Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0560    System Voltage

for Preparation Click here


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0560
Open in ECM back up power source circuit
(1 trip detection logic)
  1. Open in back up power source circuit
  2. Battery
  3. Battery terminals
  4. EFI fuse
  5. ECM

HINT:
If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly cleared.


MONITOR STRATEGY


Related DTCs
P0560: ECM system voltage
Required Sensors/Components (Main)
ECM
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
3 seconds
MIL Operation
Immediate (MIL illuminated after next engine start)
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None

TYPICAL MALFUNCTION THRESHOLDS


Continuous battery voltage
Less than 3.5 V
Stand-by RAM
Initialized

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Wait 5 seconds or more.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  8. Read DTCs.

    HINT:
    1. If a DTC is output, the system is malfunctioning.
    2. If a DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0560.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the judgment result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A164743E12


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
  1. Disconnect the ECM connector.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the cable from the positive (+) battery terminal.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    E78-24 (BATT) - Battery positive terminal
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    E78-24 (BATT) or Battery positive terminal - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the cable from the positive (+) battery terminal.

  1. Reconnect the cable from the negative (-) battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT BATTERY
  1. Check that the battery is not depleted .

    OK:
    Battery is not depleted.



NG
REPAIR OR REPLACE BATTERY
OK


3.CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded.



NG
REPAIR OR REPLACE BATTERY TERMINAL
OK


4.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0560 is output
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE ECM (Click here)