2011-2016 FJ Cruiser · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Nov 2010 – Jul 2013

Versions by build date: Aug 2009 – Oct 2010 Nov 2010 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
(Click here)

2. SET NO. 1 CYLINDER TO TDC / COMPRESSION
  1. Temporarily tighten the pulley set bolt.

  1. A222172E01
    Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH block bore center line (TDC/compression).
    Text in Illustration 
    *1
    Center Line
    *2
    Timing Mark
    *3
    Sensor Plate

  1. A225378E01
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If not, turn the crankshaft clockwise 1 revolution (360°) and align the timing marks as above.
    Text in Illustration 
    *1
    Timing Mark


3. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

A124589E05
  1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.

    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate
    *3
    Pin

  1. Move the stopper plate downward to set the lock, and insert a pin of φ1.27 mm (0.0500 in.) into the stopper plate hole.

  1. A095165E02
    Remove the 2 bolts and No. 1 chain tensioner assembly.


4. REMOVE CHAIN TENSIONER SLIPPER

A223730
  1. Remove the chain tensioner slipper.


5. REMOVE CHAIN SUB-ASSEMBLY

A221173E01
  1. Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing sprocket.

    Text in Illustration 
    *1
    Center Line
    *2
    Timing Mark
    *3
    Sensor Plate

  1. Remove the pulley set bolt.

  1. A221174
    Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.

  1. A095682E13
    Turn the camshaft timing gear assembly on bank 1 clockwise approximately 60° so that it is as shown in the illustration. Be sure to loosen the chain subassembly between the banks.

  1. Remove the chain sub-assembly.

    Text in Illustration 
    *a
    Bank 1:


6. REMOVE NO. 1 IDLE GEAR SHAFT

A221175
  1. Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.


7. REMOVE NO. 1 CHAIN VIBRATION DAMPER

A223642
  1. Remove the 2 bolts and No. 1 chain vibration damper.


8. REMOVE NO. 2 CHAIN VIBRATION DAMPER

A221176
  1. Remove the 2 No. 2 chain vibration dampers.


9. REMOVE CRANKSHAFT TIMING SPROCKET

A158530E01
  1. Remove the crankshaft timing sprocket.


10. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

A221132E01
  1. While raising the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 2 chain tensioner assembly.

    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push

  1. A221177E01
    Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold
    SST
    09922-10010  

    NOTICE:
    Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.

  1. Remove the 2 bolts and the camshaft timing gear assembly together with the No. 2 chain.


11. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

A221178
  1. Remove the bolt and No. 2 chain tensioner assembly.


12. REMOVE CAMSHAFT BEARING CAP (for Bank 1)

A129700E06
  1. Check that the camshafts are positioned as shown in the illustration.

    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View

  1. A221179E01
    Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.

  1. A221180E01
    Uniformly loosen and remove the 12 bearing cap bolts in several steps in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 camshaft bearing caps.

  1. Remove the camshaft and No. 2 camshaft.


13. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

A221181E01
  1. Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.

    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly RH.

    HINT:
    Tape the screwdriver tip before use.


14. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

A221182E01
  1. While pushing down the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 3 chain tensioner assembly.

    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push

  1. A223637E01
    Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold
    SST
    09922-10010  

    NOTICE:
    Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.

  1. Remove the 2 bolts and the camshaft timing gear together with the No. 2 chain.


15. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

A221183
  1. Remove the bolt and No. 3 chain tensioner assembly.


16. REMOVE CAMSHAFT BEARING CAP (for Bank 2)

A223636E01
  1. Check that the camshafts are positioned as shown in the illustration.

    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View

  1. A221184E01
    Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.

  1. A221185E01
    Uniformly loosen and remove the 13 bearing cap bolts in several steps and in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 camshaft bearing caps.

  1. Remove the No. 3 camshaft and No. 4 camshaft.


17. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

A221186E01
  1. Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.

    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly LH.

    HINT:
    Tape the screwdriver tip before use.


18. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Remove the 24 valve rocker arms from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


19. REMOVE VALVE LASH ADJUSTER ASSEMBLY
  1. Remove the 24 valve lash adjusters from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


20. REMOVE VALVE STEM CAP
  1. Remove the 24 valve stem caps from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


21. REMOVE CYLINDER HEAD SUB-ASSEMBLY

A221092E01
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head sub-assembly.
    2. Cylinder head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Arrange the removed parts in the correct order.

  1. Remove the cylinder head sub-assembly.


22. REMOVE CYLINDER HEAD LH

A221093E01
  1. Uniformly loosen and remove the 2 cylinder head set bolts in several steps and in the sequence shown in the illustration.

  1. A221094E01
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head sub-assembly.
    2. Cylinder head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Be sure to keep the removed parts for each installation position separate.

  1. Remove the cylinder head LH.


23. REMOVE CYLINDER HEAD GASKET

24. REMOVE NO. 2 CYLINDER HEAD GASKET
← REMOVAL (Aug 2009 – Oct 2010)REMOVAL (Aug 2013 – Jul 2014) →