Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio receiver.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.
If there is a short in the circuit, the resulting condition is the same as if the switch were continuously depressed. Therefore, the audio system cannot be operated using the steering pad switch, and the audio system itself cannot function.

WIRING DIAGRAM


E219857E01


INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution for the SRS (Click here).

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPIRAL CABLE)
  1. Disconnect the E43 radio receiver connector.

  1. Disconnect the E17 spiral cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E43-8 (SW2) - E17-11 (AU2)
    Always
    Below 1 Ω
    E43-6 (SWG) - E17-10 (EAU)
    Always
    Below 1 Ω
    E43-7 (SW1) - E17-12 (AU1)
    Always
    Below 1 Ω
    E43-8 (SW2) - Body ground
    Always
    10 kΩ or higher
    E43-6 (SWG) - Body ground
    Always
    10 kΩ or higher
    E43-7 (SW1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
E219813E01
  1. Disconnect the spiral cable cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-10 (EAU) - B-10 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    A-11 (AU2) - B-11 (AU2)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    A-12 (AU1) - B-12 (AU1)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    Text in Illustration 
    *a
    Vehicle Side
    *b
    Steering Pad Switch Side

    CAUTION:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS (Click here).



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


3.INSPECT STEERING PAD SWITCH ASSEMBLY


  1. Disconnect the steering pad switch connector.


    E219811E01


    Text in Illustration 
    *a
    Volume+
    *b
    Volume-
    *c
    Seek-
    *d
    MODE
    *e
    Seek+
    *f
    Off Hook
    *g
    On Hook
    *h
    Voice

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    12 (AU1) - 10 (EAU)
    No switch is pushed
    95 to 105 kΩ
    Seek+ switch pushed
    Below 2.5 Ω
    Seek- switch pushed
    312 to 345 Ω
    Volume+ switch pushed
    950 to 1050 Ω
    Volume- switch pushed
    2954 to 3265 Ω
    11 (AU2) - 10 (EAU)
    No switch is pushed
    95 to 105 kΩ
    MODE switch pushed
    Below 2.5 Ω
    On hook switch pushed
    312 to 345 Ω
    Off hook switch pushed
    950 to 1050 Ω
    Voice switch pushed
    2954 to 3265 Ω



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)