Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Fuel Injector Circuit

for Preparation Click here


DESCRIPTION

The fuel injector assemblies inject fuel based on the signals from the ECM.

WIRING DIAGRAM


A226863E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT FUEL INJECTOR ASSEMBLY (POWER SOURCE)


    A167963E34
  1. Disconnect the fuel injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B11-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B25-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B10-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B21-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B18-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)



NG
Go to step 6
OK


2.INSPECT FUEL INJECTOR ASSEMBLY (INJECTOR RESISTANCE)
A141550E22
  1. Disconnect the B11, B25, B10, B21, B9 and B18 fuel injector assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    11.6 to 12.4 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Fuel Injector Assembly)

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the B50 ECM connector.

  1. Disconnect the B11, B25, B10, B21, B9 and B18 fuel injector assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B11-2 - B50-6 (#10)
    Always
    Below 1 Ω
    B25-2 - B50-1 (#20)
    Always
    Below 1 Ω
    B10-2 - B50-7 (#30)
    Always
    Below 1 Ω
    B21-2 - B50-2 (#40)
    Always
    Below 1 Ω
    B9-2 - B50-8 (#50)
    Always
    Below 1 Ω
    B18-2 - B50-3 (#60)
    Always
    Below 1 Ω
    B11-2 or B50-6 (#10) - Body ground
    Always
    10 kΩ or higher
    B25-2 or B50-1 (#20) - Body ground
    Always
    10 kΩ or higher
    B10-2 or B50-7 (#30) - Body ground
    Always
    10 kΩ or higher
    B21-2 or B50-2 (#40) - Body ground
    Always
    10 kΩ or higher
    B9-2 or B50-8 (#50) - Body ground
    Always
    10 kΩ or higher
    B18-2 or B50-3 (#60) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. Disconnect the B50 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    B50-14 (E01) - Body ground
    Always
    Below 1 Ω
    B50-15 (E02) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
  1. Check the fuel injector assembly and volume (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - IGNITION SWITCH)
  1. Disconnect the B11, B25, B10, B21, B9 and B18 fuel injector assembly connectors.

  1. Disconnect the A1 ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B11-1 - A1-6 (IG2)
    Always
    Below 1 Ω
    B25-1 - A1-6 (IG2)
    Always
    Below 1 Ω
    B10-1 - A1-6 (IG2)
    Always
    Below 1 Ω
    B21-1 - A1-6 (IG2)
    Always
    Below 1 Ω
    B9-1 - A1-6 (IG2)
    Always
    Below 1 Ω
    B18-1 - A1-6 (IG2)
    Always
    Below 1 Ω
    B11-1 or A1-6 (IG2) - Body ground
    Always
    10 kΩ or higher
    B25-1 or A1-6 (IG2) - Body ground
    Always
    10 kΩ or higher
    B10-1 or A1-6 (IG2) - Body ground
    Always
    10 kΩ or higher
    B21-1 or A1-6 (IG2) - Body ground
    Always
    10 kΩ or higher
    B9-1 or A1-6 (IG2) - Body ground
    Always
    10 kΩ or higher
    B18-1 or A1-6 (IG2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)