rear seatback holder.
Install the anchor plate of the rear center seat outer belt with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- Do not place the anchor plate over the convex area of the rear seat inner belt.
| 25.
INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH
|
 |
- Pull the rear seatback lock release button and tilt the rear seatback forward.
Engage the 10 clips and install the rear seatback board carpet.
Pull up the rear seatback.
| 26.
INSTALL REAR SEATBACK ASSEMBLY LH
|
 |
- Engage the hook and temporarily install the rear seatback with the 2 bolts.
Tighten the 2 bolts in the sequence shown in the illustration.
-
Torque:
- 37 N*m{
375 kgf*cm
, 27 ft.*lbf
}
Install the rear center seat inner belt into the rear seatback holder.
| 27.
INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH
|
 |
- Engage the 8 clips and install the rear seatback board carpet.
Pull up the rear seatback.
| 28.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
 |
-
Torque:
- 3.9 N*m{
40 kgf*cm
, 35 in.*lbf
}