2011-2016 FJ Cruiser · Service Manual ENGINE

P144C Open in Secondary Air Injection System Heater Control Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

DESCRIPTION

The ECM operates the AIR PMP HTR relay which causes the air pump heater (AIR PMP HTR) to operate.
DTC No.
DTC Detection Condition
Trouble Area
P144C
Open or short in the AIR PMP HTR relay circuit for 5 seconds (1 trip detection logic).
  1. Open or short in AIR PMP HTR relay circuit
  2. AIR PMP HTR relay
  3. ECM
P144D
Open or short in the AIR PMP HTR relay circuit for 5 seconds (1 trip detection logic).
  1. Open or short in AIR PMP HTR relay circuit
  2. AIR PMP HTR relay
  3. ECM

MONITOR DESCRIPTION

These DTCs are designed to detect a malfunction in the AIR PMP HTR relay circuit. When the system is normal, the battery voltage is applied to terminal HAI1 of the ECM while the AIR PMP HTR relay is turned off, and the battery voltage is not applied to terminal HAI1 of the ECM while the AIR PMP HTR relay is turned on. The ECM illuminates the MIL and stores a DTC when either one of the following conditions is detected.
  1. The battery voltage is not applied to terminal HAI1 while the AIR PMP HTR relay is off.
  2. The battery voltage is applied to terminal HAI1 while the AIR PMP HTR relay is on.

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on.
  6. Wait for 10 seconds.
  7. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Air Pump Heater.
  8. Activate the air pump heater for 10 seconds or more.

    HINT:
    1. The active test activates the air pump heater for up to 60 seconds.
    2. To protect the air pump heater, do not perform this test more than 4 times in a row.

  9. Enter the following menus: Powertrain / Engine and ECT / DTC.
  10. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P144C or P144D.
  13. Check the DTC judgment result.
    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.


WIRING DIAGRAM

Refer to DTC P0412 (Click here).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT AIR PMP HTR RELAY
A232574E01
  1. Remove the AIR PMP HTR relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE AIR PMP HTR RELAY
OK


2. CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR PMP HTR RELAY)
  1. Remove the AIR PMP HTR relay from the engine room relay block.

  1. Turn the ignition switch to ON.

  1. A287418E01
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (AIR PMP HTR relay holder) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    AIR PMP HTR Relay Holder



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (ECM - AIR PMP HTR RELAY)
  1. Remove the AIR PMP HTR relay from the engine room relay block.

  1. Disconnect the B49 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (AIR PMP HTR relay holder) - B49-20 (HAI1)
    Always
    Below 1 Ω
    1 (AIR PMP HTR relay holder) or B49-20 (HAI1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0724 Brake Switch "B" Circuit High (from Nov 2010)P1603 Engine Stall History (+ P1605) (Aug 2009 – Oct 2010) →