Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › BLOWER UNIT

BLOWER UNIT > INSTALLATION

for Preparation Click here



1. INSTALL BLOWER UNIT ASSEMBLY


I102448
  1. Install the 2 screws and blower unit as shown in the illustration.



2. INSTALL INSTRUMENT PANEL REINFORCEMENT
  1. Provisionally install the air conditioning unit assembly.

  1. Insert the bracket hook into the holes of the reinforcement bracket, and provisionally install the reinforcement.

  1. Install the instrument panel reinforcement with the 7 bolts.



  1. Install the 2 caps.


    I102444

  1. Install the 5 bolts.

    NOTICE:
    Tighten the bolts in the sequence order shown in the illustration to install the air conditioner unit assembly.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for bolt



  1. Install the 2 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf } for nut



    I102442E01



  1. Engage the clamps.


    I102441

  1. Connect the connectors.



  1. Connect the wire harness with the 3 bolts and 5 nuts.


    I102440

    Torque:
    7.3 N*m{ 74 kgf*cm , 65 in.*lbf } for nut



3. INSTALL COOLER UNIT DRAIN HOSE


    I102468
  1. Install the cooler unit drain hose.



4. INSTALL MAIN BODY ECU (DRIVER SIDE J/B)


    I102439
  1. Install the main body ECU with the 2 nuts.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



5. INSTALL INSTRUMENT PANEL SIDE BRACKET


    I102438
  1. Install the instrument panel side bracket with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



6. INSTALL STEERING COLUMN ASSEMBLY


C133810
  1. Install the steering column assembly with the 4 nuts.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  1. Connect each of the connectors to the steering column assembly.

  1. Connect the wire harness clamps to the steering column assembly.

    CAUTION:
    Use a piece of cloth to wipe any dirt off the installation plane and column body side.

    NOTICE:
    Be careful not to scratch or soil the installation plane of the steering column.



7. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY


I102502E01
  1. Align the matchmarks on the steering column assembly and the steering intermediate shaft assembly.

  1. Install the steering intermediate shaft assembly and thrust stopper onto the steering column assembly with the bolt.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



8. INSTALL STEERING COLUMN HOLE COVER


F051329E01
  1. Install the steering column hole cover with the 4 clips.

    NOTICE:
    Be careful not to damage the dust seal of the steering column hole cover.



9. INSTALL ECM
  1. Install the ECM with the 3 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the 6 connectors.



10. INSTALL NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET


I102436
  1. for LH side:

    1. Install the instrument panel brace mounting bracket with the bolt and nut.



    I102437
  1. for RH side:

    1. Install the instrument panel brace mounting bracket with the bolt and nut.



11. INSTALL NO. 1 AIR DUCT


I102434
  1. Engage the 3 claws and install the air duct.



12. INSTALL NO. 2 AIR DUCT


I102432
  1. Engage the 6 claws and 3 clamps and install the air duct.



13. INSTALL REAR NO. 1 AIR DUCT


I102433
  1. Engage the 6 claws and 3 clamps and install the air duct.



14. INSTALL REAR NO. 2 AIR DUCT


I102432
  1. Engage the 6 claws and 3 clamps and install the air duct.



15. INSTALL NO. 1 HEATER TO REGISTER DUCT


I102430
  1. Install the heater to register duct with the screw.



16. INSTALL NO. 2 HEATER TO REGISTER DUCT


I102431
  1. Install the heater to register duct with the screw.



17. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY



B133866E01

  1. Install the lower instrument panel with the 2 <C> bolts, 2 <E> bolts, 7 <F> bolts and nut <G>.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf } for bolt <C>

  1. Engage the clamps and connect the connectors.



18. CONNECT PASSENGER AIRBAG CONNECTOR


B133891
  1. Connect the passenger airbag connector.



19. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


    B133889
  1. Engage the 3 claws and install the instrument panel finish panel end.



20. INSTALL ASSIST GRIP RETAINER RH


    B133881
  1. Install the assist grip retainer with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



21. INSTALL ASSIST GRIP RETAINER LH

HINT:
Use the same procedure as for the RH side.



22. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY


    E219214
  1. Engage the clamp.

  1. Insert the 2 hooks into the 2 cutouts of the front speaker bracket and install the front No. 2 speaker with the 2 bolts.

    Torque:
    8.1 N*m{ 85 kgf*cm , 72 in.*lbf }



23. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B133865
  1. Engage the 4 clips and claw and install the instrument panel speaker panel.



24. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

HINT:
Use the same procedure as for the RH side.



25. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    B287549
  1. Engage the 4 clips and 2 claws and install the instrument panel register.

  1. Install the bolt <F> and clip.



    B287552
  1. Engage the 2 claws and install the instrument panel hole cover.



26. INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH


    B133857
  1. Install the connectors to the instrument panel lower finish panel.

  1. Engage the claw and 2 clips and install the instrument panel lower finish panel.

  1. Install screw <A>.



27. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    B133856
  1. Install the glove compartment door assembly with the 3 hinges while holding it horizontal.



    B133854E01
  1. Slightly flex the upper part of the glove compartment door assembly, and install the glove compartment door assembly.

  1. Install the glove compartment door stoppers onto the glove compartment door.



28. INSTALL COMBINATION METER ASSEMBLY


    B133863
  1. Connect the 2 connectors and the clamp.



    B133862
  1. Install the combination meter assembly with the 4 screws.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



29. INSTALL INSTRUMENT CLUSTER FINISH PANEL


B133861
  1. Connect the connectors.

  1. Engage the 3 clips and 4 claws and install the instrument cluster lower finish panel.



30. INSTALL LOWER INSTRUMENT PANEL LH


    B133864
  1. Install the lower instrument panel with the 4 <F> bolts.



31. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B133860
  1. Engage the 5 clips and claw and install the lower instrument panel finish panel.

  1. Connect the connector.

  1. Install the 2 <F> bolts.



32. INSTALL INSTRUMENT PANEL FINISH PLATE


E149563E01
  1. Install the instrument panel finish plate.



33. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B133859
  1. Engage the 3 claws and install the hood lock control lever.



34. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    B133853
  1. Engage the 4 clips and 2 claws and install the instrument panel register.



35. INSTALL INSTRUMENT LOWER COVER SUB-ASSEMBLY


    B133852
  1. Engage the 3 clips and 2 claws and install the instrument lower cover.

  1. Install the 2 <F> bolts and 2 clips.



36. INSTALL CONSOLE UPPER PANEL NO. 1 GARNISH


B133902E01
  1. Slide the console upper panel garnish toward the front of the vehicle and engage claw B.

  1. Engage the claw and clip and install the console upper panel garnish.



37. INSTALL FRONT CONSOLE BOX


    B133851
  1. Engage the 5 claws and install the front console box.

  1. Install the 4 <D> screws.



38. INSTALL BOX BOTTOM MAT


    B133899
  1. Install the box bottom mat.



39. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY


    B133897
  1. Engage the 3 claws and 5 clips and install the console upper rear panel.



40. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)


    B133894
  1. Install the shift lever knob.



41. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for 4WD)


    B133896
  1. Install the shift lever knob.



42. INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY


B133901E01
  1. Slide the parking brake hole cover toward the rear of the vehicle and engage the 2 C claws.

  1. Engage the 4 claws and install the parking brake hole cover.



43. INSTALL RADIO RECEIVER ASSEMBLY


    E221532
  1. Connect the connectors.

  1. Align the 2 bosses of the radio bracket with the hole in the instrument panel and install the radio receiver with the 4 bolts.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }



44. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


B133888
  1. Connect the 3 connectors.

  1. Engage the 4 clips and install the integration control panel assembly.

  1. Install the 2 <H> screws.



45. INSTALL INSTRUMENT PANEL GARNISH LH


    B133886
  1. Engage the 3 clips and install the instrument panel garnish.

  1. Install 2 <H> screws.



46. INSTALL INSTRUMENT PANEL GARNISH RH


    B133887
  1. Engage the 3 clips and install the instrument panel garnish.

  1. Install screw <H>.



47. INSTALL FRONT PILLAR GARNISH RH
  1. Engage the guide and the 2 clips and install the front pillar garnish.



48. INSTALL FRONT PILLAR GARNISH LH

HINT:
Use the same procedure as for the RH side.



49. INSTALL ASSIST GRIP ASSEMBLY

HINT:
Use the same procedure to install all the assist grips.

  1. Install the assist grip with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



50. INSTALL ASSIST GRIP PLUG


B175649E03

HINT:
Use the same procedure to install all the assist grip plugs.

Text in Illustration 
*a
for RH Side
*b
for LH Side
  1. Engage the 2 claws and install the assist grip plug.



51. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.



52. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip.



53. INSTALL COWL SIDE TRIM BOARD RH
  1. Engage the 2 claws and install the cowl side trim board.

  1. Install the clip.



54. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



55. INSTALL FOOTREST CLIP


B130588

HINT:
Use the same procedure for both sides.

  1. Engage the 2 claws and install the footrest clip.



56. INSTALL FRONT FLOOR FOOTREST


    B130589
  1. Engage the 2 studs and install the front floor footrest.



57. INSTALL FRONT DOOR SCUFF PLATE RH


    B130597
  1. Engage the 14 claws and install the door scuff plate.



58. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



59. INSTALL COMBINATION SWITCH ASSEMBLY


    C133809
  1. Install the 3 screws.

  1. Connect all connectors to the combination switch assembly.



60. INSTALL UPPER STEERING COLUMN COVER


    C231841
  1. Engage the claw and install the upper steering column cover.



61. INSTALL LOWER STEERING COLUMN COVER


    C133807
  1. Engage the 2 claws.

  1. Install the lower steering column cover with the 3 screws.



62. INSTALL STEERING WHEEL ASSEMBLY
  1. Align the matchmarks on the steering wheel assembly and steering main shaft assembly.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



63. INSTALL STEERING PAD


    C128255E01
  1. Support the steering pad with one hand as shown in the illustration.

  1. Connect the 2 connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector.

  1. Confirm that the circumferencial groove of the "Torx" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

  1. Using "Torx" socket wrench (T30), tighten the 2 "Torx" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }

    NOTICE:
    Tighten the 2 bolts while holding the steering pad to prevent it from moving upward.



64. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    C128196
  1. Install steering wheel cover lower No.2.



65. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    C128196
  1. Install steering wheel cover lower No.2.



66. CONNECT HEATER WATER OUTLET HOSE A (FROM HEATER UNIT)


I102429E01
  1. Install the heater water outlet hose onto the heater unit.

    NOTICE:
    Perform the installation with the hose clip and mark at the correct angle as shown in the illustration.



67. CONNECT HEATER WATER HOSE INLET


I102427E01
  1. Install the heater water inlet hose onto the heater unit.

    NOTICE:
    Perform the installation with the hose clip and mark at the correct angle as shown in the illustration.



68. INSTALL COOLER REFRIGERANT LIQUID PIPE A


I006878E06
  1. Remove the vinyl tape from liquid tube A and the connecting portion of the unit.

  1. Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the connecting part of the liquid pipe.

    Compressor oil:
    ND-OIL8 or the equivalent

  1. Install the O-ring onto the liquid pipe.

  1. Install the liquid and piping clamp.

    HINT:
    After connection, check the claw fitting of the piping clamp.



69. INSTALL COOLER REFRIGERANT SUCTION PIPE A

HINT:
Connection procedure of the suction pipe is the same as for the liquid pipe.



70. INSTALL COWL TOP VENTILATOR LOUVER LH


    E127865
  1. Install the cowl top ventilator louver LH with the 5 clips and engage the 7 claws.



71. INSTALL COWL TOP VENTILATOR LOUVER RH


    E127864
  1. Install the cowl top ventilator louver RH with the 3 clips and the claw.

  1. Install the hood to cowl top seal with the clip.



72. INSTALL COWL TOP VENTILATOR LOUVER ASSEMBLY


    E127863
  1. Install the cowl top ventilator louver sub-assembly with the 7 clips.



73. INSTALL FRONT FENDER SIDE PANEL UPPER LH
  1. Install the 4 new clips on the front fender side panel upper LH.



    B210065
  1. Engage the 4 clips and install the front fender side panel upper LH.



74. INSTALL FRONT FENDER SIDE PANEL UPPER RH
  1. Install the 4 new clips on the front fender side panel upper RH.



    B210064
  1. Engage the 4 clips and install the front fender side panel upper RH.



75. INSTALL ANTENNA ORNAMENT


    E127861E02
  1. Press in the antenna ornament in the direction shown in the illustration.



76. INSTALL ROOF ANTENNA POLE SUB-ASSEMBLY


    E148353E01
  1. Install the radio antenna pole sub-assembly by hand until fully seated.
    Text in Illustration 
    *a
    1/8 turn (20 to 45 degrees)

  1. Using a 8 mm (5/16 inch) wrench, fully tighten the radio antenna pole about 1/8 turn (20 to 45 degrees) by turning it clockwise.

    NOTICE:
    1. Do not over tighten. Tighten with finger, not hand.
    2. Do not use pliers to tighten the radio antenna pole as it can leave marks on the radio antenna pole surface.
    3. The antenna pole cannot be hand tightened to the proper specification.

    Torque:
    3.3 N*m{ 34 kgf*cm , 29 in.*lbf }



77. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E127876E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



78. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (CENTER SIDE)


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E127875E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



79. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E127874E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



80. INSTALL WINDSHIELD WIPER ARM COVER


    E127877E01
  1. Engage the claw and install the 3 front wiper arm cover.



81. ADD ENGINE COOLANT
  1. Tighten the cylinder block drain cock plug.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.

  1. Remove the vinyl hose from the radiator drain cock of the radiator assembly.

  1. Add engine coolant.

    Standard Capacity:
    Item
    Specified Condition
    for Automatic Transmission
    9.8 liters (10.4 US qts, 8.6 Imp. qts)
    for Manual Transmission
    9.4 liters (9.9 US qts, 8.3 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Press the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the engine coolant level. If the engine coolant level is low, add engine coolant.



    A220212E03
  1. Slowly pour engine coolant into the radiator reservoir until it reaches the Full line.
    Text in Illustration 
    *a
    Full Line

  1. Install the radiator reserve tank cap sub-assembly.

  1. Install the radiator cap sub-assembly.*1

  1. Start the engine and stop it immediately.*2

  1. Allow approximately 10 seconds to pass, and then remove the radiator cap sub-assembly and check the engine coolant level. If the engine coolant level has decreased, add engine coolant.*3

  1. Repeat steps *1, *2 and *3 until the engine coolant level does not decrease.

    HINT:
    Be sure to perform this step while the engine is cold, as air in the No. 1 radiator hose will flow into the radiator assembly if the engine is warmed up and the thermostat opens.

  1. Install the radiator cap sub-assembly.*4

  1. Set the air conditioning as follows.*5
    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the engine coolant.*6

    CAUTION:
    1. Wear protective gloves. Hot areas on the parts may injure your hands.
    2. Be careful of the fan.
    3. Be careful as the engine, radiator assembly and radiator hoses are hot and can cause burns.

    NOTICE:
    1. Immediately after starting the engine, if the radiator reservoir becomes empty, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant until the engine coolant is filled to the Full line.
    2. Do not start the engine when there is no engine coolant in the radiator reservoir.
    3. Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
    4. If there is not enough engine coolant, the engine may burn out or overheat.

    HINT:
    1. Press the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air while warming up the engine.
    2. The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand and checking when the engine coolant starts to flow inside the hose.

  1. Stop the engine, wait until the engine coolant cools down to ambient temperature, and then remove the radiator cap sub-assembly and check the engine coolant level.*7

    CAUTION:
    Do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. If the engine coolant level has decreased, add engine coolant and warm up the engine until the thermostat opens.*8



    A220212E03
  1. If the engine coolant level has not decreased, check that the engine coolant level in the radiator reservoir is at the Full line.
    If the engine coolant level is below the Full line, repeat steps *4 through *8.
    If the engine coolant level is above the Full line, drain engine coolant until the engine coolant level reaches the Full line.
    Text in Illustration 
    *a
    Full Line

  1. Install the service hole cover to the engine under cover.



82. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



83. CHECK SRS WARNING LIGHT
Click here


84. CHARGE REFRIGERANT



I100449E06

NOTICE:
Charge refrigerant in accordance with equipment manual.

  1. Perform vacuum purging using a vacuum pump.

  1. Charge refrigerant HFC-134a (R134a).

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    Standard:
    570 to 630 g (20.11 to 22.22 oz.)

    NOTICE:
    Do not start the engine before charging it with refrigerant as the cooler compressor doesn't work properly without sufficient refrigerant. This could cause the compressor to overheat.

    HINT:

    1. The relationship between the refrigerant charge amount and the pressure is as follows.


      I101544E01

    2. High Charge Range:
      If the refrigerant is overcharged, the pressure rises on the high-pressure side. High-pressure cut off frequently occurs. This causes insufficient cooling performance and also insufficient compressor lubrication.
    3. Low Charge Range:
      Shortage of refrigerant causes insufficient cooling performance and low circulation of refrigerant oil, which shortens the compressor life. Operation with insufficient coolant raises refrigerant temperature and causes heat deterioration of the rubber seals and hoses. Cracking and thus refrigerant leakage may occur.


    1. Install the caps onto the service valves on the refrigerant line.



85. WARM UP ENGINE

NOTICE:
Warm up the engine at less than 2,000 rpm for 2 minute or more after charging it with refrigerant.



86. CHECK FOR ENGINE COOLANT LEAK

CAUTION:
To avoid being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion may cause hot engine coolant and steam to blow out from the radiator.

  1. Fill the radiator with engine coolant, and then attach a radiator cap tester.

  1. Warm up the engine.



    A220211E01
  1. Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
    Text in Illustration 
    *1
    Radiator Cap Tester



87. CHECK FOR REFRIGERANT LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation as follows:

    1. Stop the engine.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system.
      When the compressor is off: approximately 392 to 588 kPa (4 to 6 kgf*cm2, 57 to 85 psi)

    HINT:
    It is impossible for the above pressure to be maintained if there is leakage.



    I042222E14
  1. Using the halogen leak detector, check the refrigerant line, especially at the connection points, for leakage.



    I100587E02
  1. Bring the halogen leak detector close to the drain hose before performing the test.

    HINT:
    1. After the blower motor has stopped, leave the cooling unit for at least 15 minutes.
    2. Place the halogen leak detector sensor under the drain hose.
    3. When bringing the halogen leak detector close to the drain hose, make sure that the halogen leak detector does not react to the volatile gases.

    If such a reaction is unavoidable, the vehicle must be lifted up.

  1. If no gas leakage is detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.



88. POSITION FRONT WHEELS FACING STRAIGHT AHEAD