Home › ENGINE › 1GR-FE COOLING › WATER PUMP

WATER PUMP > INSTALLATION

for Preparation Click here



1. INSTALL ENGINE WATER PUMP ASSEMBLY


    A223007E01
  1. Install a new gasket and the engine water pump with the 17 bolts.

    Torque:
    for bolt A:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }
    for bolt B:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }
    for bolt C:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



2. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


A226495E01
  1. Temporarily install the V-ribbed belt tensioner assembly to the cylinder block sub-assembly and timing chain cover sub-assembly with the 5 bolts.
    Text in Illustration 
    V100135
    Bolt A
    V100136
    Bolt B

    Bolt Length:
    Item
    Length
    A
    70 mm (2.76 in.)
    B
    33 mm (1.30 in.)

  1. Tighten bolts 1 and 2 in numerical order.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Tighten the other bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



3. INSTALL COOLER COMPRESSOR ASSEMBLY


4. INSTALL GENERATOR ASSEMBLY
  1. Install the generator assembly (Click here).



5. INSTALL VANE PUMP ASSEMBLY
  1. Install the vane pump with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Connect the 2 clamps and vane pump connector.



6. INSTALL FRONT FENDER APRON SEAL RH
  1. Install the front fender apron seal RH to the front fender apron sub-assembly RH with the 4 clips.



7. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY
  1. for Cover Separate Type:
    Install the 2 idler pulley cover plates, 2 No. 2 idler pulleys and 2 No. 2 idler pulley cover plates with the 2 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. for Cover Integrated Type:
    Install the 2 No. 2 idler pulleys with the 2 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }



8. INSTALL WATER INLET HOUSING


A223008
  1. Install a new O-ring to the water outlet pipe.

  1. Install a new O-ring to the water pump.

  1. Apply soapy water to the O-ring of the water outlet pipe.

  1. Install the water inlet with the 5 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 5 water by-pass hoses.

  1. Connect the throttle body connector.



9. CONNECT NO. 1 RADIATOR HOSE


    A287964E01
  1. Connect the No. 1 radiator hose to the water inlet housing with the hose clip.
    Text in Illustration 
    *1
    No. 1 Radiator Hose
    *2
    No. 1 Air Injection System Hose
    *3
    Hose Clamp
    *a
    View A
    *b
    View B
    *c
    Upper Side
    *d
    Front Side
    *e
    Hose Paint Mark

  1. Install a new hose clamp to the No. 1 radiator hose and the No. 1 air injection system hose at the location shown in the illustration.

    HINT:
    Perform the installation with the hose clamp at the correct angle.



10. CONNECT NO. 2 RADIATOR HOSE


    A287971E01
  1. Connect the No. 2 radiator hose to the water inlet with thermostat with the hose clip.
    Text in Illustration 
    *a
    View A
    *b
    Upper Side
    *c
    Front Side
    *d
    Hose Paint Mark

    HINT:
    Perform the installation with the hose clip at the correct angle.



11. INSTALL FAN SHROUD
  1. Install the fan pulley to the engine water pump assembly.

  1. Place the fan shroud together with the fan and fluid coupling assembly between the radiator assembly and engine.

    NOTICE:
    Be careful not to damage the radiator core.



    A226673E01
  1. Align the paint marks of the same color (pink to pink and black to black) on the stud bolts of the engine water pump assembly and the outer flange of the fan and fluid coupling assembly, and assemble the parts.
    Text in Illustration 
    *a
    Paint Mark

  1. Temporarily install the fan and fluid coupling assembly to the engine water pump assembly with the 4 nuts. Tighten the nuts as much as possible by hand.



    A287972E01
  1. Engage the 2 guides of the fan shroud to the radiator assembly as shown in the illustration.

  1. Install the fan shroud to the radiator assembly with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the radiator reserve tank assembly to the radiator assembly with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the 2 oil cooler hoses to the hose clamp and engage the clamp.
    Text in Illustration 
    *1
    Oil Cooler Hose



    A225650E01
  1. Set the fan and generator V belt onto every part.
    Text in Illustration 
    *1
    Vane Pump Assembly
    *2
    Engine Water Pump Assembly
    *3
    No. 2 Idler Pulley Sub-Assembly
    *4
    Generator Assembly
    *5
    Cooler Compressor Assembly
    *6
    No. 1 Idler Pulley Sub-Assembly
    *7
    Crankshaft Pulley
    *8
    V-ribbed Belt Tensioner Assembly

  1. While turning the V-ribbed belt tensioner assembly counterclockwise, remove the pin.

    NOTICE:
    Make sure that the fan and generator V belt is properly set to each pulley.

  1. Check that the belt fits properly in the ribbed grooves.

    HINT:
    Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.

  1. Tighten the 4 nuts of the fan and fluid coupling assembly.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the radiator reserve tank hose to the radiator assembly.



12. INSTALL UPPER RADIATOR SUPPORT SEAL


    A226651
  1. Engage the 7 clips and install the upper radiator support seal to the fan shroud.



13. INSTALL V-BANK COVER
  1. Engage the 2 hooks and install the V-bank cover to the No. 1 V-bank cover bracket.

  1. Align the 2 V-bank cover grommets with the 2 pins and press down on the V-bank cover to engage the pins.



14. ADD ENGINE COOLANT
  1. Tighten the cylinder block drain cock plug.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.

  1. Remove the vinyl hose from the radiator drain cock of the radiator assembly.

  1. Add engine coolant.

    Standard Capacity:
    Item
    Specified Condition
    for Automatic Transmission
    9.8 liters (10.4 US qts, 8.6 Imp. qts)
    for Manual Transmission
    9.4 liters (9.9 US qts, 8.3 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Press the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the engine coolant level. If the engine coolant level is low, add engine coolant.



    A220212E03
  1. Slowly pour engine coolant into the radiator reservoir until it reaches the Full line.
    Text in Illustration 
    *a
    Full Line

  1. Install the radiator reserve tank cap sub-assembly.

  1. Install the radiator cap sub-assembly.*1

  1. Start the engine and stop it immediately.*2

  1. Allow approximately 10 seconds to pass, and then remove the radiator cap sub-assembly and check the engine coolant level. If the engine coolant level has decreased, add engine coolant.*3

  1. Repeat steps *1, *2 and *3 until the engine coolant level does not decrease.

    HINT:
    Be sure to perform this step while the engine is cold, as air in the No. 1 radiator hose will flow into the radiator assembly if the engine is warmed up and the thermostat opens.

  1. Install the radiator cap sub-assembly.*4

  1. Set the air conditioning as follows.*5
    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the engine coolant.*6

    CAUTION:
    1. Wear protective gloves. Hot areas on the parts may injure your hands.
    2. Be careful of the fan.
    3. Be careful as the engine, radiator assembly and radiator hoses are hot and can cause burns.

    NOTICE:
    1. Immediately after starting the engine, if the radiator reservoir becomes empty, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant until the engine coolant is filled to the Full line.
    2. Do not start the engine when there is no engine coolant in the radiator reservoir.
    3. Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
    4. If there is not enough engine coolant, the engine may burn out or overheat.

    HINT:
    1. Press the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air while warming up the engine.
    2. The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand and checking when the engine coolant starts to flow inside the hose.

  1. Stop the engine, wait until the engine coolant cools down to ambient temperature, and then remove the radiator cap sub-assembly and check the engine coolant level.*7

    CAUTION:
    Do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. If the engine coolant level has decreased, add engine coolant and warm up the engine until the thermostat opens.*8



    A220212E03
  1. If the engine coolant level has not decreased, check that the engine coolant level in the radiator reservoir is at the Full line.
    If the engine coolant level is below the Full line, repeat steps *4 through *8.
    If the engine coolant level is above the Full line, drain engine coolant until the engine coolant level reaches the Full line.
    Text in Illustration 
    *a
    Full Line

  1. Install the service hole cover to the engine under cover.



15. INSPECT FOR ENGINE COOLANT LEAK

CAUTION:
To avoid being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion may cause hot engine coolant and steam to blow out from the radiator.

  1. Fill the radiator with engine coolant, and then attach a radiator cap tester.

  1. Warm up the engine.



    A220211E01
  1. Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
    Text in Illustration 
    *1
    Radiator Cap Tester



16. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Hook the No. 1 engine under cover sub-assembly to the frame.

  1. Install the 4 bolts to the No. 1 engine under cover sub-assembly.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }