2011-2016 FJ Cruiser · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built Aug 2009 – Oct 2010

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL STUD BOLT

A225385E01
  1. Install the oil pan stud bolt.

    1. Using an E6 and E8 "TORX" socket wrench, install the 6 stud bolts as shown in the illustration.

      Torque:
      for stud bolt A:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }
      for stud bolt B and C:
      4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. A225387E01
    Install the cylinder head cover LH stud bolt.

    1. Using a E6 "TORX" socket wrench, install the stud bolt as shown in the illustration.

      Torque:
      4.0 N*m{ 41 kgf*cm , 35 in.*lbf }


2. INSTALL RING PIN

  1. Using a plastic-faced hammer, tap in new ring pins to the camshaft housing.

    A225382E02

    Text in Illustration 
    *a
    LH:
    *b
    RH:
    *c
    Protrusion Height
    -
    -

    Standard protrusion height:
    2.7 to 3.3 mm (0.106 to 0.130 in.)


3. INSTALL STRAIGHT PIN

  1. Using a plastic-faced hammer, tap in new straight pins to the camshaft housing.

    A225383E02

    Text in Illustration 
    *a
    LH:
    *b
    RH:
    *c
    Protrusion Height
    -
    -

    Standard Protrusion:
    Item
    Specified Condition
    Ring pin A
    7.7 to 8.3 mm (0.303 to 0.327 in.)
    Ring pin B
    5.7 to 6.3 mm (0.224 to 0.248 in.)


4. INSTALL REAR CRANKSHAFT OIL SEAL

A076268E01
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the rear oil seal retainer edge.

    SST
    09223-78010  

  1. Apply MP grease to the lip of the oil seal.


5. INSTALL ENGINE REAR OIL SEAL RETAINER
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the oil seal retainer or cylinder block.

  1. A076269E06
    Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    *1
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2 to 3 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the oil seal retainer within 3 minutes after applying seal packing.

  1. Install the oil seal retainer with the 5 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    1. When installing the oil seal retainer, make sure the lip of the oil seal is not damaged.
    2. When installing the oil seal retainer, make sure the lip of the oil seal is not folded incorrectly.
    3. Do not start the engine for at least 2 hours after installation.


6. INSTALL CYLINDER BLOCK WATER JACKET SPACER

A225710E02
  1. Install the 2 water jacket spacers as shown in the illustration.

    Text in Illustration 
    *a
    UP Mark
    *b
    L Mark
    *c
    R Mark

    NOTICE:
    Make sure that face the "L mark", "R mark" and "UP mark" are oriented as shown in the illustration.


7. INSTALL KNOCK SENSOR

  1. A078438E15
    Install the 2 sensors with the 2 bolts as shown in the illustration.
    Text in Illustration 
    *a
    for Bank 2:
    *b
    for Bank 1:
    *c
    Engine Rear
    *d
    Top
    *e
    Engine Front

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 sensor connectors.


8. INSTALL NO. 1 WATER OUTLET PIPE
  1. Install the No. 1 water outlet pipe with the 2 nuts and bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 4 wire harness clamps.


9. INSTALL CYLINDER HEAD GASKET
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head or cylinder block.

  1. A222175E02
    Apply seal packing to a new cylinder head gasket as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing
    *b
    Gasket

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2.5 to 3.0 mm (0.0984 to 0.118 in.)

    Seal packing application range 
    A
    10 to 15 mm (0.394 to 0.591 in.)
    B
    1.25 to 1.5 mm (0.0492 to 0.0591 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head gasket within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not add engine oil within 2 hours of installation.

  1. A221095E02
    Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.

    NOTICE:
    Make sure that the gasket is installed facing the proper direction.

    Text in Illustration 
    *a
    Lot No.
    V100135
    Engine Front


10. INSTALL CYLINDER HEAD SUB-ASSEMBLY
  1. Place the cylinder head on the cylinder block.

    NOTICE:
    1. Gently place the cylinder head in order not to damage the gasket with the bottom part of the head.
    2. Make sure that no oil is on the mounting surface of the cylinder head.

    HINT:
    The cylinder head bolts are tightened in 3 progressive steps.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.

  1. Step 1:

    1. A221092E02
      Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps and in the sequence shown in the illustration.

      Torque:
      36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Step 2:

    1. Mark the front side of each cylinder head bolt head with paint.

    2. Tighten the cylinder head bolts another 90°.

  1. Step 3:

    1. Tighten the cylinder head bolts an additional 90°.

    2. Check that the paint mark is now at a 180° angle to the front.

      NOTICE:
      Thoroughly wipe clean any seal packing.


11. INSTALL NO. 2 CYLINDER HEAD GASKET
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head or cylinder block.

  1. A222176E02
    Apply seal packing to a new cylinder head gasket as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing
    *b
    Gasket

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2.5 to 3.0 mm (0.0984 to 0.118 in.)

    Seal packing application range 
    A
    10 to 15 mm (0.394 to 0.591 in.)
    B
    1.25 to 1.5 mm (0.0492 to 0.0591 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head gasket within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not add engine oil within 2 hours of installation.

  1. A221096E02
    Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.

    NOTICE:
    Make sure that the gasket is installed facing the proper direction.

    Text in Illustration 
    *a
    Lot No.
    V100135
    Engine Front


12. INSTALL CYLINDER HEAD LH
  1. Place the cylinder head on the cylinder block.

    NOTICE:
    1. Gently place the cylinder head in order not to damage the gasket with the bottom part of the head.
    2. Make sure that no oil is on the mounting surface of the cylinder head.

    HINT:
    The cylinder head bolts are tightened in 3 progressive steps.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.

  1. Step 1:

    1. A221094E02
      Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps in the sequence shown in the illustration.

      Torque:
      36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Step 2:

    1. Mark the front side of each cylinder head bolt head with paint.

    2. Tighten the cylinder head bolts another 90°.

  1. Step 3:

    1. Tighten the cylinder head bolts an additional 90°.

    2. Check that the paint mark is now at a 180° angle to the front.

  1. A221093E02
    Tighten the 2 bolts in the order shown in the illustration.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Thoroughly wipe clean any seal packing.


13. INSTALL VALVE STEM CAP
  1. Apply a light coat of engine oil to the valve stem caps.

  1. Install the 24 valve stem caps to the cylinder head.


14. INSTALL VALVE LASH ADJUSTER ASSEMBLY
  1. Inspect the valve lash adjuster (Click here).

  1. Install the 24 valve lash adjusters to the cylinder head.

    NOTICE:
    Install the lash adjuster at the same place it was removed from.


15. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Apply engine oil to the lash adjuster tips and valve stem cap ends.

  1. A221097E01
    Install the 24 valve rocker arms as shown in the illustration.
    Text in Illustration 
    *1
    Valve Rocker Arm
    *2
    Lash Adjuster
    *3
    Valve Stem
    *4
    Valve Stem Cap


16. INSTALL CAMSHAFT BEARING CAP (for Bank 2)
  1. Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.

  1. Install the No. 3 camshaft and No. 4 camshaft to the camshaft housing.

  1. A224655
    Check the marks and numbers on the camshaft bearing caps and place each of them in the proper position facing the proper direction.

  1. A221188E01
    Temporarily tighten the 8 bolts in the order shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


17. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH

A221097E01
  1. Make sure that the valve rocker arm is installed as shown in the illustration.

    Text in Illustration 
    *1
    Valve Rocker Arm
    *2
    Lash Adjuster
    *3
    Valve Stem
    *4
    Valve Stem Cap

  1. A221189E01
    Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    *1
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    3.5 to 4.5 mm (0.138 to 0.177 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the camshaft housing within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

  1. A223640E01
    Install the camshaft housing sub-assembly LH and tighten the 13 bolts in the order shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    NOTICE:
    1. When installing the camshaft housing sub-assembly LH, it is necessary to correctly position the camshafts as shown in the illustration. Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated with a piston at TDC, valve contact will occur.
    2. If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly LH, clean the installation surfaces, and reapply seal packing.
    3. If the camshaft housing sub-assembly LH is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.
    4. Do not start the engine for at least 2 hours after installing.

  1. A221184E02
    Tighten the 8 bolts in the order shown in the illustration.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    NOTICE:
    Thoroughly wipe clean any seal packing.


18. INSTALL CAMSHAFT BEARING CAP (for Bank 1)
  1. Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.

  1. Install the camshaft and No. 2 camshaft to the camshaft housing.

  1. A221190
    Check the marks and numbers on the camshaft bearing caps and place each of them in the proper position facing the proper direction.

  1. A221387E01
    Temporarily tighten the 8 bearing cap bolts in the order shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


19. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH

A221097E01
  1. Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.

    Text in Illustration 
    *1
    Valve Rocker Arm
    *2
    Lash Adjuster
    *3
    Valve Stem
    *4
    Valve Stem Cap

  1. A221388E01
    Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    *1
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    3.5 to 4.5 mm (0.138 to 0.177 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the camshaft housing within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

  1. A223641E01
    Install the camshaft housing sub-assembly RH and tighten the 12 bolts in the order shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    NOTICE:
    1. When installing the camshaft housing RH, it is necessary to correctly position the camshafts as shown in the illustration.
      Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated with a piston at TDC, valve contact will occur.
    2. If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly RH, clean the installation surfaces, and reapply seal packing.
    3. If the camshaft housing sub-assembly RH is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.
    4. Do not start the engine for at least 2 hours after installing.

  1. A221179E02
    Tighten the 8 bolts in the order shown in the illustration.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    NOTICE:
    Thoroughly wipe clean any seal packing.


20. INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY (for Bank 2)

A222171E01
  1. Install the No. 3 chain tensioner assembly with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Push in the tensioner and insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the tensioner.

    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push


21. INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

A227957E01
  1. Align the mark plates (yellow) with the timing marks of the camshaft timing gear assemblies as shown in the illustration.

    Text in Illustration 
    *1
    Timing Mark
    *2
    Mark Plate

  1. Apply a light coat of engine oil to the bolt threads and bolt-seating surface.

  1. Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear LH with the No. 2 chain sub-assembly installed.

  1. A223637E01
    Using SST to hold the hexagonal portion of each camshaft, tighten the bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold
    SST
    09922-10010  

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Remove the pin from the No. 3 chain tensioner assembly.


22. INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY (for Bank 1)

A222174E01
  1. Install the No. 2 chain tensioner assembly with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Push in the No. 2 chain tensioner assembly and insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the tensioner.

    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push


23. INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

A227958E01
  1. Align the mark plates (yellow) with the timing marks of the camshaft timing gear assemblies as shown in the illustration.

    Text in Illustration 
    *1
    Timing Mark
    *2
    Mark Plate

  1. Apply a light coat of engine oil to the bolt threads and bolt-seating surface.

  1. Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear assembly with the No. 2 chain sub-assembly installed.

  1. A221177E01
    Using SST to hold the hexagonal portion of each camshaft, tighten the bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold
    SST
    09922-10010  

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Remove the pin from the No. 2 chain tensioner assembly.


24. INSTALL NO. 1 CHAIN VIBRATION DAMPER

A223642
  1. Install the No. 1 chain vibration damper with the 2 bolts.

    Torque:
    23 N*m{ 229 kgf*cm , 17 ft.*lbf }


25. INSTALL NO. 2 CHAIN VIBRATION DAMPER

A221176
  1. Install the 2 No. 2 chain vibration dampers.


26. INSTALL CRANKSHAFT TIMING SPROCKET

A076293E02
  1. Align the key groove of the timing sprocket with the timing sprocket set key.

  1. Install the timing sprocket to the crankshaft with the sprocket facing inward as shown in the illustration.

    Text in Illustration 
    *a
    Inward


27. INSTALL NO. 1 IDLE GEAR SHAFT
  1. Apply a light coat of engine oil to the rotating surface of the No. 1 idle gear shaft.

  1. A223643E01
    Temporarily install the No. 1 idle gear shaft and No. 1 idle gear with the No. 2 idle gear shaft while aligning the knock pin of the No. 1 idle gear shaft with the knock pin groove of the cylinder block.
    Text in Illustration 
    *1
    Knock Pin

    NOTICE:
    Make sure that the idle gear is installed facing the proper direction.

  1. Using a 10 mm hexagon wrench, tighten the No. 2 idle gear shaft.

    Torque:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

  1. Remove the bar from the chain tensioner.


28. INSTALL CHAIN SUB-ASSEMBLY

A223644E01
  1. Align the mark plate and timing marks as shown in the illustration and install the chain.

    Text in Illustration 
    *1
    Mark Plate
    *2
    Timing Mark

    HINT:
    The camshaft mark plates are orange.

  1. A221174
    Do not pass the chain over the crankshaft, just temporarily place it on the crankshaft.

  1. A223645E01
    Turn the camshaft timing gear assembly on bank 1 counterclockwise to tighten the chain between the banks.
    Text in Illustration 
    *1
    Chain Plate
    *a
    When the idle sprocket is reused:
    *b
    Mark
    *c
    Align
    V100135
    Turn

    NOTICE:
    When the idle sprocket assembly is reused, align the chain plate with the mark where the plate had been in order to tighten the chain between the banks.

  1. A223646E01
    Align the mark plate and timing marks as shown in the illustration and install the chain to the crankshaft timing sprocket.
    Text in Illustration 
    *1
    Mark Plate
    *2
    Timing Mark

    HINT:
    The crankshaft mark plate is yellow.

  1. Temporarily tighten the pulley set bolt.

  1. A223647E01
    Turn the crankshaft clockwise to set it to the RH block bore center line (TDC/compression).
    Text in Illustration 
    *1
    Center Line
    *2
    Timing Mark
    *3
    Sensor Plate


29. INSTALL CHAIN TENSIONER SLIPPER

A223730
  1. Install the chain tensioner slipper.


30. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

A178214E01
  1. Turn the stopper plate of the tensioner clockwise and push in the plunger of the tensioner as shown in the illustration.

    Text in Illustration 
    *1
    Stopper Plate
    *a
    Push

  1. Turn the stopper plate of the tensioner counterclockwise and insert a pin of φ1.27 mm (0.0500 in.) into the holes on the stopper plate and tensioner to fix the stopper plate in place.

  1. A095165E02
    Install the chain tensioner with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Remove the pin from the No. 1 chain tensioner.


31. INSPECT VALVE TIMING
  1. Check the camshaft timing marks.

    NOTICE:
    1. Check each timing mark from a viewpoint directly inline with the center of the camshaft and the timing mark on each camshaft timing gear.
    2. If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.

  1. Check that each camshaft timing mark is positioned as shown in the illustration.

    A223648E02

    Text in Illustration 
    *1
    Timing Mark
    -
    -
    *a
    Viewpoint
    -
    -

    HINT:
    A182780E01
    for the intake camshaft:
    Be sure to check mark A at the point when marks B, C, and D are positioned in line. If the marks are checked from any other viewpoint, they cannot be checked correctly.

  1. If the valve timing is misaligned, reinstall the timing chain.

  1. Remove the pulley set bolt.


32. INSTALL FRONT CRANKSHAFT OIL SEAL

A225390E01
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.

    SST
    09223-22010  
    09506-35010  

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap on the oil seal at an angle.
    3. Make sure that the oil seal edge does not stick out of the timing chain case.


33. INSTALL WATER PUMP ASSEMBLY

A221171
  1. Install a new gasket and the water pump with the 8 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }


34. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.

    A225681E02

    Text in Illustration 
    *a
    Cylinder head and cylinder block side:
    *b
    Timing chain cover side:
    *c
    Clean and degrease
    -
    -

    NOTICE:
    Be sure to clean and degrease the contact surfaces, especially the surfaces indicated in the illustration.

  1. Apply a light coat of engine oil to a new oil pump gasket.

  1. Install the oil pump gasket.

  1. A225682E01
    Apply seal packing as shown in the illustration.
    Text in Illustration 
    *1
    Seal Diameter
    V100135
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)

  1. Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.

    A221403E01

    Text in Illustration 
    *a
    Be sure to apply seal packing
    *b
    Dashed line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent)
    *c
    Continuous line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent)
    *d
    Alternate long and short dashed line area (Seal packing: Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent)
    *e
    Diagonal line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent)
    -
    -

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
    Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent

    NOTICE:
    1. When there is oil on the contact surfaces, wipe them with an oil-free cloth before applying seal packing.
    2. Install the chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.


    Application Specification:
    Area
    Seal Packing Diameter
    Application Position from Inside Seal Line
    Continuous Line Area
    4.5 mm (0.177 in.) or more
    3.0 to 4.0 mm (0.118 to 0.158 in.)
    Alternate Long and Short Dashed Line Area
    3.5 mm (0.138 in.) or more
    2.0 to 3.0 mm (0.0787 to 0.118 in.)
    Dashed Line Area
    3.5 mm (0.138 in.) or more
    3.0 to 4.0 mm (0.118 to 0.158 in.)
    Diagonal Line Area
    6.0 mm (0.236 in.) or more
    5.0 mm (0.197 in.)

  1. A221405E01
    Align the oil pump drive rotor spline and the crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.
    Text in Illustration 
    *1
    Drive Rotor Spline
    *2
    Crankshaft

  1. Install the timing chain cover with the 26 bolts labeled A, B, C, D and the 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    A221406E01

    Text in Illustration 
    *1
    Nut
    -
    -
    *a
    Area 1
    *b
    Area 2
    *c
    Area 3
    *d
    Area 4

    Bolt Length:
    Item
    Length
    Bolt A
    25 mm (0.984 in.)
    Bolt B
    55 mm (2.17 in.)
    Bolt C
    35 mm (1.38 in.)
    Bolt D
    65 mm (2.56 in.)

    NOTICE:
    Make sure that there is no oil on the bolt threads.

  1. Fully tighten the bolts in Area 1.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }

    HINT:
    Tighten the bolts from bottom to top as shown in the illustration.

  1. Fully tighten the bolts in Area 2.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

  1. Fully tighten the bolts in Area 3.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    HINT:
    Tighten the bolts and nuts from top to bottom as shown in the illustration.

  1. Fully tighten the bolts in Area 4.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    HINT:
    Tighten the bolts from bottom to top as shown in the illustration.

    NOTICE:
    1. Do not start the engine for at least 2 hours after installing it.
    2. Wipe off any seal packing that seeped out around the surfaces of the oil pan and head cover and make sure that there is no seal packing seeping out around the edges.


35. INSTALL NO. 1 OIL PAN BAFFLE PLATE

A224779
  1. Install the No. 1 oil pan baffle plate with the 6 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


36. INSTALL OIL PAN SUB-ASSEMBLY
  1. Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder block, rear oil seal retainer and oil pan.

  1. Install 3 new O-rings to the timing chain cover.

  1. A222121E02
    Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan within 3 minutes after applying seal packing.

  1. A223671E01
    Install the oil pan with the 17 bolts (A, B, C, D and E) and 2 nuts. Tighten the bolts and nuts uniformly in several steps.
    Text in Illustration 
    *1
    Nut

    Torque:
    for bolt A, B, C, E and nut:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for bolt D:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Bolt Length:
    Item
    Length
    Bolt A
    60 mm (2.36 in.)
    Bolt B
    45 mm (1.77 in.)
    Bolt C
    25 mm (0.984 in.)
    Bolt D
    16 mm (0.630 in.)
    Bolt E
    70 mm (2.76 in.)

    NOTICE:
    Do not start the engine for at least 2 hours after the installation.


37. INSTALL OIL STRAINER SUB-ASSEMBLY
  1. Install a new gasket and the oil strainer with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


38. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

A174349E03
  1. Apply seal packing in a continuous line as shown in the illustration.

    Text in Illustration 
    *a
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the No. 2 oil pan within 3 minutes after applying seal packing.

  1. A225446
    Install the No. 2 oil pan with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    1. Tighten the nuts first. After tightening the bolts, check that the nuts and bolts are tightened to the specified torque.
    2. Do not start the engine for at least 2 hours after the installation.


39. INSTALL OIL PAN DRAIN PLUG
  1. Install the drain plug and a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


40. POUR ENGINE OIL

A224782

HINT:
Before installing the cylinder head cover, pour engine oil into the locations shown in the illustration.


41. INSTALL SPARK PLUG TUBE GASKET

A100218E05
  1. Using a utility knife, cut off the seal part of the removed gasket.

    Text in Illustration 
    V100155
    Area to cut off

  1. A226558E01
    Using the removed gasket and a hammer, tap in a new gasket until it stops.
    Text in Illustration 
    *1
    Removed Gasket
    *2
    New Gasket

    HINT:
    If the removed gasket does not fit on the new one, correct the removed one with pliers.

  1. Apply a light coat of MP grease to the gasket lip.

  1. Return the ventilation baffle plate claws to the original positions.


42. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover or cylinder head cover.

  1. A223667
    Apply seal packing as shown in the illustration.
    Text in Illustration 
    V100135
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2 to 3 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

  1. A221164
    Install 3 new gaskets as shown in the illustration.

  1. Install a new gasket to the cylinder head cover.

  1. Install a new seal washer to the bolt.

  1. A221162E01
    Temporarily install the cylinder head cover with the 12 bolts. Tighten the bolts uniformly in several steps.
    Text in Illustration 
    V100135
    Bolt A
    V100136
    Bolt B
    V100137
    Bolt C
    V100138
    Bolt D

    Torque:
    for bolt A and D:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B and C:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    Bolt Length:
    Item
    Length
    A
    25 mm (0.984 in.)
    B
    35 mm (1.38 in.)
    C
    65 mm (2.56 in.)
    D
    60 mm (2.36 in.)

    NOTICE:
    Do not start the engine for at least 2 hours after the installation.


43. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover or cylinder head cover.

  1. A223664
    Apply seal packing as shown in the illustration.
    Text in Illustration 
    V100135
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2 to 3 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

  1. A223665
    Install 3 new gaskets as shown in the illustration.

  1. Install a new gasket to the cylinder head cover.

  1. Install a new seal washer to the bolt.

  1. A221163E01
    Temporarily install the cylinder head cover with the 12 bolts. Tighten the bolts uniformly in several steps.
    Text in Illustration 
    V100135
    Bolt A
    V100136
    Bolt B
    V100137
    Bolt C
    V100138
    Bolt D

    Torque:
    for bolt A and D:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B and C:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    Bolt Length:
    Item
    Length
    A
    25 mm (0.984 in.)
    B
    35 mm (1.38 in.)
    C
    70 mm (2.76 in.)
    D
    60 mm (2.36 in.)

    NOTICE:
    Do not start the engine for at least 2 hours after the installation.


44. INSTALL CRANKSHAFT PULLEY

A076309E03
  1. Using SST, install the crankshaft pulley with the pulley set bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  

    Torque:
    260 N*m{ 2651 kgf*cm , 192 ft.*lbf }


45. INSTALL VENTILATION VALVE SUB-ASSEMBLY
  1. Apply adhesive to 2 or 3 threads of the ventilation valve.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. A224732
    Install the ventilation valve.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

  1. Install the ventilation valve hose.


46. INSTALL SPARK PLUG
  1. Install the 6 spark plugs.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


47. INSTALL REAR WATER BY-PASS JOINT

A076535E04
  1. Apply soapy water to a new O-ring and install it to the water outlet pipe. Then install 2 new gaskets to the water ports LH and RH.

    Text in Illustration 
    *1
    New O-Ring
    *2
    New Gasket

  1. A076534E01
    Install the rear water by-pass joint with the 2 bolts and 4 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


48. INSTALL WATER INLET HOUSING
  1. Install the 3 water by-pass hoses.

  1. Apply soapy water to a new O-ring, install it to the water outlet pipe.

  1. Install a new gasket to the water pump.

  1. Install the water inlet with the 5 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 3 water by-pass hoses.


49. INSTALL OIL FILTER BRACKET
  1. Install the oil filter bracket and new gasket with the 2 nuts and bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


50. INSTALL OIL FILTER ELEMENT
  1. Clean the inside of the oil filter cap, the threads and O-ring groove.

  1. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

  1. Set a new oil filter element to the oil filter cap.

  1. Remove any dirt or foreign matter from the installation surface of the engine.

  1. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

  1. A222104E01
    Using SST, tighten the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Bracket Clip
    *a
    No Clearance
    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    1. When tightening the oil filter cap, do not remove the oil filter bracket clip.
    2. Make sure that the oil filter is installed securely as shown in the illustration.
    3. Be careful that the O-ring does not get caught between the parts.

  1. A222105E01
    Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

  1. Install the oil filter drain plug.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Be careful that the O-ring does not get caught between the parts.


51. INSTALL NO. 2 OIL PIPE
  1. Make sure that there is no foreign matter on the mesh of the oil control valve filter RH.

    NOTICE:
    Do not touch the mesh when installing the oil control valve filter.

  1. Install a new gasket and temporarily install the oil pipe (on the cylinder head side) with the oil check valve bolt.

  1. Install the oil control valve filter RH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the head cover side).

  1. Tighten the oil pipe union (on the cylinder head side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.

  1. Tighten the oil pipe union (on the head cover side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }


52. INSTALL NO. 1 OIL PIPE
  1. Make sure that there is no foreign matter on the mesh of the oil control valve filter LH.

    NOTICE:
    Do not touch the mesh when installing the oil control valve filter.

  1. Install a new gasket and temporarily install the oil pipe (on the cylinder head side) with the oil check valve bolt.

  1. Install the oil control valve filter LH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the head cover side).

  1. Tighten the oil pipe union (on the cylinder head side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.

  1. Tighten the oil pipe union (on the head cover side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }


53. INSTALL OIL FILLER CAP HOUSING

A221161E01
  1. Install a new gasket and the oil filler cap housing with the 2 nuts.

    Text in Illustration 
    *1
    New Gasket

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the oil filler cap.


54. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

A224730
  1. RH:

    1. Apply a light coat of engine oil to 2 new O-rings.

    2. Install the 2 O-rings to the 2 oil control valves.

    3. Install the 2 oil control valves with the 2 bolts.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

      NOTICE:
      Be careful that the O-ring is not cracked when installing the camshaft timing oil control valve.

  1. A224731
    LH:

    1. Apply a light coat of engine oil to 2 new O-rings.

    2. Install the 2 O-rings to the 2 oil control valves.

    3. Install the 2 oil control valves with the 2 bolts.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

      NOTICE:
      Be careful that the O-ring is not cracked when installing the camshaft timing oil control valve.


55. INSTALL CRANKSHAFT POSITION SENSOR

A224727
  1. Install the sensor with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


56. INSTALL VVT SENSOR

A224728
  1. RH:
    Install the 2 VVT sensors with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. A224729
    LH:
    Install the 2 VVT sensors with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


57. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
  1. Apply adhesive to 2 or 3 threads of the drain cock end.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. A223705E02
    Install the drain cock.
    Text in Illustration 
    *a
    LH:
    *b
    RH:
    *c
    Front

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    NOTICE:
    1. Install the drain cock within 3 minutes after applying adhesive.
    2. Do not expose the drain cock to coolant within 1 hour of the installation.

  1. Rotate the drain cock clockwise as shown in the illustration.

    NOTICE:
    1. Do not rotate the drain cock by more than 1 revolution (360°) after tightening the drain cock to the specified torque.
    2. Do not loosen the drain cock after setting it correctly.

  1. Install the water drain cock plugs to the water drain cocks.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }


58. INSTALL ENGINE COOLANT TEMPERATURE SENSOR
  1. Install a new gasket to the sensor.

  1. A224726
    Using a 19 mm deep socket wrench, install the sensor.

    Torque:
    20 N*m{ 200 kgf*cm , 14 ft.*lbf }


59. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY
  1. Apply adhesive to 2 or 3 threads of the oil pressure switch.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Do not apply adhesive to the oil inlet port of the oil pressure switch.

  1. A224725
    Using a 24 mm deep socket wrench, install the oil pressure switch.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

← REASSEMBLY (Jul 2007 – Jul 2009)REASSEMBLY (Nov 2010 – Jul 2013) →