2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

All Doors cannot be Locked / Unlocked Simultaneously

Circuit diagnosis · Vehicles built from Aug 2011

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2011 from Aug 2011

DESCRIPTION

The main body ECU receives switch signals from the door control switch on the power window regulator master switch assembly, door control switch assembly, front door LH key cylinder and front door RH key cylinder, and activates the door lock motor on each door accordingly.

WIRING DIAGRAM

B293847E01

INSPECTION PROCEDURE


1. CHECK OPERATION (ALL DOORS LOCK/ UNLOCK)
  1. All doors can be locked/unlocked at once using the following:

    1. Door control switch on the power window regulator master switch assembly (switch operation)
    2. Door control switch assembly (switch operation)
    3. Door key cylinder linked with door lock on the front door LH (key operation)
    4. Door key cylinder linked with door lock on the front door RH (key operation)

  1. Proceed to the next step according to the symptom if all the doors cannot be locked / unlocked at once.

    Result 
    Result
    Proceed to
    All doors cannot be locked/unlocked at once using door control switch on power window regulator master switch assembly
    A
    All doors cannot be locked/unlocked at once using door control switch assembly
    B
    All doors cannot be locked/unlocked at once using door key cylinder on front door LH
    C
    All doors cannot be locked/unlocked at once using door key cylinder on front door RH
    D



B
Go to step 5

C
Go to step 8

D
Go to step 11
A


2. READ VALUE USING INTELLIGENT TESTER (DOOR CONTROL SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Lock SW-Lock
    Door manual lock switch signal / ON or OFF
    ON: Door control switch on power window regulator master switch assembly is pushed to lock position
    OFF: Door control switch on power window regulator master switch assembly is not pushed
    -
    Door Lock SW-Unlock
    Door manual unlock switch signal / ON or OFF
    ON: Door control switch on power window regulator master switch assembly is pushed to unlock position
    OFF: Door control switch on power window regulator master switch assembly is not pushed
    -

OK:
When the switch is operated, the intelligent tester displays ON and OFF as shown in the table.



NG
Go to step 3
OK

REPLACE MAIN BODY ECU

3. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (DOOR CONTROL SWITCH)
  1. Inspect the power window regulator master switch assembly (door control switch) (Click here).



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
  1. Disconnect the 1K main body ECU connector.

  1. for LHD

    1. Disconnect the H8 power window regulator master switch assembly connector.

  1. for RHD

    1. Disconnect the G8 power window regulator master switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance:
for LHD 
Tester Connection
Condition
Specified Condition
1K-5 (L1) - H8-1 (L1)
Always
Below 1 Ω
1K-1 (UL1) - H8-9 (UL1)
Always
Below 1 Ω
H8-7 (E) - Body ground
Always
Below 1 Ω
1K-5 (L1) - Body ground
Always
10 kΩ or higher
1K-1 (UL1) - Body ground
Always
10 kΩ or higher
for RHD 
Tester Connection
Condition
Specified Condition
1K-5 (L1) - G8-1 (L1)
Always
Below 1 Ω
1K-1 (UL1) - G8-9 (UL1)
Always
Below 1 Ω
G8-7 (E) - Body ground
Always
Below 1 Ω
1K-5 (L1) - Body ground
Always
10 kΩ or higher
1K-1 (UL1) - Body ground
Always
10 kΩ or higher

  1. Reconnect the power window regulator master switch assembly connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

5. READ VALUE USING INTELLIGENT TESTER (DOOR CONTROL SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Lock SW-Lock
    Door manual lock switch signal / ON or OFF
    ON: Passenger side door control switch is pushed to lock position
    OFF: Passenger side door control switch is not pushed
    -
    Door Lock SW-Unlock
    Door manual unlock switch signal / ON or OFF
    ON: Passenger side door control switch is pushed to unlock position
    OFF: Passenger side door control switch is not pushed
    -

OK:
When the switch is operated, the intelligent tester displays ON and OFF as shown in the table.



NG
Go to step 6
OK

REPLACE MAIN BODY ECU

6. INSPECT DOOR CONTROL SWITCH ASSEMBLY
  1. Inspect the door control switch assembly (Click here).



NG
REPLACE DOOR CONTROL SWITCH ASSEMBLY (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL SWITCH ASSEMBLY)
  1. Disconnect the 1K main body ECU connector.

  1. Disconnect the G9 door control switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
1K-5 (L1) - G9-4
Always
Below 1 Ω
1K-1 (UL1) - G9-2
Always
Below 1 Ω
G9-3 - Body ground
Always
Below 1 Ω
1K-5 (L1) - Body ground
Always
10 kΩ or higher
1K-1 (UL1) - Body ground
Always
10 kΩ or higher

  1. Reconnect the door control switch assembly connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

8. READ VALUE USING INTELLIGENT TESTER (FRONT DOOR LH KEY SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Key SW-Lock
    Door key linked lock switch signal / ON or OFF
    ON: Front door LH key cylinder is turned to lock position
    OFF: Front door LH key cylinder is not turned
    -
    P Door Key SW-UL
    Door key linked unlock switch signal / ON or OFF
    ON: Front door LH key cylinder is turned to unlock position
    OFF: Front door LH key cylinder is not turned
    -

OK:
When the door key cylinder is operating, the intelligent tester should display as shown in the table.



NG
Go to step 9
OK

REPLACE MAIN BODY ECU

9. INSPECT FRONT DOOR LOCK ASSEMBLY LH (KEY-LINKED SWITCH)
  1. Inspect the front door lock assembly LH (Click here).



NG
REPLACE FRONT DOOR LOCK ASSEMBLY LH (Click here)
OK


10. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT DOOR LOCK ASSEMBLY LH)
  1. Disconnect the 1K and E6 main body ECU connectors.

  1. Disconnect the H6 front door lock assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
1K-3 (L2) - H6-9
Always
Below 1 Ω
E6-22 (UL2) - H6-10
Always
Below 1 Ω
H6-7 - Body ground
Always
Below 1 Ω
1K-3 (L2) - Body ground
Always
10 kΩ or higher
E6-22 (UL2) - Body ground
Always
10 kΩ or higher

  1. Reconnect the front door lock assembly LH connector.

  1. Reconnect the main body ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

11. READ VALUE USING INTELLIGENT TESTER (FRONT DOOR RH KEY SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Key SW-Lock
    Door key linked lock switch signal / ON or OFF
    ON: Front door RH key cylinder is turned to lock position
    OFF: Front door RH key cylinder is not turned
    -
    Door Key SW-Unlock
    Door key linked unlock switch signal / ON or OFF
    ON: Front door RH key cylinder is turned to unlock position
    OFF: Front door RH key cylinder is not turned
    -

OK:
When the door key cylinder is operated, the intelligent tester displays ON and OFF as shown in the table.



NG
Go to step 12
OK

REPLACE MAIN BODY ECU

12. INSPECT FRONT DOOR LOCK ASSEMBLY RH (KEY-LINKED SWITCH)
  1. Inspect the front door lock assembly RH (Click here).



NG
REPLACE FRONT DOOR LOCK ASSEMBLY RH (Click here)
OK


13. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT DOOR LOCK ASSEMBLY (FRONT PASSENGER SIDE))
  1. Disconnect the 1K and E6 main body ECU connectors.

  1. Disconnect the G7 front door lock assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
1K-3 (L2) - G7-6
Always
Below 1 Ω
E6-22 (UL2) - G7-5
Always
Below 1 Ω
G7-8 - Body ground
Always
Below 1 Ω
1K-3 (L2) - Body ground
Always
10 kΩ or higher
E6-22 (UL2) - Body ground
Always
10 kΩ or higher

  1. Reconnect the front door lock assembly RH connector.

  1. Reconnect the main body ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← All Doors cannot be Locked / Unlocked Simultaneously (Nov 2010 – Jul 2011)Only Driver Door LOCK / UNLOCK Functions do not Operate (Jul 2007 – Oct 2010) →