2011-2016 FJ Cruiser · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2009 – Oct 2010 Nov 2010 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. INSPECT CYLINDER HEAD SET BOLT

A224657E01
  1. Using a vernier caliper, measure the length of the cylinder head bolt from the seat to the end.

    Text in Illustration 
    *a
    Measurement Length

    Standard length:
    141.3 to 142.7 mm (5.56 to 5.62 in.)

    Maximum length:
    143.7 mm (5.66 in.)

    If the length is more than the maximum, replace the cylinder head bolt.

  1. A226002
    Using a vernier caliper, measure the diameter of the elongated thread at the narrowest visible area.

    Standard diameter:
    10.73 to 10.97 mm (0.422 to 0.432 in.)

    Minimum diameter:
    10.40 mm (0.409 in.)

    If the diameter is less than the minimum, replace the cylinder head bolt.

    HINT:
    If a visual check reveals no excessively thin areas, check the center of the bolt (refer to illustration) and find the area that has the smallest diameter.


2. INSPECT CYLINDER HEAD SUB-ASSEMBLY

A221108E02
  1. Using a precision straightedge and feeler gauge, measure the warpage of the surfaces which contact the cylinder block sub-assembly and manifolds.

    Text in Illustration 
    *a
    Cylinder Block Side:
    *b
    Intake Side:
    *c
    Exhaust Side:

    Standard Warpage:
    Item
    Specified Condition
    Cylinder block side
    0.05 mm (0.00197 in.)
    Intake side
    0.08 mm (0.00315 in.)
    Exhaust side
    0.08 mm (0.00315 in.)

    Maximum Warpage:
    Item
    Specified Condition
    Cylinder block side
    0.10 mm (0.00394 in.)
    Intake side
    0.10 mm (0.00394 in.)
    Exhaust side
    0.10 mm (0.00394 in.)

    If the warpage is more than the maximum, replace the cylinder head sub-assembly.

  1. Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
    If cracked, replace the cylinder head sub-assembly.


3. INSTALL CYLINDER HEAD GASKET
  1. Remove any old seal packing material and be careful not to drop any oil on the contact surfaces of the cylinder head or cylinder block.

  1. A222175E02
    Apply seal packing to a new cylinder head gasket as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing
    *b
    Gasket

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2.5 to 3.0 mm (0.0984 to 0.118 in.)

    Seal packing application range 
    A
    10 to 15 mm (0.394 to 0.591 in.)
    B
    1.25 to 1.5 mm (0.0492 to 0.0591 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head gasket within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not add engine oil within 2 hours of installation.

  1. A221095E02
    Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.

    NOTICE:
    Make sure that the gasket is installed facing the proper direction.

    Text in Illustration 
    *a
    Lot No.
    V100135
    Engine Front


4. INSTALL CYLINDER HEAD SUB-ASSEMBLY
  1. Place the cylinder head on the cylinder block.

    NOTICE:
    1. Gently place the cylinder head in order not to damage the gasket with the bottom part of the head.
    2. Make sure that no oil is on the mounting surface of the cylinder head.

    HINT:
    The cylinder head bolts are tightened in 3 progressive steps.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.

  1. Step 1:

    1. A221092E02
      Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps and in the sequence shown in the illustration.

      Torque:
      36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Step 2:

    1. Mark the front side of each cylinder head bolt head with paint.

    2. Tighten the cylinder head bolts another 90°.

  1. Step 3:

    1. Tighten the cylinder head bolts an additional 90°.

    2. Check that the paint mark is now at a 180° angle to the front.

      NOTICE:
      Thoroughly wipe clean any seal packing.


5. INSTALL NO. 2 CYLINDER HEAD GASKET
  1. Remove any old seal packing material and be careful not to drop any oil on the contact surfaces of the cylinder head or cylinder block.

  1. A222176E02
    Apply seal packing to a new cylinder head gasket as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing
    *b
    Gasket

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2.5 to 3.0 mm (0.0984 to 0.118 in.)

    Seal packing application range 
    A
    10 to 15 mm (0.394 to 0.591 in.)
    B
    1.25 to 1.5 mm (0.0492 to 0.0591 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head gasket within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not add engine oil within 2 hours of installation.

  1. A221096E02
    Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.

    NOTICE:
    Make sure that the gasket is installed facing the proper direction.

    Text in Illustration 
    *a
    Lot No.
    V100135
    Engine Front


6. INSTALL CYLINDER HEAD LH
  1. Place the cylinder head on the cylinder block.

    NOTICE:
    1. Gently place the cylinder head in order not to damage the gasket with the bottom part of the head.
    2. Make sure that no oil is on the mounting surface of the cylinder head.

    HINT:
    The cylinder head bolts are tightened in 3 progressive steps.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.

  1. Step 1:

    1. A221094E02
      Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps in the sequence shown in the illustration.

      Torque:
      36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Step 2:

    1. Mark the front side of each cylinder head bolt head with paint.

    2. Tighten the cylinder head bolts another 90°.

  1. Step 3:

    1. Tighten the cylinder head bolts an additional 90°.

    2. Check that the paint mark is now at a 180° angle to the front.

  1. A221093E02
    Tighten the 2 bolts in the order shown in the illustration.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Thoroughly wipe clean any seal packing.


7. INSTALL VALVE STEM CAP
  1. Apply a light coat of engine oil to the 24 valve stem caps.

  1. Install the 24 valve stem caps to the cylinder head sub-assembly and cylinder head LH.


8. INSTALL VALVE LASH ADJUSTER ASSEMBLY
  1. Inspect the 24 valve lash adjuster assemblies (Click here).

  1. Install the 24 valve lash adjuster assemblies to the cylinder head sub-assembly and cylinder head LH.

    NOTICE:
    Install the valve lash adjuster assemblies at the same place they were removed from.


9. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Apply engine oil to the valve lash adjuster assembly tips and valve stem cap ends.

  1. A221097E02
    Install the 24 No. 1 valve rocker arm sub-assemblies as shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve
    *4
    Valve Stem Cap


10. INSTALL CAMSHAFT BEARING CAP (for Bank 2)
  1. Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly LH and camshaft bearing caps.

  1. Install the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly to the camshaft housing sub-assembly LH.

  1. A224655
    Check the marks and numbers on the camshaft bearing caps and place each of them in the proper position facing the proper direction.

  1. A221188E01
    Temporarily tighten the 8 bolts in the sequence shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


11. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH

A221097E02
  1. Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.

    Text in Illustration 
    *1
    No, 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve
    *4
    Valve Stem Cap

  1. A221189E03
    Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    3.5 to 4.5 mm (0.138 to 0.177 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the camshaft housing sub-assembly LH within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

  1. A223640E01
    Install the camshaft housing sub-assembly LH to the cylinder head LH with the 13 bolts in the sequence shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    NOTICE:
    1. When installing the camshaft housing sub-assembly LH, it is necessary to correctly position the camshafts as shown in the illustration. Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated with a piston at TDC, valve contact will occur.
    2. If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly LH, clean the installation surfaces, and reapply seal packing.
    3. If the camshaft housing sub-assembly LH is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.
    4. Do not start the engine for at least 2 hours after installing.

  1. A221184E02
    Tighten the 8 bolts in the sequence shown in the illustration.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    NOTICE:
    Thoroughly wipe clean any seal packing.


12. INSTALL CAMSHAFT BEARING CAP (for Bank 1)
  1. Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly RH and camshaft bearing caps.

  1. Install the camshaft and No. 2 camshaft to the camshaft housing sub-assembly RH.

  1. A221190
    Check the marks and numbers on the camshaft bearing caps and place each of them in the proper position facing the proper direction.

  1. A221387E01
    Temporarily tighten the 8 camshaft bearing cap bolts in the sequence shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


13. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH

A221097E02
  1. Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.

    Text in Illustration 
    *1
    No. 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve
    *4
    Valve Stem Cap

  1. A221388E03
    Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    3.5 to 4.5 mm (0.138 to 0.177 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the camshaft housing sub-assembly RH within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

  1. A223641E01
    Install the camshaft housing sub-assembly RH and tighten the 12 bolts in the sequence shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    NOTICE:
    1. When installing the camshaft housing sub-assembly RH, it is necessary to correctly position the camshafts as shown in the illustration.
      Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated with a piston at TDC, valve contact will occur.
    2. If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly RH, clean the installation surfaces, and reapply seal packing.
    3. If the camshaft housing sub-assembly RH is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.
    4. Do not start the engine for at least 2 hours after installing.

  1. A221179E02
    Tighten the 8 bolts in the sequence shown in the illustration.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    NOTICE:
    Thoroughly wipe clean any seal packing.


14. INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY (for Bank 2)

A222171E03
  1. Install the No. 3 chain tensioner assembly to the camshaft housing sub-assembly LH with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Push in the plunger and insert a pin a of 1.0 mm (0.0394 in.) diameter into the plunger hole to hold the tensioner.

    Text in Illustration 
    *1
    Plunger
    *a
    Pin of 1.0 mm (0.0394 in.) diameter
    *b
    Push


15. INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

A227957E03
  1. Align the mark plates (yellow) with the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly LH as shown in the illustration.

    Text in Illustration 
    *1
    Mark Plate
    *a
    Timing Mark

  1. Apply a light coat of engine oil to the bolt threads and bolt-seating surface.

  1. Align the knock pin of the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear LH with the No. 2 chain sub-assembly installed.

  1. A306603E01
    Using SST to hold the hexagonal portion of each camshaft, install the 2 bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly LH.
    Text in Illustration 
    *a
    Turn
    *b
    Hold
    SST
    09922-10010  

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Remove the pin from the No. 3 chain tensioner assembly.


16. INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY (for Bank 1)

A222174E03
  1. Install the No. 2 chain tensioner assembly to the camshaft housing sub-assembly RH with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Push in the plunger and insert a pin of 1.0 mm (0.0394 in.) diameter into the plunger hole to hold the tensioner.

    Text in Illustration 
    *1
    Plunger
    *a
    Pin of 1.0 mm (0.0394 in.) diameter
    *b
    Push


17. INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

A227958E02
  1. Align the mark plates (yellow) with the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly RH as shown in the illustration.

    Text in Illustration 
    *1
    Mark Plate
    *a
    Timing Mark

  1. Apply a light coat of engine oil to the bolt threads and bolt-seating surface.

  1. Align the knock pin of the camshaft and No. 2 camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear assembly RH with the No. 2 chain sub-assembly installed.

  1. A306604E01
    Using SST to hold the hexagonal portion of each camshaft, install the 2 bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly RH.
    Text in Illustration 
    *a
    Turn
    *b
    Hold
    SST
    09922-10010  

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Remove the pin from the No. 2 chain tensioner assembly.


18. INSTALL NO. 1 CHAIN VIBRATION DAMPER

A223642
  1. Install the No. 1 chain vibration damper to the cylinder block sub-assembly and cylinder head LH with the 2 bolts.

    Torque:
    23 N*m{ 229 kgf*cm , 17 ft.*lbf }


19. INSTALL NO. 2 CHAIN VIBRATION DAMPER

A221176
  1. Install the 2 No. 2 chain vibration dampers to the cylinder head sub-assembly and cylinder head LH.


20. INSTALL CRANKSHAFT TIMING SPROCKET

A076293E02
  1. Install the crankshaft timing sprocket to the crankshaft with the sprocket facing inward as shown in the illustration.

    Text in Illustration 
    *a
    Inward


21. INSTALL NO. 1 IDLE GEAR SHAFT
  1. Apply a light coat of engine oil to the rotating surface of the No. 1 idle gear shaft.

  1. A312628E01
    Temporarily install the No. 1 idle gear shaft and No. 1 idle gear with the No. 2 idle gear shaft while aligning the knock pin of the No. 1 idle gear shaft with the knock pin groove of the cylinder block sub-assembly.
    Text in Illustration 
    *1
    No. 1 Idle Gear Shaft
    *2
    No. 1 Idle Gear
    *3
    No. 2 Idle Gear Shaft
    *4
    Knock Pin

    NOTICE:
    Make sure that the idle gear is installed facing the proper direction.

  1. Using a 10 mm hexagon wrench, tighten the No. 2 idle gear shaft.

    Torque:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }


22. INSTALL CHAIN SUB-ASSEMBLY

A223644E03
  1. Align the mark plate and timing marks as shown in the illustration and install the chain sub-assembly.

    Text in Illustration 
    *1
    Mark Plate
    *a
    Timing Mark

    HINT:
    The camshaft timing gear assembly mark plates are orange.

  1. A306606
    Do not pass the chain over the crankshaft, just temporarily place it on the crankshaft timing sprocket.

  1. A223645E02
    Turn the camshaft timing gear assembly on bank 1 counterclockwise to tighten the chain sub-assembly between the banks.
    Text in Illustration 
    *1
    Chain Plate
    *a
    When the No. 1 idle gear is reused
    *b
    Mark
    *c
    Align
    *d
    Turn

    NOTICE:
    When the idle sprocket assembly is reused, align the chain plate with the mark where the plate had been in sequence to tighten the chain sub-assembly between the banks.

  1. A223646E02
    Align the mark plate and timing marks as shown in the illustration and install the chain sub-assembly to the crankshaft timing sprocket.
    Text in Illustration 
    *1
    Mark Plate
    *a
    Timing Mark

    HINT:
    The crankshaft mark plate is yellow.

  1. Temporarily tighten the crankshaft pulley bolt.

  1. A223647E02
    Turn the crankshaft clockwise to set it to the RH cylinder block bore center line (TDC/compression).
    Text in Illustration 
    *1
    Crank Angle Sensor Plate
    *a
    RH Cylinder Block Bore Center Line
    *b
    Timing Mark


23. INSTALL CHAIN TENSIONER SLIPPER

A223730
  1. Install the chain tensioner slipper to the cylinder block sub-assembly.


24. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

A178214E04
  1. Turn the stopper plate of the tensioner clockwise and push in the plunger of the No. 1 chain tensioner assembly as shown in the illustration.

    Text in Illustration 
    *1
    Stopper Plate
    *2
    Plunger
    *a
    Push

  1. Turn the stopper plate of the tensioner counterclockwise and insert a pin of 1.27 mm (0.05 in.) diameter into the holes on the stopper plate and tensioner to fix the stopper plate in place.

  1. A095165E02
    Install the No. 1 chain tensioner assembly to the cylinder head sub-assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Remove the pin from the No. 1 chain tensioner assembly.


25. INSPECT VALVE TIMING
  1. Check the camshaft timing marks.

    NOTICE:
    1. Check each timing mark from a viewpoint directly inline with the center of the camshaft and the timing mark on each camshaft timing gear.
    2. If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.

  1. Check that each camshaft timing mark is positioned as shown in the illustration.

    A223648E05

    Text in Illustration 
    *a
    Timing Mark
    *b
    Viewpoint

    HINT:
    A182780E01
    for the intake camshaft:
    Be sure to check mark A at the point when marks B, C, and D are positioned in line. If the marks are checked from any other viewpoint, they cannot be checked correctly.

  1. If the valve timing is misaligned, reinstall the chain sub-assembly.

  1. Remove the crank pulley bolt.


26. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
(Click here)
← INSTALLATION (Nov 2010 – Jul 2013)INSTALLATION (from Aug 2014) →