Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P1613    Secondary Air Injection System Driver

for Preparation Click here


DESCRIPTION

Refer to DTC P0412 .

DTC No.
DTC Detection Condition
Trouble Area
P1613
One of the following conditions (1), (2), (3) or (4) is met:
(1) Both of the following conditions are met for 3 seconds or more (1 trip detection logic):
  1. Diagnostic signal from the air injection control driver has a duty cycle of 1% or more, and 10% or less.
  2. Battery voltage is 8 V or higher.
(2) Both conditions are met for 3 seconds or more (1 trip detection logic):
  1. Diagnostic signal from the air injection control driver has a duty cycle of 30%.
  2. Battery voltage is 8 V or higher.
(3) Both of the following conditions are met for 3 seconds or more (1 trip detection logic):
  1. Diagnostic signal from the air injection control driver has a duty cycle of 49%.
  2. Battery voltage is 8 V or higher.
(4) Both of the following conditions are met for 3 seconds or more (1 trip detection logic):
  1. Diagnostic signal from the air injection control driver is 91% or more, and 99% or less.
  2. Battery voltage is 8 V or higher.
  1. Air injection control driver
  2. Open in air injection control driver ground circuit
All of the following conditions are met for 3 seconds or more (1 trip detection logic):
  1. Both of the air pump assembly or emission control valve set is not operating.
  2. Diagnostic signal from the air injection control driver is 70% or more, and 90% or less.
  3. Battery voltage is 8 V or higher.
  1. Air injection control driver
  2. ECM
All of the following conditions are met for 3 seconds or more (1 trip detection logic):
  1. Both of the air pump assembly and emission control valve set are operating
  2. Diagnostic signal from the air injection control driver has a duty cycle of 0%
  3. Battery voltage is 8 V or higher.
  1. Short in diagnostic information signal circuit (Air injection control driver - ECM)
  2. Open or short in air pump assembly and emission control valve set command signal circuit (Air injection control driver - ECM)
  3. Open in air injection control driver ground circuit
  4. Air injection control driver
  5. ECM
Both conditions met for 3 seconds or more (1 trip detection logic):
  1. Diagnostic signal from the air injection control driver has a duty cycle of 100%.
  2. Battery voltage is 8 V or higher.
  1. Open or short in air injection control driver +B circuit
  2. Open in diagnostic information signal circuit (Air injection control driver - ECM)
  3. Air injection control driver
  4. ECM

MONITOR DESCRIPTION

This DTC indicates an open or short circuit in the circuit containing the air pump assembly of the secondary air injection system. The air injection control driver performs diagnosis of the air pump assembly, emission control valve set and itself, and sends the results of this diagnosis to the ECM as a duty signal. When the ECM receives a signal indicating a malfunction in the air pump assembly, emission control valve set or air injection control driver, it immediately illuminates the MIL and stores a DTC.

MONITOR STRATEGY


Related DTCs
P1613: Secondary air injection system air injection control driver circuit range check
Required Sensors/Components (Main)
Air injection control driver
Required Sensors/Components (Related)
Emission control valve set
Frequency of Operation
Once per driving cycle
Duration
3 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Case 1 and 4 
Monitor runs whenever following DTCs not stored
None
Battery voltage
8 V or higher
Ignition switch
ON
Starter
OFF

Case 2 
Monitor runs whenever following DTCs not stored
None
Either a or b met:
-
a. Command to air pump
OFF
b. Command to emission control valve
OFF
Battery voltage
8 V or higher
Ignition switch
ON
Starter
OFF

Case 3 
Monitor runs whenever following DTCs not stored
None
Following conditions (a) and (b) met
-
a. Command to air pump
ON
b. Command to emission control valve
ON
Battery voltage
8 V or higher
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


Case 1 
One of following conditions met:
A, B, C or D
A. Diagnostic signal duty ratio from air injection control driver
1% or more, and 10% or less
B. Diagnostic signal duty ratio from air injection control driver
30%
C. Diagnostic signal duty ratio from air injection control driver
49%
D. Diagnostic signal duty ratio from air injection control driver
91% or more, and 99% or less

Case 2 
Diagnostic signal duty ratio from air injection control driver
70% or more, and 90% or less

Case 3 
Diagnostic signal duty ratio from air injection control driver
0%

Case 4 
Diagnostic signal duty ratio from air injection control driver
100%

COMPONENT OPERATING RANGE


Diagnostic signal duty ratio from air injection control driver
70% or more, and 90% or less when secondary air injection system operating.
0% when secondary air injection system not operating.

CONFIRMATION DRIVING PATTERN

NOTICE:
  1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
  2. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
  3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
  4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  1. Start the engine and warm it up.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  7. Turn the ignition switch off and wait for at least 30 seconds.
  8. Turn the ignition switch to ON and turn the Techstream on.
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
  10. Start the engine after the Techstream initialization is finished.
  11. Perform the System Check operation by pressing Next.
  12. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
  13. Enter the following menus: Powertrain / Engine and ECT / Trouble codes.
  14. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  15. After Secondary Air Injection Check is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  16. Input the DTC: P1613.
  17. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  18. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If no permanent DTC is output, the system is normal.
    2. If a permanent DTC is output, the system is malfunctioning.

  19. Turn the ignition switch off.

WIRING DIAGRAM

Refer to DTC P0412 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. By using the Techstream to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK AIR INJECTION CONTROL DRIVER (POWER SOURCE CIRCUIT)
A200902E58
  1. Disconnect the air injection control driver connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A37-5 (+B) - Body ground
    Ignition switch ON
    11 to 14 V (near battery voltage)

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Injection Control Driver)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - ECM, BODY GROUND)
  1. Disconnect the B48 and B47 ECM connectors.

  1. Disconnect the A37 air injection control driver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B48-23 (AIRP) - A37-4 (SIP)
    Always
    Below 1 Ω
    B47-26 (AIRV) - A37-3 (SIV)
    Always
    Below 1 Ω
    B48-30 (AIDI) - A37-2 (DI)
    Always
    Below 1 Ω
    A37-1 (E) - Body ground
    Always
    Below 1 Ω
    B48-23 (AIRP) or A37-4 (SIP) - Body ground
    Always
    10 kΩ or higher
    B47-26 (AIRV) or A37-3 (SIV) - Body ground
    Always
    10 kΩ or higher
    B48-30 (AIDI) or A37-2 (DI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE)
A200902E59
  1. Disconnect the air injection control driver connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A37-2 (DI) - A37-1 (E)
    Ignition switch ON
    11 to 14 V (near battery voltage)

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Injection Control Driver)



NG
REPLACE ECM (Click here)
OK


4.PERFORM SECONDARY AIR INJECTION SYSTEM CHECK


    A229922E38
  1. Disconnect the air injection control driver connector.

  1. Connect terminals DI and SIV of the wire harness connector for the air injection control driver.
    Text in Illustration 
    *1
    Air Injection Control Driver
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Air Injection Control Driver)

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system forced operation while the engine is idling.

  1. Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is ON and OFF.

  1. Turn the ignition switch off.

    NOTICE:
    1. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    A37-3 (SIV) - A37-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    A37-3 (SIV) - A37-1 (E)
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V



    A229922E39
  1. Connect terminals DI and SIP of the wire harness connector for the air injection control driver.
    Text in Illustration 
    *1
    Air Injection Control Driver
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Air Injection Control Driver)

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system forced operation while the engine is idling.

  1. Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is ON and OFF.

  1. Turn the ignition switch off.

    NOTICE:
    1. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    A37-4 (SIP) - A37-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    A37-4 (SIP) - A37-1 (E)
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V



NG
REPLACE ECM (Click here)
OK


5.REPLACE AIR INJECTION CONTROL DRIVER
  1. Replace the air injection control driver (Click here).


NEXT


6.CHECK WHETHER DTC OUTPUT RECURS
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read pending DTCs.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    Other DTCs are output
    B

  1. Turn the ignition switch off.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



B
REPLACE ECM (Click here)
A

END