DTC P0112 Intake Air Temperature Circuit Low Input |
DTC P0113 Intake Air Temperature Circuit High Input |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0112 | Short in Intake Air Temperature (IAT) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0113 | Open in Intake Air Temperature (IAT) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| Temperature Displayed | Malfunction |
| -40°C (-40°F) | Open circuit |
| Higher than 128°C (262°F) | Short circuit |
| Related DTCs | P0112: Intake air temperature sensor range check (low voltage) P0113: Intake air temperature sensor range check (high voltage) |
| Required Sensors/Components (Main) | Intake air temperature sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Intake air temperature sensor voltage | Less than 0.18 V [Higher than 128°C (262°F)] |
| Intake air temperature sensor voltage | More than 4.91 V [Less than -55°C (-67°F)] |
| Intake air temperature sensor voltage | 0.18 V to 4.91 V [-55 to 128°C (-67 to 262°F)] |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING TECHSTREAM (INTAKE AIR TEMPERATURE) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the Techstream.
| Result | Proceed to |
| -40°C (-40°F) | A |
| Higher than 128°C (262°F) | B |
| Same as actual IAT | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS) |
![]() |
Disconnect the Mass Air Flow (MAF) meter connector.
Connect terminals THA and E2 of the MAF meter wire harness side connector.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the Techstream.
| *1 | MAF Meter |
| *2 | ECM |
| *a | Front view of wire harness connector (to Mass Air Flow Meter) |
|
| ||||
| OK | ||
| ||
| 3.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN ECM) |
![]() |
Disconnect the B51 MAF meter connector.
Connect terminals THA and ETHA of the ECM connector.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the Techstream.
| *1 | MAF Meter |
| *2 | ECM |
| *a | Component with harness connected (ECM) |
|
| ||||
| OK | ||
| ||
| 4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS) |
![]() |
Disconnect the B51 MAF meter connector.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the Techstream.
| *1 | MAF Meter |
| *2 | ECM |
|
| ||||
| OK | ||
| ||
| 5.READ VALUE USING TECHSTREAM (CHECK FOR SHORT ECM) |
![]() |
Disconnect the B51 MAF meter connector.
Disconnect the ECM connector.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the Techstream.
| *1 | MAF Meter |
| *2 | ECM |
| *a | Rear view of wire harness connector (to ECM) |
|
| ||||
| OK | ||
| ||