2011-2016 FJ Cruiser · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Nov 2010 – Jul 2014

Versions by build date: Aug 2009 – Oct 2010 Nov 2010 – Jul 2014 from Aug 2014


1. REMOVE V-BANK COVER

  1. A221454E02
    Raise the front of the V-bank cover to disengage the 2 pins.

  1. Remove the 2 V-bank cover hooks from the bracket.

  1. Remove the V-bank cover.

    Text in Illustration 
    *1
    Pin
    *2
    Hook


2. REMOVE AIR CLEANER CAP AND HOSE

  1. A227193
    Disconnect the MAF meter connector.

  1. Disengage the 4 wire harness clamps.

  1. Disconnect the ventilation hose and vacuum hose.

  1. Remove the bolt.

  1. Loosen the No. 1 air cleaner hose clamp.

  1. Release the 4 hinges.

  1. Remove the air cleaner cap and hose.


3. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.


4. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

  1. A226753
    Remove the 3 bolts and the air cleaner case sub-assembly.


5. REMOVE FRONT FENDER APRON SEAL LH

A223333
  1. Remove the 5 clips and fender apron seal.


6. REMOVE FRONT FENDER APRON SEAL RH

A223336
  1. Remove the 4 clips and fender apron seal.


7. REMOVE NO. 1 FENDER APRON TO FRAME SEAL LH

A223335
  1. Remove the 5 clips and frame seal.


8. REMOVE NO. 1 FENDER APRON TO FRAME SEAL RH

A223337
  1. Remove the 5 clips and frame seal.


9. REMOVE EXHAUST PIPE STOPPER BRACKET

  1. A129939
    Remove the 2 bolts, then remove the exhaust pipe stopper bracket.


10. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY
  1. Disconnect the heated oxygen sensor connector.

  1. A225941
    Remove the 2 bolts and 2 nuts.

  1. Disconnect the exhaust pipe support and remove the front No. 2 exhaust pipe.

  1. Remove the 2 gaskets.


11. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Disconnect the heated oxygen sensor connector.

  1. A225942
    Remove the 2 bolts and 2 compression springs.

  1. Remove the 2 nuts and the front exhaust pipe.

  1. Remove the 2 gaskets.


12. REMOVE MANIFOLD STAY

A221486
  1. Remove the 3 bolts and manifold stay.


13. SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY (for RHD)

  1. A188038E01
    Mark matchmarks on the power steering gear assembly and No. 2 steering intermediate shaft.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the 2 bolts from the steering yoke.

  1. Slide the steering sliding yoke up and separate it from the No. 2 steering intermediate shaft sub-assembly


14. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

A225631
  1. Remove the 3 bolts and heat insulator.


15. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

A222090
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the 6 nuts, manifold and gasket.


16. REMOVE AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

  1. A223682E02
    Using SST, remove the sensor.
    SST
    09224-00010  


17. REMOVE NO. 2 MANIFOLD STAY

A222091
  1. Remove the 3 bolts and No. 2 manifold stay.


18. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

A221484
  1. Remove the 3 bolts and heat insulator.


19. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

A222093
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the 6 nuts, manifold and gasket.


20. REMOVE AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

  1. A223684E02
    Using SST, remove the sensor.
    SST
    09224-00010  

← REMOVAL (Aug 2009 – Oct 2010)REMOVAL (from Aug 2014) →