Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1650/32    Occupant Classification System Malfunction

for Preparation Click here


DESCRIPTION

The occupant classification system circuit consists of the center airbag sensor assembly and occupant classification system.
If the center airbag sensor assembly receives signals from the occupant classification ECU, it determines whether the front passenger airbag, passenger side front seat cushion airbag and front seat belt pretensioner RH should be operated.
DTC B1650/32 is stored when a malfunction is detected in the occupant classification system circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1650/32
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the occupant classification system circuit.
  2. Occupant classification system malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. No. 1 seat wire
  3. Occupant classification system
  4. Center airbag sensor assembly

WIRING DIAGRAM


C268918E01


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.CHECK DTC (OCCUPANT CLASSIFICATION ECU)
  1. Check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC is not output.



NG
GO TO OCCUPANT CLASSIFICATION SYSTEM (Click here)
OK


2.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and occupant classification ECU. Also check that the connectors that link the floor wire and No. 1 seat wire are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and occupant classification ECU. Also disconnect the connectors that link the floor wire and No. 1 seat wire.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


3.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (OPEN)


    C268870E01
  1. Connect the connectors that link the floor wire and No. 1 seat wire.

  1. Using a service wire, connect terminals 16 (FSR+) and 24 (FSR-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q4-8 (FSR+) - Q4-4 (FSR-)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    Service Wire
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Occupant Classification ECU)



NG
Go to step 7
OK


4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO GROUND)
  1. Disconnect the service wire from connector B.



    C268873E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q4-8 (FSR+) - Body ground
    Always
    1 MΩ or higher
    Q4-4 (FSR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Occupant Classification ECU)



NG
Go to step 8
OK


5.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT)


    C268873E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q4-8 (FSR+) - Q4-4 (FSR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Occupant Classification ECU)



NG
Go to step 9
OK


6.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO B+)


    C268873E01
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Q4-8 (FSR+) - Body ground
    Ignition switch ON
    Below 1 V
    Q4-4 (FSR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Occupant Classification ECU)



NG
Go to step 10
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

7.CHECK FLOOR WIRE (OPEN)


    C268874E01
  1. Disconnect the No. 1 seat wire from the floor wire.

    HINT:
    The service wire has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    KQ1-1 (FSR+) - KQ1-4 (FSR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.
    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    No. 1 Seat Wire
    *4
    Floor Wire
    *5
    Service Wire
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to No. 1 Seat Wire)



NG
REPLACE FLOOR WIRE
OK

REPLACE NO. 1 SEAT WIRE 

8.CHECK FLOOR WIRE (SHORT TO GROUND)


    C268875E01
  1. Disconnect the No. 1 seat wire from the floor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    KQ1-1 (FSR+) - Body ground
    Always
    1 MΩ or higher
    KQ1-4 (FSR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    No. 1 Seat Wire
    *4
    Floor Wire
    *a
    Front view of wire harness connector
    (to No. 1 Seat Wire)



NG
REPLACE FLOOR WIRE
OK

REPLACE NO. 1 SEAT WIRE 

9.CHECK FLOOR WIRE (SHORT)


    C268875E01
  1. Disconnect the No. 1 seat wire from the floor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    KQ1-1 (FSR+) - KQ1-4 (FSR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    No. 1 Seat Wire
    *4
    Floor Wire
    *a
    Front view of wire harness connector
    (to No. 1 Seat Wire)



NG
REPLACE FLOOR WIRE
OK

REPLACE NO. 1 SEAT WIRE 

10.CHECK FLOOR WIRE (SHORT TO B+)


    C268875E01
  1. Disconnect the No. 1 seat wire from the floor wire.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    KQ1-1 (FSR+) - Body ground
    Ignition switch ON
    Below 1 V
    KQ1-4 (FSR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.
    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor Assembly
    *3
    No. 1 Seat Wire
    *4
    Floor Wire
    *a
    Front view of wire harness connector
    (to No. 1 Seat Wire)



NG
REPLACE FLOOR WIRE
OK

REPLACE NO. 1 SEAT WIRE