Home › SUSPENSION & AXLE › SUSPENSION › FRONT SHOCK ABSORBER

FRONT SHOCK ABSORBER > INSTALLATION

for Preparation Click here



1. INSTALL FRONT SHOCK ABSORBER BUSH
  1. Using SST and a press, install a new front shock absorber bush.

    SST
    09710-22021   (09710-01071, 09710-01081)



2. INSTALL FRONT COIL SPRING


    C271294E01
  1. Install SST to the front coil spring, and secure SST in a vise.

    SST
    09727-00060  
    09727-30021   (09727-00010, 09727-00031)



    C263591
  1. Attach the arm of SST to the diameter of the front coil spring.

    CAUTION:
    1. Make sure that the front coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.
    2. Make sure that the claws of the hooks are securely attached.

  1. Using SST, compress the front coil spring.

    CAUTION:
    1. If the front coil spring bends during the compression, immediately stop the compression and reinstall SST.
    2. Do not compress the spring until the coil springs contact each other.
    3. Do not use an impact wrench. It will damage SST.



    C099165E01
  1. Install the front coil spring to the front shock absorber assembly.

    HINT:
    Fit the lower end of the front coil spring into the gap of the spring lower seat.



3. INSTALL FRONT SHOCK ABSORBER CUSHION RETAINER


4. INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY


    C214441E02
  1. Align the front suspension support sub-assembly and the front shock absorber bush as shown in the illustration.
    Text in Illustration 
    *1
    Front Shock Absorber Bush
    *2
    Front Suspension Support Sub-assembly
    *a
    LH Side
    *b
    RH Side
    V100135
    Front



5. INSTALL FRONT SHOCK ABSORBER NO. 1 CUSHION


6. INSTALL FRONT SHOCK ABSORBER CUSHION RETAINER


7. INSTALL FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT
  1. Tighten a new front support to front shock absorber nut.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Remove SST from the front coil spring.

    NOTICE:
    Do not use an impact wrench. It will damage the SST.



8. TEMPORARILY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING


    G021681E03
  1. Install the front coil spring to the vehicle body with the lower end of the coil spring facing the rear side of the vehicle.
    Text in Illustration 
    *a
    Lower End
    *b
    Outer Side
    *c
    Rear Side

  1. Install the 3 nuts onto the upper side of the front shock absorber with coil spring.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

  1. Temporarily tighten the bolt, nut and the washer on the lower side of the front shock absorber with coil spring.



9. INSTALL TIE ROD END SUB-ASSEMBLY


F043604
  1. Install the tie rod end onto the steering knuckle.

  1. Install the nut.

    Torque:
    91 N*m{ 928 kgf*cm , 67 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    If the holes in the cotter pin are not aligned, tighten the nut an additional 60°.



10. INSTALL FRONT STABILIZER BAR


G020162
  1. Install the stabilizer bar and 2 stabilizer brackets with the 4 bolts.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



11. INSTALL FRONT STABILIZER LINK ASSEMBLY LH
  1. Install the front stabilizer link assembly LH to the steering knuckle with the nut.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud.



12. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



13. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY

Torque:
29 N*m{ 296 kgf*cm , 21 ft.*lbf }



14. INSTALL FRONT WHEELS

Torque:
112 N*m{ 1137 kgf*cm , 82 ft.*lbf }



15. STABILIZE SUSPENSION
  1. Lower the vehicle.

  1. Bounce the vehicle up and down several times to stabilize the suspension.



16. FULLY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING


C234366
  1. Fully tighten the nut.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }



17. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)