2011-2016 FJ Cruiser · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Aug 2009


CLEAN CYLINDER BLOCK SUB-ASSEMBLY

A223700
  1. Using a gasket scraper, remove all the gasket material from the top surface of the cylinder block.

  1. Using a soft brush and solvent, thoroughly clean the cylinder block.

    NOTICE:
    If the cylinder is washed at high temperatures, the cylinder liner sticks out beyond the cylinder block. Always wash the cylinder block at a temperature of 45°C (113°F) or less.


INSPECT CYLINDER BLOCK FOR WARPAGE

A221393
  1. Using a precision straightedge and feeler gauge, measure the warpage of the contact surface of the cylinder head gasket.

    Maximum warpage:
    0.05 mm (0.00197 in.)

    If the warpage is more than the maximum, replace the cylinder block.

  1. Visually check the cylinder for vertical scratches. If deep scratches are present, rebore all 6 cylinders.
    If necessary, replace the cylinder block.


INSPECT CYLINDER BORE

A221394E02
  1. Using a cylinder gauge, measure the cylinder bore diameter at positions A and B in the thrust and axial directions.

    Text in Illustration 
    *a
    Thrust Direction
    *b
    Axial Direction
    *c
    Center
    V100135
    Engine Front

    Standard diameter:
    94.000 to 94.012 mm (3.7008 to 3.7013 in.)

    Maximum diameter:
    94.132 mm (3.7060 in.)

    Measurement Position (A):
    10 mm (0.394 in.)

    If the diameter is more than the maximum, replace the cylinder block.


INSPECT RING GROOVE CLEARANCE
  1. Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.

    Standard Ring Groove Clearance:
    Item
    Specified Condition
    No. 1 compression ring
    0.02 to 0.07 mm (0.000787 to 0.00276 in.)
    No. 2 compression ring
    0.02 to 0.06 mm (0.000787 to 0.00236 in.)
    Oil ring
    0.07 to 0.15 mm (0.00276 to 0.00590 in.)

    If the clearance is not as specified, replace the piston with pin sub-assembly.


INSPECT PISTON RING END GAP
  1. Insert the piston ring into the cylinder bore.

  1. Using a piston, push the piston ring a little beyond the bottom of the ring travel, 110 mm (4.33 in.) from the top of the cylinder block.

  1. Using a feeler gauge, measure the end gap.

    Standard End Gap:
    Item
    Specified Condition
    No. 1 compression ring
    0.22 to 0.36 mm (0.00866 to 0.0142 in.)
    No. 2 compression ring
    0.35 to 0.49 mm (0.0138 to 0.0193 in.)
    Oil ring (side rail)
    0.10 to 0.44 mm (0.00394 to 0.0173 in.)

    Maximum End Gap:
    Item
    Specified Condition
    No. 1 compression ring
    1.0 mm (0.0394 in.)
    No. 2 compression ring
    1.1 mm (0.0433 in.)
    Oil ring (side rail)
    1.0 mm (0.0394 in.)

    If the end gap is more than the maximum, replace the piston ring. If the end gap is more than the maximum even with a new piston ring, rebore all 6 cylinders or replace the cylinder block sub-assembly.


CLEAN PISTON WITH PIN SUB-ASSEMBLY

  1. Clean the piston.

    1. A223661
      Using a gasket scraper, remove the carbon from the piston top.

    2. A223662
      Using a groove cleaning tool or broken ring, clean the piston ring grooves.

    3. Using solvent and a brush, thoroughly clean the piston.

      NOTICE:
      Do not use a wire brush.


INSPECT PISTON OIL CLEARANCE

A221395E01
  1. Using a micrometer, measure the piston diameter at a position that is 9.6 mm (0.378 in.) from the bottom of the piston (refer to the illustration).

    Piston diameter:
    93.971 to 93.991 mm (3.6996 to 3.7000 in.)

  1. Subtract the piston diameter measurement from the cylinder bore diameter measurement.

    Standard oil clearance:
    0.009 to 0.051 mm (0.00035 to 0.00201 in.)

    Maximum oil clearance:
    0.11 mm (0.00433 in.)

    If the oil clearance is more than the maximum, replace all 6 pistons. If necessary, replace the cylinder block.


INSPECT PISTON PIN OIL CLEARANCE

A221396E02
  1. Check each mark on the piston and connecting rod.

    Text in Illustration 
    *a
    Front Mark
    *b
    Position Pin Hole Inside Diameter Mark
    *c
    Connecting Rod Bush Inside Diameter Mark

  1. A221397
    Using a caliper gauge, measure the inside diameter of the piston pin hole.

    Standard Piston Pin Hole Inside Diameter:
    Item
    Specified Condition
    Mark A
    22.001 to 22.004 mm (0.86618 to 0.86630 in.)
    Mark B
    22.005 to 22.007 mm (0.86634 to 0.86642 in.)
    Mark C
    22.008 to 22.010 mm (0.86645 to 0.86653 in.)

  1. A146331E03
    Using a micrometer, measure the piston pin diameter.

    Standard Piston Pin Diameter:
    Item
    Specified Condition
    Mark A
    21.997 to 22.000 mm (0.86602 to 0.86614 in.)
    Mark B
    22.001 to 22.003 mm (0.86618 to 0.86626 in.)
    Mark C
    22.004 to 22.006 mm (0.86630 to 0.86642 in.)

    Measurement Position:
    Measurement Position
    Piston Pin Position
    a
    25 mm (0.984 in.) from side edge
    b
    5 mm (0.197 in.) from side edge

  1. Using a caliper gauge, measure the inside diameter of the connecting rod bush.

    Standard Bush Inside Diameter:
    Item
    Specified Condition
    Mark A
    22.005 to 22.008 mm (0.86634 to 0.86645 in.)
    Mark B
    22.009 to 22.011 mm (0.86649 to 0.86657 in.)
    Mark C
    22.012 to 22.014 mm (0.86661 to 0.86669 in.)

  1. Subtract the piston pin diameter measurement from the piston pin hole diameter measurement.

    Standard oil clearance:
    0.001 to 0.007 mm (0.0000394 to 0.000276 in.)

    Maximum oil clearance:
    0.040 mm (0.00157 in.)

    If the oil clearance is more than the maximum, replace the piston with pin sub-assembly.

  1. Subtract the piston pin diameter measurement from the bush inside diameter measurement.

    Standard oil clearance:
    0.005 to 0.011 mm (0.000197 to 0.000433 in.)

    Maximum oil clearance:
    0.050 mm (0.00197 in.)

    If the oil clearance is more than the maximum, replace the connecting rod sub-assembly. If necessary, replace the piston with pin sub-assembly.


INSPECT CONNECTING ROD SUB-ASSEMBLY

A132171

  1. Using a rod aligner and feeler gauge, check the connecting rod alignment.

    1. Check for bend.

      Maximum bend:
      0.05 mm (0.00197 in.) per 100 mm (3.94 in.)

      If the bend is more than the maximum, replace the connecting rod sub-assembly.

    2. A132172
      Check for twist.

      Maximum twist:
      0.15 mm (0.00591 in.) per 100 mm (3.94 in.)

      If the twist is more than the maximum, replace the connecting rod sub-assembly.


INSPECT CRANKSHAFT
  1. Using a dial indicator, measure the runout at the center journal.

    Maximum circle runout:
    0.06 mm (0.00236 in.)

    If the circle runout is more than the maximum, replace the crankshaft.

  1. A076059E01
    Using a micrometer, measure the diameter of each main journal.

    Standard diameter:
    71.988 to 72.000 mm (2.8342 to 2.8346 in.)

    If the diameter is not as specified, check the oil clearance. If necessary, replace the crankshaft.

  1. Check each main journal for taper and out-of-round as shown in the illustration.

    Maximum taper and out-of-round:
    0.02 mm (0.000787 in.)

    If the taper and out-of-round is more than the maximum, replace the crankshaft.

  1. A076060E01
    Using a micrometer, measure the diameter of each crank pin.

    Standard diameter:
    55.992 to 56.000 mm (2.2044 to 2.2047 in.)

    If the diameter is not as specified, check the oil clearance. If necessary, replace the crankshaft.

  1. Check each crank pin for taper and out-of-round as shown in the illustration.

    Maximum taper and out-of-round:
    0.02 mm (0.000787 in.)

    If the taper and out-of-round is more than the maximum, replace the crankshaft.


INSPECT CONNECTING ROD BOLT

A109692E12
  1. Using a vernier caliper, measure the tension portion diameter of the bolt.

    Text in Illustration 
    *a
    Measuring Point

    Standard diameter:
    7.2 to 7.3 mm (0.283 to 0.287 in.)

    Minimum diameter:
    7.0 mm (0.276 in.)

    If the diameter is less than the minimum, replace the connecting rod bolt.


INSPECT CRANKSHAFT BEARING CAP SET BOLT

A223293E02
  1. Using a vernier caliper, measure the thread outside diameter of the crankshaft bearing cap set bolt.

    Text in Illustration 
    *a
    Measuring Area

    Standard diameter:
    10.0 to 10.2 mm (0.394 to 0.402 in.)

    If the result is not as specified, replace the crankshaft bearing cap set bolt.


INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY

A188915
  1. Push the check valve with a pin to check if it is stuck. If stuck, replace the oil nozzle.

  1. Push the check valve with a pin to check if it moves smoothly.
    If it does not move smoothly, clean or replace the oil nozzle.

  1. A190792E01
    While covering A, apply air into B. Check that air does not leak through C. Perform the check again while covering B and applying air into A.
    If air leaks, clean or replace the oil nozzle.

  1. A190793E01
    Push the check valve while covering A, and blow air into B. Check that air passes through C. Perform the check again while covering B, pushing the check valve and blowing air into A.
    If air does not pass through C, clean or replace the oil nozzle.

← DISASSEMBLY (from Aug 2009)REPLACEMENT (from Aug 2009) →