Home › DRIVE LINE ยท DRIVE SHAFT › FRONT DRIVE SHAFT ASSEMBLY

FRONT DRIVE SHAFT ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DRIVE SHAFT


F042771
  1. Coat the spline of the inboard joint shaft with ATF.

  1. Align the shaft splines and install the drive shaft with a brass bar and hammer.

    NOTICE:
    1. Set the snap ring with the opening side facing downward.
    2. Do not damage the oil seal.

    HINT:
    Whether the inboard joint shaft is in contact with the pinion shaft or not can be confirmed from the sound or feeling when driving it.



2. INSTALL FRONT LOWER BALL JOINT ATTACHMENT
  1. Install the front lower ball joint attachment with the 2 bolts.

    Torque:
    160 N*m{ 1631 kgf*cm , 118 ft.*lbf }



3. INSTALL TIE ROD END SUB-ASSEMBLY


F043604
  1. Install the tie rod end onto the steering knuckle.

  1. Install the nut.

    Torque:
    91 N*m{ 928 kgf*cm , 67 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    If the holes in the cotter pin are not aligned, tighten the nut an additional 60°.



4. INSTALL FRONT AXLE HUB NUT
  1. Install the hub nut.

    Torque:
    235 N*m{ 2396 kgf*cm , 174 ft.*lbf }

  1. Install the adjusting lock cap and a new cotter pin.



5. INSTALL FRONT AXLE HUB GREASE CAP


6. INSTALL FRONT SPEED SENSOR
  1. Install the skid control sensor wire onto the steering knuckle with the 2 bolts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Engage the clamp.

  1. Install the speed sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



7. INSTALL FRONT WHEEL

Torque:
112 N*m{ 1137 kgf*cm , 82 ft.*lbf }



8. INSPECT DIFFERENTIAL OIL


D025304E05
  1. Stop the vehicle on a level surface.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. After changing the oil seal, drive the vehicle and then check the oil level again.
    1. Too much or too little oil will lead to differential problems.

    HINT:
    If necessary, fill the differential carrier assembly with hypoid gear oil.

    Differential oil type and viscosity:
    Toyota Genuine Differential gear oil LT 75W-85 API GL-5 SAE 75W-85 or equivalent


    Differential Oil Capacity:

    Item
    Capacity
    Front Differential
    w/o A.D.D.
    1.35 to 1.45 Liters
    (1.43 to 1.53 US qts, 1.19 to 1.28 Imp qts.)
    w/ A.D.D.
    1.50 to 1.60 Liters
    (1.59 to 1.69 US qts, 1.32 to 1.41 Imp qts.)
    Rear Differential
    w/o Differential Lock
    2.45 to 2.55 Liters
    (2.59 to 2.69 US qts, 2.16 to 2.24 Imp qts.)
    w/ Differential Lock
    2.40 to 2.50 Liters
    (2.54 to 2.64 US qts, 2.11 to 2.20 Imp qts.)

  1. Check for oil leakage when the oil level is low.

  1. Install the differential filler plug with a new gasket.

    Torque:
    Front differential:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }
    Rear differential:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



10. CHECK VSC SENSOR SIGNAL
(Click here)


11. CHECK FOR DIFFERENTIAL OIL LEAKAGE


12. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)