STEERING COLUMN ASSEMBLY > INSTALLATION |
| 1. INSTALL STEERING COLUMN ASSEMBLY |
![]() |
Install the steering column assembly with the 4 nuts.
Connect each of the connectors to the steering column assembly.
Connect the wire harness clamps to the steering column assembly.
| 2. INSTALL NO.2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
![]() |
Align the matchmarks on the power steering gear and No. 2 steering intermediate shaft.
Install the No. 2 steering intermediate shaft onto the steering gear box with bolt C.
| 3. INSTALL STEERING SLIDING YOKE |
Align the matchmarks on the steering column and steering sliding yoke.
Install the steering sliding yoke onto the steering column assembly and slide it upward.
Align the matchmarks on the No. 2 intermediate shaft sub-assembly and steering sliding yoke.
Install the sliding yoke onto the No. 2 intermediate shaft sub-assembly with bolts A and B.
| 4. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY |
Install the No. 1 engine under cover sub-assembly with the 4 bolts.
| 5. INSTALL FRONT WHEEL LH |
| 6. INSTALL STEERING COLUMN HOLE COVER |
![]() |
Install the steering column hole cover with the 4 clips.
| 7. INSTALL NO.1 AIR DUCT |
![]() |
Engage the 3 claws and install the air duct.
| 8. INSTALL LOWER INSTRUMENT PANEL LH |
![]() |
Install the lower instrument panel with the 4 <F> bolts.
| 9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH |
![]() |
Engage the 5 clips and claw and install the lower instrument panel finish panel.
Connect the connector.
Install the 2 <F> bolts.
| 10. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Install the front door opening trim weatherstrip.
| 11. INSTALL COWL SIDE TRIM BOARD LH |
| 12. INSTALL FRONT DOOR SCUFF PLATE LH |
| 13. INSTALL FRONT FLOOR FOOTREST |
![]() |
Engage the 2 studs and install the front floor footrest.
| 14. INSTALL NO.1 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Engage the 4 clips and 2 claws and install the instrument panel register.
| 15. INSTALL COMBINATION SWITCH ASSEMBLY |
![]() |
Install the 3 screws.
Connect all connectors to the combination switch assembly.
| 16. INSTALL UPPER STEERING COLUMN COVER |
![]() |
Engage the claw and install the upper steering column cover.
| 17. INSTALL LOWER STEERING COLUMN COVER |
![]() |
Engage the 2 claws.
Install the lower steering column cover with the 3 screws.
| 18. INSTALL STEERING WHEEL ASSEMBLY |
Align the matchmarks on the steering wheel assembly and steering main shaft assembly.
Install the steering wheel assembly set nut.
| 19. INSTALL STEERING PAD |
![]() |
Support the steering pad with one hand as shown in the illustration.
Connect the 2 connectors to the steering pad.
Connect the horn connector.
Confirm that the circumferencial groove of the "Torx" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
Using "Torx" socket wrench (T30), tighten the 2 "Torx" screws.
| 20. INSTALL LOWER NO.3 STEERING WHEEL COVER |
![]() |
Install steering wheel cover lower No.3.
| 21. INSTALL LOWER NO.2 STEERING WHEEL COVER |
![]() |
Install steering wheel cover lower No.2.
| 22. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 24. INSPECT SRS WARNING LIGHT |