2011-2016 FJ Cruiser · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Aug 2009 – Jul 2013

Versions by build date: Aug 2009 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. DISCHARGE FUEL SYSTEM PRESSURE
  1. Discharge the fuel system pressure (Click here).


2. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the service hole cover from the engine under cover.

  1. A070279E02
    Install a vinyl hose onto the drain on the radiator side.
    Text in Illustration 
    *1
    Vinyl Hose
    *2
    Tape

  1. Fix the vinyl hose with tape.

    A220213E01

    Text in Illustration 
    *1
    Radiator Cap
    *2
    Reservoir Cap
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the 2 cylinder block drain cock plugs and drain the coolant from the engine.

    NOTICE:
    If coolant is not drained from the radiator drain cock plug, cylinder block drain cock plugs and radiator reservoir, clogging in the radiator or coolant leakage from the seal of water pump may result.


3. REMOVE V-BANK COVER

  1. A221454E02
    Raise the front of the V-bank cover to disengage the 2 pins.

  1. Remove the 2 V-bank cover hooks from the bracket.

  1. Remove the V-bank cover.

    Text in Illustration 
    *1
    Pin
    *2
    Hook


4. REMOVE AIR CLEANER HOSE ASSEMBLY

  1. A226624
    Disconnect the ventilation hose and vacuum hose.

  1. Disengage the wire harness clamp.

  1. Remove the bolt.

  1. Loosen the 2 hose clamps.

  1. Remove the air cleaner hose assembly.


5. REMOVE INTAKE AIR SURGE TANK

  1. A226610
    Disconnect the No. 4 water by-pass hose.

  1. Disconnect the No. 5 water by-pass hose.

  1. A226625
    Disconnect the throttle body connector.

  1. A226749
    Disconnect the No. 1 fuel vapor feed hose.

  1. Disconnect the No. 1 vacuum switching valve connector.

  1. A226750
    Disconnect the No. 1 ventilation hose.

  1. A221464
    Disconnect the 2 heater water hose clamps.

  1. A221460
    Remove the 2 bolts and throttle body bracket.

  1. A226751
    Using a clip remover, disengage the wire harness clamp.

  1. Remove the 2 bolts and No. 1 surge tank stay.

  1. A226752
    Remove the 2 bolts and No. 2 surge tank stay.

  1. A227191
    Remove the 2 nuts.
    Text in Illustration 
    V100136
    Nut

  1. Using a 8 mm socket hexagon wrench, remove the 4 bolts and the intake air surge tank.

  1. Remove the gasket.


6. REMOVE REAR CYLINDER HEAD COVER

  1. A224695
    Remove the 3 bolts and cover.


7. DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY

  1. A223035
    Disconnect the No. 1 fuel pipe sub-assembly (Click here).

    NOTICE:
    1. Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.
    2. The fuel tube connector seals with an O-ring. Ensure that there is no damage or foreign matter on the contact surface.
    3. If the connector and the pipe are stuck, push and pull on the connector to release them while pinching the retainer. Pull the connector out of the pipe carefully.
    4. Do not use any tools.
    5. Do not bend or twist the tubes.
    6. Protect the contact surface by covering it with a plastic bag.
    7. Do not damage any of the clips. If a clip is damaged, replace it.


8. DISCONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY

  1. A223036
    Disconnect the No. 2 fuel pipe sub-assembly (Click here).

    NOTICE:
    1. Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.
    2. The fuel tube connector seals with an O-ring. Ensure that there is no damage or foreign matter on the contact surface.
    3. If the connector and the pipe are stuck, push and pull on the connector to release them while pinching the retainer. Pull the connector out of the pipe carefully.
    4. Do not use any tools.
    5. Do not bend or twist the tubes.
    6. Protect the contact surface by covering it with a plastic bag.
    7. Do not damage any of the clips. If a clip is damaged, replace it.


9. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. A223037
    Disconnect the 6 fuel injector connectors.

  1. Remove the 4 bolts and fuel delivery pipe together with the 6 fuel injectors.

    NOTICE:
    Be careful not to drop the injectors when removing the fuel delivery pipe.


10. REMOVE INTAKE MANIFOLD

  1. A221466
    Remove the 4 nuts, 6 bolts and intake manifold.

  1. Remove the 2 gaskets.

← COMPONENTS (from Aug 2014)REMOVAL (Aug 2013 – Jul 2014) →