2011-2016 FJ Cruiser · Service Manual ENGINE

P2109 Throttle / Pedal Position Sensor "A" Minimum Stop Performance

Diagnostic trouble codes · Vehicles built Aug 2012 – Oct 2012

Versions by build date: Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Oct 2012 Nov 2012 – Jul 2014 from Aug 2014

DESCRIPTION

The idling speed is controlled by the Electronic Throttle Control System (ETCS).
The ETCS is comprised of a throttle actuator, which operates the throttle valve, and a throttle position sensor, which detects the opening amount of the throttle valve.
The ECM controls the throttle actuator to adjust the throttle valve opening amount so that the idling speed is maintained at the target idling speed.
DTC No.
DTC Detection Condition
Trouble Area
P2109
Either condition is met:
  1. With the mass air flow meter normal and atmospheric pressure 85 kPa (638 mmHg) or more (elevation 1400 m (4592 ft.) or less), when the engine coolant temperature is 45°C (113°F) or less at engine start, the engine is warmed up and conditions for ISC learning are met, the ISC learning value is approximately 3 times larger than normal even though the intake manifold pressure when idling is normal (5 trip detection logic).
  2. With the mass air flow meter normal and atmospheric pressure 85 kPa (638 mmHg) or more (elevation 1400 m (4592 ft.) or less), when the ignition switch has been turned to ON for 1 hour or more, the engine is warmed up, conditions for ISC learning are met and the vehicle has been driven at a speed of 30 km/h (19 mph) or more at least once, the ISC learning value is approximately 3 times larger than normal even though the intake manifold pressure when idling is normal (5 trip detection logic).
Throttle with motor body assembly

MONITOR DESCRIPTION

If there are deposits in the throttle valve, the necessary ISC flow rate for idling is maintained using the ISC learning value and feedback as a decrease in the ISC flow rate may cause engine stall or unstable idling. The ECM stores this DTC if the ISC learning value approaches its limit.

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
  1. Since a pending DTC is not stored for this DTC, it takes time to confirm whether the malfunction has been successfully repaired by checking for this DTC. When confirming whether the malfunction has been successfully repaired, compare "ISC Learning Value" recorded in the freeze frame data with "ISC Learning Value" in the Data List after repairs have been made to save time.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2109)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    Only DTC P2109 is output
    A
    DTC P2109 and other DTCs are output
    B

HINT:
If any DTCs other than P2109 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. CHECK FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the tester, check "ISC Learning Value" in the freeze frame data (Click here).

    HINT:
    Be sure to confirm "ISC Learning Value" in the freeze frame data as it is used when confirming whether the malfunction has been successfully repaired.


NEXT


3. REMOVE FOREIGN OBJECT (CLEAN THROTTLE WITH MOTOR BODY ASSEMBLY)
A218150E02
  1. Clean off any deposits from the inside of the throttle with motor body assembly.

    1. Push open the throttle valve and wipe off any carbon from the valve and bore using a cloth soaked in non-residue solvent.

NOTICE:
  1. Make sure that the cloth or your fingers do not get caught in the valve.
  2. Make sure that foreign matter does not enter the throttle valve.
  3. Do not directly apply non-residue solvent to the throttle body with motor assembly or wash the throttle body with motor assembly. Cleaning solvent may leak into the motor from the shaft and cause problems such as rust or valve movement problems.
  4. If there is coating material on the edge of the valve, be careful not to remove it.
  5. Push the throttle valve open gently with your finger and check that the throttle valve moves smoothly.


NEXT


4. READ VALUE USING INTELLIGENT TESTER (ISC LEARNING VALUE)
  1. Remove the EFI and ETCS fuses at the same time, wait 60 seconds or more, and then reinstall the fuses to reset the ISC learning value.

  1. Start the engine and fully warm it up.

  1. Leave the vehicle idling for 3 minutes or more and check that the engine speed is at the standard idling speed.

    HINT:
    Check the freeze frame data and make sure that the vehicle conditions are the same as when the DTC was stored.

  1. Using the intelligent tester, confirm "ISC Learning Value".

OK:
The value is half of "ISC Learning Value" recorded in the freeze frame data or less.



NG
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
OK

END


← P2109 Throttle / Pedal Position Sensor "A" Minimum Stop Performance (Aug 2011 – Jul 2012)P2109 Throttle / Pedal Position Sensor "A" Minimum Stop Performance (Nov 2012 – Jul 2014) →