Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



C213108E05

HINT:
The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E78-24 (BATT) - B49-12 (E1)
L - BR
Battery (for measuring the battery voltage and for the ECM memory)
Always
11 to 14 V
B49-23 (+BM) - B49-12 (E1)
R-G - BR
Power source of throttle motor
Always
11 to 14 V
E77-21 (IGSW) - B49-12 (E1)
B-O - BR
Ignition switch
Ignition switch ON
11 to 14 V
E78-22 (+B) - B49-12 (E1)
B - BR
Power source of ECM
Ignition switch ON
11 to 14 V
E78-23 (+B2) - B49-12 (E1)
B - BR
Power source of ECM
Ignition switch ON
11 to 14 V
B48-19 (OC1+) - B48-20 (OC1-)
G-Y - L-B
Camshaft timing oil control valve (OCV) assembly (for intake side of bank 1)
Idling
Pulse generation
(See waveform 1)
B47-19 (OC2+) - B47-20 (OC2-)
L-W - L-R
Camshaft timing oil control valve (OCV) assembly (for intake side of bank 2)
Idling
Pulse generation
(See waveform 1)
B48-21 (OE1+) - B48-22 (OE1-)
G-B - B-R
Camshaft timing oil control valve (OCV) assembly (for exhaust side of bank 1)
Idling
Pulse generation
(See waveform 1)
B47-21 (OE2+) - B47-22 (OE2-)
B-W - R-L
Camshaft timing oil control valve (OCV) (for exhaust side of bank 2)
Idling
Pulse generation
(See waveform 1)
E78-9 (MREL) - B49-12 (E1)
W-G - BR
EFI relay
Ignition switch ON
11 to 14 V
B47-15 (VCV1) - B48-8 (ETHW)
P-L - W-R
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
B47-16 (VCV2) - B48-7 (ETHA)
LG-B - W-R*3
LG-B - W-G*4
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
B48-14 (VG) - B48-13 (E2G)
G - B-Y
Mass air flow meter
Idling, Shift lever position P or N (neutral), A/C switch OFF
0.5 to 3.0 V
B48-15 (THA) - B48-7 (ETHA)
P - W-R*3
P - W-G*4
Intake air temperature sensor
Idling, Intake air temperature 20°C (68°F)
0.5 to 3.4 V
B49-17 (THW) - B48-8 (ETHW)
B - W-R
Engine coolant temperature sensor
Idling, Engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
B49-15 (VTA1) - B49-14 (ETA)
B-L - W
Throttle position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON, Accelerator pedal fully depressed
3.2 to 4.8 V
B49-16 (VTA2) - B49-14 (ETA)
G-W - W
Throttle position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
2.1 to 3.1 V
Ignition switch ON, Accelerator pedal fully depressed
4.6 to 5.0 V
E77-6 (VPA) - E77-3 (EPA)
W-R - LG-B
Accelerator pedal position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON, Accelerator pedal fully depressed
2.6 to 4.5 V
E77-5 (VPA2) - E77-1 (EPA2)
R-B - V-W
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
1.2 to 2.0 V
Ignition switch ON, Accelerator pedal fully depressed
3.4 to 4.75 V
E77-4 (VCPA) - E77-3 (EPA)
G - LG-B
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.5 V
E77-2 (VCP2) - E77-1 (EPA2)
W-L - V-W
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.5 V
B49-13 (VCTA) - B49-14 (ETA)
R - W
Power source of throttle position sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
B50-17 (HA1A) - B50-16 (E04)
B50-19 (HA2A) - B50-18 (E05)
R-L - W-B
B-W - W-B
Air fuel ratio sensor heater
Idling with warm engine
Pulse generation
(See waveform 2)
Ignition switch ON
11 to 14 V
B49-1 (A1A+) - B49-12 (E1)
R - BR
Air fuel ratio sensor
Ignition switch ON
3.3 V*1
B49-7 (A2A+) - B49-12 (E1)
Y - BR
Air fuel ratio sensor
Ignition switch ON
3.3 V*1
B49-2 (A1A-) - B49-12 (E1)
G - BR
Air fuel ratio sensor
Ignition switch ON
2.9 V*1
B49-8 (A2A-) - B49-12 (E1)
L - BR
Air fuel ratio sensor
Ignition switch ON
2.9 V*1
B50-12 (HT1B) - B50-11 (E03)
B50-13 (HT2B) - B50-11 (E03)
B - W-B
GR - W-B
Heated oxygen sensor heater
Idling
Below 3.0 V
Ignition switch ON
11 to 14 V
B47-2 (OX1B) - B47-1 (EX1B)
B47-4 (OX2B) - B47-3 (EX2B)
W - B
P - L
Heated oxygen sensor
Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
Pulse generation
(See waveform 3)
B50-6 (#10) - B50-14 (E01)
B50-1 (#20) - B50-14 (E01)
B50-7 (#30) - B50-14 (E01)
B50-2 (#40) - B50-14 (E01)
B50-8 (#50) - B50-14 (E01)
B50-3 (#60) - B50-14 (E01)
R-L - BR
G - BR
R - BR
W - BR
Y - BR
L - BR
Fuel Injector assembly
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(See waveform 4)
B48-11 (KNK1) - B48-12 (EKNK)
B - W
Knock sensor
Engine speed maintained at 4000 rpm after warming up engine
Pulse generation
(See waveform 5)
B48-5 (KNK2) - B48-6 (EKN2)
G - R
Knock sensor
Engine speed maintained at 4000 rpm after warming up engine
Pulse generation
(See waveform 5)
B47-9 (VV1+) - B47-10 (VV1-)
R - G
Variable valve timing (VVT) sensor (for intake side of bank 1)
Idling
Pulse generation
(See waveform 6)
B47-12 (VV2+) - B47-11 (VV2-)
Y - L
Variable valve timing (VVT) sensor (for intake side of bank 2)
Idling
Pulse generation
(See waveform 6)
B47-13 (EV1+) - B47-14 (EV1-)
B-Y - R-B
Variable valve timing (VVT) sensor (for exhaust side of bank 1)
Idling
Pulse generation
(See waveform 7)
B47-18 (EV2+) - B47-17 (EV2-)
GR - P
Variable valve timing (VVT) sensor (for exhaust side of bank 2)
Idling
Pulse generation
(See waveform 7)
B47-6 (NE+) - B47-5 (NE-)
B - W
Crankshaft position sensor
Idling
Pulse generation
(See waveform 6, 7)
B49-24 (IGT1) - B49-12 (E1)
B49-25 (IGT2) - B49-12 (E1)
B49-26 (IGT3) - B49-12 (E1)
B49-27 (IGT4) - B49-12 (E1)
B49-28 (IGT5) - B49-12 (E1)
B48-25 (IGT6) - B49-12 (E1)
Y-R - BR
G - BR
B-W - BR
Y-G - BR
GR - BR
L - BR
Ignition coil with igniter (ignition signal)
Idling
Pulse generation
(See waveform 8)
B49-6 (IGF1) - B49-12 (E1)
W-R - BR
Ignition coil with igniter (ignition confirmation signal)
Ignition switch ON
4.5 to 5.5 V
Idling
Pulse generation
(See waveform 8)
B49-18 (PRG) - B49-12 (E1)
G-Y - BR
Purge VSV
Ignition switch ON
11 to 14 V
Idling, during purge control
Pulse generation
(See waveform 9)
E78-18 (SPD) - B49-12 (E1)
V-R - BR
Speed signal from combination meter assembly
Driving at 20 km/h (12 mph)
Pulse generation
(See waveform 10)
E77-10 (STA) - B49-12 (E1)
V-R - BR
Starter signal
Cranking
11 to 14 V
E77-18 (STP) - B49-12 (E1)
G-Y - BR
Stop light switch
Brake pedal depressed
7.5 to 14 V
Brake pedal released
Below 1.5 V
E78-8 (ST1-) - B49-12 (E1)
R-L - BR
Stop light switch (opposite to STP terminal)
Ignition switch ON, Brake pedal depressed
Below 1.5 V
Ignition switch ON, Brake pedal released
7.5 to 14 V
B48-2 (NSW)*2 - B49-12 (E1)
L-Y - BR
Park/Neutral position switch assembly
Ignition switch ON, Shift lever position in P or N
Below 3.0 V
Ignition switch ON, Shift lever position other than P and N
11 to 14 V
B50-20 (M+) - B50-10 (ME01)
P - W-B
Throttle motor
Idling with warm engine
Pulse generation
(See waveform 11)
B49-29 (M-) - B50-10 (ME01)
L - W-B
Throttle motor
Idling with warm engine
Pulse generation
(See waveform 12)
E77-8 (FC)*4 - B49-12 (E1)
GR-B - BR
Fuel pump control
Stop engine and ignition switch to ON
11 to 14 V
E78-3 (FPC) - B49-12 (E1)
G - BR
Fuel pump control
Stop engine and ignition switch to ON
Below 1.5 V
E78-13 (W) - B49-12 (E1)
R-B - BR
MIL
Ignition switch ON
Below 3.0 V
Idling
11 to 14 V
E78-11 (ELS1) - B49-12 (E1)
Y-B - BR
Electric load
Taillight switch OFF
0 to 1.5 V
Taillight switch ON
11 to 14 V
E78-10 (ELS2) - B49-12 (E1)
Y-G - BR
Electric load
Voltage inverter OFF
0 to 1.5 V
Voltage inverter ON
11 to 14 V
E77-28 (TC) - B49-12 (E1)
P-L - BR
Terminal TC of DLC 3
Ignition switch ON
11 to 14 V
E77-29 (TACH) - B49-12 (E1)
B-W - BR
Engine speed
Idling
Pulse generation
(See waveform 13)
B48-16 (PSP) - B49-12 (E1)
V - BR
Power steering oil pressure switch (sensor)
Ignition switch ON
0.5 to 4.5 V
E77-19 (VPMP) - B49-12 (E1)
R-G - BR
Vent valve
(built into canister pump module)
Ignition switch ON
11 to 14 V
E77-7 (MPMP) - B49-12 (E1)
B-R - BR
Leak detection pump
(built into canister pump module)
Leak detection pump OFF
0 to 3 V
Leak detection pump ON
11 to 14 V
B48-1 (PPMP) - B48-8 (ETHW)
R - W-R
Canister pressure sensor
(built into canister pump module)
Ignition switch ON
3 to 3.6 V
E77-26 (DI)*4 - B49-12 (E1)
GR- BR
Fuel pump control
Stop engine and ignition switch to ON
0 to 3.0 V
E77-32 (CANH) - B49-12 (E1)
LG-R - BR
CAN communication line
Stop engine and ignition switch to ON
Pulse generation
(See waveform 14)
E77-31 (CANL) - B49-12 (E1)
LG-B - BR
CAN communication line
Stop engine and ignition switch to ON
Pulse generation
(See waveform 15)
B47-26 (AIRV)*3 - B49-12 (E1)
P - BR
Emission control valve set for secondary air injection system
Ignition switch ON
11 to 14 V
B48-23 (AIRP)*3 - B49-12 (E1)
R-G - BR
Air pump control
Ignition switch ON
11 to 14 V
B48-30 (AIDI)*3 - B49-12 (E1)
G - BR
Diagnostic information signal for secondary air injection system
Secondary air injection system operating
Pulse generation
(See waveform 16)
B49-21 (AIR1)*3 - B49-12 (E1)
L - BR
No. 2 emission control valve set for secondary air injection system
Ignition switch ON
11 to 14 V
E78-1 (AIP)*3 - B48-7 (ETHA)
G-Y - W-R
Secondary air injection system pressure signal
Ignition switch ON
3.0 to 3.6 V
E78-2 (AIP2)*3 - B48-7 (ETHA)
R - W-R
Secondary air injection system pressure signal
Ignition switch ON
3.0 to 3.6 V
B49-20 (HAI1)*3 - B49-12 (E1)
W - BR
Air pump heater for secondary air injection system
Air heater operating
11 to 14 V
  1. *1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.
  2. *2: for Automatic Transmission Models
  3. *3: w/ Secondary Air Injection System
  4. *4: w/o Secondary Air Injection System

WAVEFORM 1
A093229E40
Camshaft Timing Oil Control Valve (OCV) Assembly 
ECM Terminal Name
Between OC1+ and OC1- or OC2+ and OC2-
OE1+ and OE1- or OE2+ and OE2-
Tester Range
5 V/DIV, 1 ms/DIV
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 2
A172534E04
Air Fuel Ratio Sensor Heater 
ECM Terminal Name
CH1: Between HA1A and E04
CH2: Between HA2A and E05
Tester Range
5 V/DIV, 10 ms/DIV
Condition
Idling with warm engine

HINT:
The wavelength varies in accordance with the engine operating condition.


WAVEFORM 3
A088863E55
Heated Oxygen Sensor 
ECM Terminal Name
Between OX1B and EX1B or OX2B and EX2B
Tester Range
200 mV/DIV, 200 ms/DIV
Condition
Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

HINT:
In the Data List, item O2S B1S2 or O2S B2S2 shows the ECM input values from the heated oxygen sensor.


WAVEFORM 4
G035622E12
Fuel Injector assembly 
ECM Terminal Name
Between #10 (to 60) and E01
Tester Range
30 V/DIV, 20 ms/DIV
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 5
A085286E70
Knock Sensor 
ECM Terminal Name
Between KNK1 and EKNK or KNK2 and EKN2
Tester Range
1 V/DIV, 1 ms/DIV
Condition
Engine speed maintained at 4000 rpm after warming up engine

HINT:
  1. The wavelength becomes shorter as the engine speed increases.
  2. The waveforms and amplitudes displayed on the tester differ slightly depending on the vehicle.


WAVEFORM 6
A122767E13
Crankshaft Position Sensor and VVT Sensor for Intake Side 
ECM Terminal Name
CH1: Between NE+ and NE-
CH2: Between VV1+ and VV1- or VV2+ and VV2-
Tester Range
5 V/DIV, 20 ms/DIV
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 7
A122768E11
VVT Sensor for Exhaust Side 
ECM Terminal Name
CH1: Between NE+ and NE-
CH2: Between EV1+ and EV1- or EV2+ and EV2-
Tester Range
5 V/DIV, 20 ms/DIV
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 8
G035664E13
Igniter IGT Signal (from ECM to Igniter) and Igniter IGF Signal (from Igniter to ECM) 
ECM Terminal Name
CH1: Between IGT (1 to 6) and E1
CH2: Between IGF1 and E1
Tester Range
2 V/DIV, 20 ms/DIV
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 9
A226251E01
Purge VSV 
ECM Terminal Name
Between PRG and E1
Tester Range
10 V/DIV, 50 ms/DIV
Condition
Idling, during purge control

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 10
A093224E28
Vehicle Speed Signal 
ECM Terminal Name
Between SPD and E1
Tester Range
2 V/DIV, 20 ms/DIV
Condition
Driving at 20 km/h (12 mph)

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 11
A208000E29
Throttle Actuator Positive Terminal 
ECM Terminal Name
Between M+ and ME01
Tester Range
5 V/DIV, 1 ms/DIV
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 12
A245848E28
Throttle Actuator Negative Terminal 
ECM Terminal Name
Between M- and ME01
Tester Range
5 V/DIV, 1 ms/DIV
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 13
A093225E35
Engine Speed Signal 
ECM Terminal Name
Between TACH and E1
Tester Range
5 V/DIV, 10 ms/DIV
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 14
A086154E51
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANH and E1
Tester Range
1 V/DIV, 10 μs/DIV
Condition
Stop engine and ignition switch to ON

HINT:
The wavelength varies depending on the CAN communication signal.


WAVEFORM 15
A086155E47
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANL and E1
Tester Range
1 V/DIV, 10 μs/DIV
Condition
Stop engine and ignition switch to ON

HINT:
The wavelength varies depending on the CAN communication signal.


WAVEFORM 16
A255990E04
Terminal DI of Air Injection Control Driver 
ECM Terminal Name
Between AIDI and E1
Tester Range
5 V/DIV, 50 ms/DIV
Condition
Secondary air injection system operating

HINT:
The wavelength changes when the air injection control driver detects malfunctions in the secondary air injection system (Click here).