Home › BRAKE › BRAKE › BRAKE PEDAL

BRAKE PEDAL > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE PEDAL PAD
  1. Install the brake pedal pad onto the brake pedal.



2. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER
  1. Install a new stop light switch mounting adjuster onto the pedal support.



3. INSTALL BRAKE PEDAL RETURN SPRING
  1. Apply lithium soap base glycol grease to the inner surface of the hole in the brake pedal support and brake pedal.



    F050564
  1. Install the return spring onto the brake pedal support and brake pedal.



4. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY


C225098
  1. Install the bolt and the brake pedal support.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



5. INSTALL HYDRAULIC BRAKE BOOSTER
  1. Install a new gasket onto the hydraulic brake booster.



    F050571
  1. Install the hydraulic brake booster with the 4 nuts.

    Torque:
    14 N*m{ 145 kgf*cm , 10 ft.*lbf }



    C133114E01
  1. Temporarily install each brake tube to the correct positions of the brake actuator as shown in the illustration.



    C168979E01
  1. Using a union nut wrench, connect the 4 brake tubes onto the hydraulic brake booster.

    Torque:
    without union nut wrench:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    with union nut wrench:
    14 N*m{ 144 kgf*cm , 10 ft.*lbf }

    NOTICE:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 22 mm (0.866 in.) (Click here).
    2. This torque value is effective when the union nut wrench is parallel to a torque wrench.



    F051439E01
  1. Connect the 3 connectors.



6. INSTALL MASTER CYLINDER PUSH ROD CLEVIS
  1. Apply lithium soap base glycol grease to the inner surface of the hole in the brake pedal lever.



    F050561
  1. Install the push rod clevis onto the brake pedal lever with the push rod pin and clip.



7. INSTALL STOP LIGHT SWITCH


F049043E01
  1. Insert the stop light switch into the adjuster until it just touches the brake pedal.

    NOTICE:
    Do not depress the brake pedal.



    C133112E01
  1. Make a quarter turn clockwise to install the stop light switch.

    NOTICE:
    Do not depress the brake pedal.

    HINT:
    The turning torque for installing the stop light switch:

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

  1. Check the stop light switch clearance.

    Stop light switch clearance:
    0.5 to 2.6 mm (0.020 to 0.102 in.)

  1. Connect the connector to the stop light switch.



8. BLEED BRAKE SYSTEM

CAUTION:
If air is bled without using the Techstream, damage or accidents may result. Therefore, always use the Techstream when bleeding air.

  1. Turn the ignition switch on (IG).

  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid until the fluid level is between the MIN and MAX lines of the reservoir.

  1. Repeatedly depress the brake pedal and bleed air from the bleeder plug of the front disc brake cylinder RH.

  1. Repeat the step above until the air is completely bled, and then tighten the bleeder plug while depressing the brake pedal.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.

  1. With the brake pedal depressed, loosen the bleeder plug of the rear disc brake cylinder RH, continue to hold the brake pedal and allow brake fluid to be drained from the bleeder plug while the pump motor operates.

    HINT:
    1. Air is bled as the pump motor operates while the brake pedal is being depressed.
    2. Be sure to release the brake pedal to stop the motor after approximately 100 seconds of continuous operation.
    3. As brake fluid is continuously drained while the pump operates, it is not necessary to repeatedly depress the brake pedal.

  1. When there is no more air in the brake fluid, tighten the bleeder plug, and then release the brake pedal.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the rear disc brake cylinder LH using the same procedure as for the RH side.

  1. Turn the ignition switch off and connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Air Bleeding.

    NOTICE:
    To protect the solenoid from overheating, the solenoid operation stops automatically in 4 seconds, and then the solenoid will not respond to commands for an additional 20 seconds.

  1. Repeatedly depress the brake pedal several times, and then, with the brake pedal depressed, turn FR Line on and bleed air.

    HINT:
    Air returns to the brake master cylinder reservoir together with the brake fluid and is bled from the brake system.

    NOTICE:
    1. As it is not possible to visually confirm that air is being bled, repeat this step 10 times.
    2. Do not loosen the bleeder plug.

  1. Turn FL Line on and bleed air using the same procedures as for FR Line.

  1. Turn RR Line on, loosen the bleeder plug of the rear disc brake cylinder RH and drain brake fluid.

    HINT:
    1. Do not depress the brake pedal.
    2. As brake fluid is automatically drained while the pump and solenoid operate, it is not necessary to operate the brake pedal.

  1. Repeat the step above until the air is completely bled, and then tighten the bleeder plug.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Turn RL Line on and bleed air from the bleeder plug of the rear disc brake cylinder LH using the same procedure as for the RH side.

  1. Turn the Techstream off and turn the ignition switch off.

  1. Inspect for brake fluid leaks.

  1. Check and adjust the brake fluid level (Click here).

  1. Clear the DTCs (Click here).



9. INSPECT AND ADJUST BRAKE PEDAL


F043109E01
  1. Inspect the brake pedal height.

    Pedal height from floor panel:
    168.7 to 178.7 mm (6.642 to 7.035 in.)

    If the pedal height is incorrect, adjust the rod operating adapter length.



  1. Adjust the brake pedal height.

    1. Disconnect the connector from the stop light switch.

    2. Turn the stop light switch counterclockwise, and remove the stop light switch.

    3. Remove the hydraulic brake booster (Click here).



    4. C133078E01
    5. Loosen the clevis lock nut.

    6. Adjust the rod operating adapter length by turning the pedal push rod clevis.

      Rod operating adapter length A:
      201.7 to 202.7 mm (7.941 to 7.980 in.)

    7. Tighten the clevis lock nut.

      Torque:
      26 N*m{ 260 kgf*cm , 19 ft.*lbf }

    8. Install the hydraulic brake booster (Click here).



    9. F049043E01
    10. Insert the stop light switch into the adjuster until it just touches the brake pedal.

      NOTICE:
      Do not depress the brake pedal.



    11. C133112E01
    12. Make a quarter turn clockwise to install the stop light switch.

      NOTICE:
      Do not depress the brake pedal.

      HINT:
      The turning torque for installing the stop light switch:

      Torque:
      1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

    13. Check the stop light switch clearance.

      Stop light switch clearance:
      0.5 to 2.6 mm (0.020 to 0.102 in.)

    14. Connect the connector to the stop light switch.



    F048932E01
  1. Inspect the brake pedal free play.

    1. Stop the engine and depress the brake pedal several times until there is no vacuum left in the booster.

    2. Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.

      Pedal free play:
      1.0 to 6.0 mm (0.039 to 0.236 in.)

      If incorrect, troubleshoot the brake system.



    R000934E10
  1. Inspect the brake pedal reserve distance.

    1. Release the parking brake pedal.
      With the engine running, depress the pedal and measure the pedal reserve distance as shown.

      Pedal reserve distance from floor panel at 490 N (50 kgf, 110.2 lbf):
      More than 56 mm (2.20 in.)

      If incorrect, troubleshoot the brake system.



10. INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY


    B133860
  1. Engage the 5 clips and claw and install the lower instrument panel finish panel.

  1. Connect the connector.

  1. Install the 2 <F> bolts.



11. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B133859
  1. Engage the 3 claws and install the hood lock control lever.



12. INSTALL INSTRUMENT PANEL NO. 1 REGISTER ASSEMBLY


    B133853
  1. Engage the 4 clips and 2 claws and install the instrument panel register.



13. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP
  1. Install the front door opening trim weatherstrip.



14. INSTALL COWL SIDE TRIM BOARD

HINT:
Use the same procedure as for the RH side.



15. INSTALL FOOTREST CLIP


B130588

HINT:
Use the same procedure for both sides.

  1. Engage the 2 claws and install the footrest clip.



16. INSTALL FRONT FLOOR FOOTREST


    B130589
  1. Engage the 2 studs and install the front floor footrest.



17. INSTALL FRONT DOOR SCUFF PLATE

HINT:
Use the same procedure as for the RH side.



18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }