STEERING PAD > DISPOSAL |
| 1. DISPOSE OF STEERING PAD (WHEN INSTALLED IN VEHICLE) |
![]() |
Check the function of SST.
![]() |
Connect SST to the battery.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) terminal.
![]() |
Check the function of SST.
Press the SST activation switch, and check that the LED of the SST activation switch comes on.
Disconnect SST from the battery.
Precaution (Click here).
Disconnect the cable from the negative battery terminal.
![]() |
Remove the lower steering column cover.
While turning the steering wheel assembly to the right and left, remove the 3 screws and the lower steering column cover.
Install SST.
![]() |
Disconnect the airbag connector (yellow colored one) from the spiral cable.
![]() |
Connect the SST connector to the airbag connector of the spiral cable.
![]() |
Move SST at least 10 m (33 ft) away from the vehicle.
Securing enough clearance for the SST wire harness in the side window, close all doors and windows of the vehicle.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) terminal.
Deploy the airbag.
Check that no one is inside the vehicle or within a 10 m (33 ft) radius of the vehicle.
Press the SST activation switch and deploy the airbag.
| 2. DISPOSE OF STEERING PAD (WHEN NOT INSTALLED IN VEHICLE) |
![]() |
Check the function of SST.
![]() |
Connect SST to the battery.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of the SST to the negative (-) terminal.
![]() |
Check the function of SST.
Press the SST activation switch, and check that the LED of the SST activation switch comes on.
Disconnect SST from the battery.
Remove the steering pad (Click here).
![]() |
Using a service-purpose wire harness for the vehicle, tie down the steering pad to the disc wheel.
| Area | Measurement |
| A | 1.25 mm2 or more (0.0019 in.2 or more) |
![]() |
Install the 2 bolts with washers into the 2 bolt holes on the steering pad.
| Area | Specification |
| L | 35.0 mm (1.378 in.) |
| M | 6.0 mm (0.236 in.) |
| Pitch | 1.0 mm (0.039 in.) |
![]() |
After connecting SST below to each other, connect them to the steering pad.
![]() |
Using 3 wire harnesses, wind wire harness at least 2 times each around the bolts installed on the left and right sides of the steering pad.
![]() |
Face the airbag deployment side of the steering pad upward on top of a tire and wheel set. Separately tie the left and right sides of the steering pad to the disc wheel through the hub nut holes. Position the SST connector so that it hangs downward through the hub hole in the disc wheel.
![]() |
Install the SST.
Connect the SST connector.
![]() |
Move SST at least 10 m (33 ft) away from the airbag tied down to the tire.
![]() |
Cover the steering pad (Using a cardboard box).
Cover the steering pad with the cardboard box.
Place weights of at least 190 N (19 kg, 43 lb) on the cardboard box in 4 places.
| Area | Measurement |
| X | 460 mm (18.11 in.) |
| Y | 650 mm (25.59 in.) |
Cover the steering pad (Using tires).
![]() |
Place at least 3 tires without disc wheels on the tire with disc wheel to which the steering pad is tied.
Place the tire with a disc wheel on top of them.
| Area | Measurement |
| Width | 185 mm (7.28 in.) |
| Inner diameter | 360 mm (14.17 in.) |
![]() |
Tie the tires together with 2 wire harnesses.
Deploy the airbag.
![]() |
Connect the red clip of SST to the positive (+) battery terminal and the black clip of the SST to the negative (-) terminal.
Check that no one is within a 10 m (33 ft) radius of the disc wheel to which the steering pad is tied.
Press the SST activation switch and deploy the airbag.
![]() |
Dispose of the steering pad.
Remove the steering pad from the disc wheel.
Place the steering pad in a plastic bag, tie it tightly and dispose of it in the same way as other general parts.