Wiper and Washer Switch Circuit
Circuit diagnosis · Vehicles built from Jul 2007
DESCRIPTION
The manual operation signals are sent to the main body ECU.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK VEHICLE CONDITION |
Check whether the rear wiper and washer systems operate normally.
- Result:
Condition
Proceed to
Rear wiper and washer systems do not operate.
A
Rear wiper system does not operate.
B
Rear washer system does not operate.
C
|
|
||||
|
|
||||
| A | |
| 2. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY |
![]() ![]() |
Remove the windshield wiper switch assembly.
Inspect the rear wiper switch.
Measure the resistance.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
2 (E) - 13 (C1R) - 10 (+1R)
OFF
10 kΩ or higher
2 (E) - 13 (C1R)
LO
Below 1 Ω
2 (E) - 10 (+1R)
HI
Below 1 Ω
Inspect the rear washer switch.
Measure the resistance.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
2 (E) - 10 (+1R) - 12 (WR)
OFF
10 kΩ or higher
2 (E) - 12 (WR)
ON (Rear wiper switch in OFF position)
Below 1 Ω
2 (E) - 10 (+1R) - 12 (WR)
ON (Rear wiper switch in ON position)
Below 1 Ω
Reinstall the the windshield wiper switch assembly.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - BODY GROUND) |
Disconnect the E19 windshield wiper switch connector.

Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E19-2 - Body ground
Always
Below 1 Ω
Reconnect the windshield wiper switch connector.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (BATTERY - MAIN BODY ECU) |
Measure the voltage.

- Standard voltage:
Tester Connection
Condition
Specified Condition
1C-2 (SIG) - Body ground
Ignition switch OFF
Below 1 V
1C-2 (SIG) - Body ground
Ignition switch ON
11 to 14 V
|
|
||||
| OK | ||
| ||
| 5. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY |
![]() ![]() |
Remove the windshield wiper switch assembly.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
2 (E) - 13 (C1R) - 10 (+1R)
Rear wiper switch OFF
10 kΩ or higher
2 (E) - 13 (C1R)
Rear wiper switch LO
Below 1 Ω
2 (E) - 10 (+1R)
Rear wiper switch HI
Below 1 Ω
Reinstall the the windshield wiper switch assembly.
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - MAIN BODY ECU, BODY GROUND) |
![]() ![]() |
Disconnect the E8 main body ECU connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E8-9 (WRIN) - E8-10 (WRLO) - Body ground
Rear wiper switch OFF
10 kΩ or higher
E8-9 (WRIN) - Body ground
Rear wiper switch LO
Below 1 Ω
E8-10 (WRLO) - Body ground
Rear wiper switch HI
Below 1 Ω
Reconnect the main body ECU connector.
|
|
||||
| OK | ||
| ||
| 7. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY |
![]() ![]() |
Remove the windshield wiper switch assembly.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
2 (E) - 10 (+1R) - 12 (WR)
Rear washer switch OFF
10 kΩ or higher
2 (E) - 12 (WR)
Rear washer switch ON (Rear wiper switch OFF position side)
Below 1 Ω
2 (E) - 10 (+1R) - 12 (WR)
Rear washer switch ON (Rear wiper switch ON position side)
Below 1 Ω
Reinstall the the windshield wiper switch assembly.
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - MAIN BODY ECU, BODY GROUND) |
![]() ![]() |
Disconnect the E7 main body ECU connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E7-1 (RWSW) - Body ground
Rear washer switch OFF
10 kΩ or higher
E7-1 (RWSW) - Body ground
Rear washer switch ON (Rear wiper switch in ON position)
Below 1 Ω
E7-1 (RWSW) - Body ground
Rear washer switch ON (Rear wiper switch in OFF position)
Below 1 Ω
Reconnect the main body ECU connector.
|
|
||||
| OK | ||
| ||





