Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0115    Engine Coolant Temperature Circuit

DTC    P0117    Engine Coolant Temperature Circuit Low Input

DTC    P0118    Engine Coolant Temperature Circuit High Input

for Preparation Click here


DESCRIPTION

A thermistor is built into the Engine Coolant Temperature (ECT) sensor, of which the resistance value varies according to the ECT.
The structure of the sensor and its connection to the ECM are the same as those of the Intake Air Temperature (IAT) sensor.

HINT:
When any of DTCs P0115, P0117 and P0118 are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECT is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No.
DTC Detection Condition
Trouble Area
P0115
Open or short in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Open or short in ECT sensor circuit
  2. ECT sensor
  3. ECM
P0117
Short in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Short in ECT sensor circuit
  2. ECT sensor
  3. ECM
P0118
Open in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Open in ECT sensor circuit
  2. ECT sensor
  3. ECM

HINT:
When any of these DTCs are output, check the ECT by entering the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
Higher than 135°C (275°F)
Short circuit


MONITOR DESCRIPTION

The Engine Coolant Temperature (ECT) sensor is used to monitor the ECT. The ECT sensor has a thermistor with a resistance that varies according to the temperature of the engine coolant. When the coolant temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance drops.
These variations in resistance are reflected in the voltage output from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the ECT. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a fault in the ECT sensor and stores a DTC.
Example:
If the sensor voltage output is more than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the ECT sensor circuit, and stores DTC P0118. Conversely, if the voltage output is less than 0.14 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and stores DTC P0117.
If the malfunction is not repaired successfully, a DTC is stored 0.5 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0115: Engine coolant temperature sensor range check (Fluctuating)
P0117: Engine coolant temperature sensor range check (low voltage)
P0118: Engine coolant temperature sensor range check (high voltage)
Required Sensors/Components (Main)
Engine coolant temperature sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None

TYPICAL MALFUNCTION THRESHOLDS


P0115 
Engine coolant temperature sensor voltage
[Engine coolant temperature]
Less than 0.14 V, or more than 4.91 V [Higher than 135°C (275°F), or less than -60°C (-76°F)]

P0117 
Engine coolant temperature sensor voltage
[Engine coolant temperature]
Less than 0.14 V [Higher than 135°C (275°F)]

P0118 
Engine coolant temperature sensor voltage
[Engine coolant temperature]
More than 4.91 V [Less than -60°C (-76°F)]

COMPONENT OPERATING RANGE


Engine coolant temperature sensor voltage
[Engine coolant temperature]
0.14 V to 4.91 V [-60 to 135°C (-76 to 275°F)]

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Wait 0.5 seconds or more.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  8. Read DTCs.

    HINT:
    1. If a DTC is output, the system is malfunctioning.
    2. If a DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0115, P0117 or P0118.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the judgment result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A115931E09


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.
  2. If DTC P0117 is stored, check that the engine does not overheat (the DTC P0117 may be stored due to engine overheating).

1.READ VALUE USING TECHSTREAM (ENGINE COOLANT TEMPERATURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the Techstream.

    Standard value:
    Between 75°C and 100°C (167°F and 212°F) with warm engine.

    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    Higher than 135°C (275°F)
    B
    Between 75°C and 100°C (167°F and 212°F)
    C

    HINT:
    1. If there is an open circuit, the Techstream indicates -40°C (-40°F).
    2. If there is a short circuit, the Techstream indicates higher than 135°C (275°F).



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)
A218185E03
  1. Disconnect the Engine Coolant Temperature (ECT) sensor connector.

  1. Connect terminals 1 and 2 of the ECT sensor connector on the wire harness side.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the Techstream.

    Standard value:
    Higher than 135°C (275°F)

    Text in Illustration 
    *1
    ECT Sensor
    *2
    ECM
    *a
    Front view of wire harness connector
    (to ECT Sensor)

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
Go to step 3
OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)  

3.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN ECM)
A226224E04
  1. Disconnect the B52 ECT sensor connector.

  1. Connect terminals THW and ETHW of the ECM connector.

    HINT:
    Before checking, do visual and contact pressure checks on the ECM connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the Techstream.

    Standard value:
    Higher than 135°C (275°F)

    Text in Illustration 
    *1
    ECT Sensor
    *2
    ECM
    *a
    Component with harness connected
    (ECM)



NG
CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) 

4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)
A218184E04
  1. Disconnect the B52 ECT sensor connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the Techstream.

    Standard value:
    -40°C (-40°F)

    Text in Illustration 
    *1
    ECT Sensor
    *2
    ECM

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
Go to step 5
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)  

5.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN ECM)


    A226226E03
  1. Disconnect the B52 ECT sensor connector.

  1. Disconnect the ECM connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the Techstream.

    Standard value:
    -40°C (-40°F)

    Text in Illustration 
    *1
    ECT Sensor
    *2
    ECM
    *a
    Rear view of wire harness connector
    (to ECM)



NG
REPLACE ECM (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)