B1623/81 Side Airbag Sensor Assembly RH Initialization Incomplete
Diagnostic trouble codes · Vehicles built from Aug 2012
DESCRIPTION
The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH and curtain shield airbag assembly RH) is composed of the center airbag sensor assembly, side airbag sensor assembly RH and rear airbag sensor RH.The side airbag sensor assembly RH and rear airbag sensor RH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.
DTC B1623/81 is stored when a malfunction is detected for the side collision sensor RH circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1623/81 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
| 1. CHECK HISTORY DTC |
Check for history DTCs (Click here).
- Result:
Result
Proceed to
History DTC B1622/81 is not output.
A
History DTC B1622/81 is output.
B
- HINT:
- Codes other than history DTC B1622/81 may be output at this time, but they are not related to this check.
|
|
||||
| A | |
| 2. CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the center airbag sensor assembly and side airbag sensor assembly RH.
- OK:
- The connectors are properly connected.
- HINT:
- If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the center airbag sensor assembly and side airbag sensor assembly RH.
Check that the terminals of the connectors are not damaged.
- OK:
- The terminals are not deformed or damaged.
|
|
||||
| OK | |
| 3. CHECK FLOOR WIRE (OPEN) |
Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
K2-4 (BBR+) - K2-3 (BBR-)
Always
Below 1 Ω
Disconnect the service wire from connector B.
Text in Illustration *1
Side Airbag Sensor Assembly RH
*2
Center Airbag Sensor Assembly
*3
Floor Wire
*4
Service Wire
*a
Front view of wire harness connector
(to Center Airbag Sensor Assembly)
*b
Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
|
|
||||
| OK | |
| 4. CHECK FLOOR WIRE (SHORT TO GROUND) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
K2-4 (BBR+) - Body ground
Always
1 MΩ or higher
K2-3 (BBR-) - Body ground
Always
1 MΩ or higher
Text in Illustration *1
Side Airbag Sensor Assembly RH
*2
Center Airbag Sensor Assembly
*3
Floor Wire
*a
Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
|
|
||||
| OK | |
| 5. CHECK FLOOR WIRE (SHORT) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
K2-4 (BBR+) - K2-3 (BBR-)
Always
1 MΩ or higher
Text in Illustration *1
Side Airbag Sensor Assembly RH
*2
Center Airbag Sensor Assembly
*3
Floor Wire
*a
Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
|
|
||||
| OK | |
| 6. CHECK FLOOR WIRE (SHORT TO B+) |
Connect the cable to the negative (-) battery terminal.

Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
K2-4 (BBR+) - Body ground
Ignition switch ON
Below 1 V
K2-3 (BBR-) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Text in Illustration *1
Side Airbag Sensor Assembly RH
*2
Center Airbag Sensor Assembly
*3
Floor Wire
*a
Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
|
|
||||
| OK | |
| 7. CHECK SIDE AIRBAG SENSOR ASSEMBLY RH |
Connect the connector to the center airbag sensor assembly.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- Result:
Result
Proceed to
DTCs B1623/81 and B1628/82 are not output.
A
DTC B1623/81 is output.
B
DTC B1628/82 is output.
C
- HINT:
- Codes other than DTCs B1623/81 and B1628/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
Text in Illustration *1
Side Airbag Sensor Assembly LH
*2
Center Airbag Sensor Assembly
|
|
||||
|
|
||||
| A | ||
| ||
