2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1628/82 Side Airbag Sensor Assembly LH Initialization Incomplete

Diagnostic trouble codes · Vehicles built from Aug 2012

DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat airbag assembly LH and curtain shield airbag assembly LH) is composed of the center airbag sensor assembly, side airbag sensor assembly LH and rear airbag sensor LH.
The side airbag sensor assembly LH and rear airbag sensor LH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.
DTC B1628/82 is stored when a malfunction is detected in the side collision sensor LH circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1628/82
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor LH circuit.
  2. Side airbag sensor assembly LH malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Side airbag sensor assembly LH
  3. Center airbag sensor assembly

WIRING DIAGRAM

C267557E02

INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).


1. CHECK HISTORY DTC
  1. Check for history DTCs (Click here).

    Result:
    Result
    Proceed to
    History DTC B1627/82 is not output.
    A
    History DTC B1627/82 is output.
    B

    HINT:
    Codes other than history DTC B1627/82 may be output at this time, but they are not related to this check.



B
GO TO DTC B1627/82 (Click here)
A


2. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and side airbag sensor assembly LH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and side airbag sensor assembly LH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


3. CHECK NO. 2 FLOOR WIRE (OPEN)

  1. C268574E03
    Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L4-4 (BBL+) - L4-3 (BBL-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Center Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


4. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

  1. C268575E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L4-4 (BBL+) - Body ground
    Always
    1 MΩ or higher
    L4-3 (BBL-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Center Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


5. CHECK NO. 2 FLOOR WIRE (SHORT)

  1. C268575E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L4-4 (BBL+) - L4-3 (BBL-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Center Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


6. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

  1. C268575E03
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L4-4 (BBL+) - Body ground
    Ignition switch ON
    Below 1 V
    L4-3 (BBL-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Center Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


7. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

  1. C267560E01
    Connect the connector to the center airbag sensor assembly.

  1. Interchange the side airbag sensor assembly LH with RH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs B1623/81 and B1628/82 are not output.
    A
    DTC B1628/82 is output.
    B
    DTC B1623/81 is output.
    C

    HINT:
    Codes other than DTCs B1623/81 and B1628/82 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Center Airbag Sensor Assembly



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← B1625/22 Front Passenger Side - Side Airbag Sensor Malfunction (+ B1627/82) (Nov 2010 – Jul 2012)B1628/82 Front Passenger Side - Side Airbag Sensor Assembly Initialization Incomplete (Jul 2007 – Oct 2010) →