Home › SUSPENSION & AXLE › AXLE › FRONT AXLE HUB

FRONT AXLE HUB > INSTALLATION

for Preparation Click here



1. INSTALL FRONT AXLE ASSEMBLY


2. INSTALL FRONT UPPER SUSPENSION ARM


G020157
  1. Install a nut and a new clip.

    Torque:
    110 N*m{ 1122 kgf*cm , 81 ft.*lbf }



3. INSTALL FRONT LOWER BALL JOINT ATTACHMENT
  1. Install the front lower ball joint attachment with the 2 bolts.

    Torque:
    160 N*m{ 1631 kgf*cm , 118 ft.*lbf }



4. INSTALL TIE ROD END SUB-ASSEMBLY


F043604
  1. Install the tie rod end onto the steering knuckle.

  1. Install the nut.

    Torque:
    91 N*m{ 928 kgf*cm , 67 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    If the holes in the cotter pin are not aligned, tighten the nut an additional 60°.



5. INSTALL FRONT STABILIZER LINK ASSEMBLY
  1. Install the front stabilizer link assembly LH to the steering knuckle with the nut.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud.



6. INSTALL FRONT AXLE HUB NUT (for 4WD)
  1. Install the hub nut.

    Torque:
    235 N*m{ 2396 kgf*cm , 174 ft.*lbf }

  1. Install the adjusting lock cap and a new cotter pin.



7. INSPECT FRONT AXLE HUB BEARING


F042746
  1. Inspect the axle hub backlash.

    1. Using a dial indicator, check the backlash near the center of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the backlash is greater than the maximum, replace the bearing.



    F042745
  1. Inspect the axle hub runout.

    1. Using a dial indicator, check the runout of the surface of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the runout is greater than the maximum, replace the bearing.



8. INSTALL FRONT AXLE HUB GREASE CAP (for 4WD)
  1. Install a front axle hub grease cap.



9. INSTALL FRONT SPEED SENSOR
  1. Install the skid control sensor wire onto the steering knuckle with the 2 bolts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Engage the clamp.

  1. Install the speed sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



10. INSTALL FRONT DISC
  1. Align the matchmarks of the disc and axle hub and install the disc.

    HINT:
    When replacing the disc, select the position that gives the minimum disc runout.



11. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY


    F050211
  1. Install the front disc brake caliper assembly with the 2 bolts.

    Torque:
    123 N*m{ 1254 kgf*cm , 91 ft.*lbf }



    F042731
  1. Install the brake tube bracket onto the steering knuckle with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



    C168981E02
  1. Using a union nut wrench, install the brake tube onto the front disc brake caliper assembly.
    Text in Illustration 
    *a
    Fulcrum Length

    Torque:
    without union nut wrench:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    with union nut wrench:
    14 N*m{ 144 kgf*cm , 10 ft.*lbf }

    NOTICE:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 22 mm (0.866 in.) (Click here).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.



12. INSTALL FRONT WHEEL

Torque:
112 N*m{ 1137 kgf*cm , 82 ft.*lbf }



13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



14. BLEED BRAKE LINE
  1. Turn the ignition switch on (IG).

  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid until the fluid level is between the MIN and MAX lines of the reservoir.

  1. Repeatedly depress the brake pedal and bleed air from the bleeder plug of the front disc brake cylinder RH.

  1. Repeat the step above until the air is completely bled, and then tighten the bleeder plug while depressing the brake pedal.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.

  1. With the brake pedal depressed, loosen the bleeder plug of the rear disc brake cylinder RH, continue to hold the brake pedal and allow brake fluid to be drained from the bleeder plug while the pump motor operates.

    HINT:
    1. Air is bled as the pump motor operates while the brake pedal is being depressed.
    2. Be sure to release the brake pedal to stop the motor after approximately 100 seconds of continuous operation.
    3. As brake fluid is continuously drained while the pump operates, it is not necessary to repeatedly depress the brake pedal.

  1. When there is no more air in the brake fluid, tighten the bleeder plug, and then release the brake pedal.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the rear disc brake cylinder LH using the same procedure as for the RH side.

  1. Turn the ignition switch off (IG).

  1. Inspect for brake fluid leaks.

  1. Check and adjust the brake fluid level .



15. CHECK VSC SENSOR SIGNAL
(Click here)


16. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)