HYDRAULIC BRAKE BOOSTER > INSTALLATION |
| 1. INSTALL HYDRAULIC BRAKE BOOSTER |
Install a new gasket onto the hydraulic brake booster.
![]() |
Install the hydraulic brake booster with the 4 nuts.
![]() |
Temporarily install each brake tube to the correct positions of the brake actuator as shown in the illustration.
![]() |
Using a union nut wrench, connect the 4 brake tubes onto the hydraulic brake booster.
![]() |
Connect the 3 connectors.
| 2. INSTALL MASTER CYLINDER PUSH ROD CLEVIS |
Apply lithium soap base glycol grease to the inner surface of the hole in the brake pedal lever.
![]() |
Install the push rod clevis onto the brake pedal lever with the push rod pin and clip.
| 3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 4. BLEED BRAKE SYSTEM |
Turn the ignition switch on (IG).
Remove the brake master cylinder reservoir filler cap assembly.
Add brake fluid until the fluid level is between the MIN and MAX lines of the reservoir.
Repeatedly depress the brake pedal and bleed air from the bleeder plug of the front disc brake cylinder RH.
Repeat the step above until the air is completely bled, and then tighten the bleeder plug while depressing the brake pedal.
Bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.
With the brake pedal depressed, loosen the bleeder plug of the rear disc brake cylinder RH, continue to hold the brake pedal and allow brake fluid to be drained from the bleeder plug while the pump motor operates.
When there is no more air in the brake fluid, tighten the bleeder plug, and then release the brake pedal.
Bleed the air from the bleeder plug of the rear disc brake cylinder LH using the same procedure as for the RH side.
Turn the ignition switch off and connect the Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn the Techstream on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Air Bleeding.
Repeatedly depress the brake pedal several times, and then, with the brake pedal depressed, turn FR Line on and bleed air.
Turn FL Line on and bleed air using the same procedures as for FR Line.
Turn RR Line on, loosen the bleeder plug of the rear disc brake cylinder RH and drain brake fluid.
Repeat the step above until the air is completely bled, and then tighten the bleeder plug.
Turn RL Line on and bleed air from the bleeder plug of the rear disc brake cylinder LH using the same procedure as for the RH side.
Turn the Techstream off and turn the ignition switch off.
Inspect for brake fluid leaks.
Check and adjust the brake fluid level (Click here).
Clear the DTCs (Click here).
| 5. INSPECT AND ADJUST BRAKE PEDAL |
![]() |
Inspect the brake pedal height.
Adjust the brake pedal height.
Disconnect the connector from the stop light switch.
Turn the stop light switch counterclockwise, and remove the stop light switch.
Remove the hydraulic brake booster (Click here).
![]() |
Loosen the clevis lock nut.
Adjust the rod operating adapter length by turning the pedal push rod clevis.
Tighten the clevis lock nut.
Install the hydraulic brake booster (Click here).
![]() |
Insert the stop light switch into the adjuster until it just touches the brake pedal.
![]() |
Make a quarter turn clockwise to install the stop light switch.
Check the stop light switch clearance.
Connect the connector to the stop light switch.
![]() |
Inspect the brake pedal free play.
Stop the engine and depress the brake pedal several times until there is no vacuum left in the booster.
Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.
![]() |
Inspect the brake pedal reserve distance.
Release the parking brake pedal.
With the engine running, depress the pedal and measure the pedal reserve distance as shown.
| 6. INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY |
![]() |
Engage the 5 clips and claw and install the lower instrument panel finish panel.
Connect the connector.
Install the 2 <F> bolts.
| 7. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Engage the 3 claws and install the hood lock control lever.
| 8. INSTALL INSTRUMENT PANEL NO. 1 REGISTER ASSEMBLY |
![]() |
Engage the 4 clips and 2 claws and install the instrument panel register.
| 9. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP |
Install the front door opening trim weatherstrip.
| 10. INSTALL COWL SIDE TRIM BOARD |
| 11. INSTALL FOOTREST CLIP |
![]() |
Engage the 2 claws and install the footrest clip.
| 12. INSTALL FRONT FLOOR FOOTREST |
![]() |
Engage the 2 studs and install the front floor footrest.
| 13. INSTALL FRONT DOOR SCUFF PLATE |
| 14. INSPECT BRAKE MASTER CYLINDER OPERATION |
Inspect the positive battery voltage.
Turn the ignition switch to OFF, and depress the brake pedal more than 20 times.
Check that the brake pedal becomes easy to depress.
If the pedal does not become easy to depress, check and replace the brake line and hydraulic brake booster.
Turn the ignition switch to ON and check the pump motor operation noise.
If the pump motor does not operate, check and replace the wire harness and pump motor .
Connect the Techstream.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Select "ACTIVE TEST" mode on the Techstream.
Check the master cylinder solenoid operation.

| Inspection Order (Step) | SOL Selected By Active Test | SOL To Be Activated |
| D | SRCF (SA1) | SMCF |
| E | SRCF & SRCR | SREA |
| F | SFRH | SFRH |
| G | SFLH | SFLH |
| H | SFRR & SFRH | SFRR |
| I | SFLR & SFLH | SFLR |
| J | SRMF (SMCF, SA3) | SREC |
| K | SRMR (SMCR, STR) | STR |
| L | SRRH | SRRH |
| M | SRLH | SRLH |
| N | SRH & SRR | SRRR |
| O | SRLR & SRLH | SRLR |
Prepare the vehicle.
Jack up and support the vehicle.
Release the parking brake lever.
Shift the shift lever to the "N" position and check that the rear wheels rotate by hand.
Inspect front VSC solenoid (SMCF) operation (step D).
Select "SRCF (SA1)" on the Techstream.
Turn the "SRCF (SA1)" on by the Techstream, then depress the brake pedal with stable force and check that the pedal cannot be depressed.
If the pedal can be depressed, replace the hydraulic brake booster.
Release the brake pedal.
When the solenoid is off, depress the brake pedal again and check that the brake pedal can be depressed.
If the pedal cannot be depressed, replace the hydraulic brake booster.
Inspect front VSC solenoid (SREA) operation (step E).
Select "SRCF & SRCR" on the Techstream.
Turn the "SRCF & SRCR" on by the Techstream, then depress the brake pedal with stable force.
When the solenoids are on, check that the front wheels do not rotate by hand.
If the front wheels rotate, replace the hydraulic brake booster.
When the solenoids are off, turn the "SRCF (SA1)" on by the intelligent, then depress the brake pedal and check the front wheels by rotating them by hand.
If the front wheels stop, replace the hydraulic brake booster.
When the "SRCF (SA1)" is off, depress the brake pedal again and check that the brake pedal can be depressed.
If the pedal cannot be depressed, replace the hydraulic brake booster.
Inspect front ABS solenoid (SFRH) operation (step F).
Select "SFRH" on the Techstream.
Turn the "SFRH" on by the Techstream, then depress the brake pedal with stable force.
When the solenoid is on, check the right front wheel by rotating it by hand.
If the right front wheel stops, replace the hydraulic brake booster.
When the solenoid is off, depress the brake pedal again and check that the right front wheel does not rotate by hand.
If the right front wheel rotates, replace the hydraulic brake booster.
Inspect front ABS solenoid (SFLH) operation (step G).
Select "SFLH" on the Techstream.
Turn the "SFLH" on by the Techstream, then depress the brake pedal with stable force.
When the solenoid is on, check the left front wheel by rotating it by hand.
If the left front wheel stops, replace the hydraulic brake booster.
When the solenoid is off, depress the brake pedal again and check that the left front wheel does not rotate by hand.
If the left front wheel rotates, replace the hydraulic brake booster.
Inspect front ABS solenoid (SFRR) operation (step H).
Select "SFRR & SFRH" on the Techstream.
Depress the brake pedal with stable force, then turn the "SFRR & SFRH" on by the Techstream.
When the solenoids are on, check the right front wheel by rotating it by hand.
If the right front wheel stops, replace the hydraulic brake booster.
When the solenoids are off, depress the brake pedal again and check that the right front wheel does not rotate by hand.
If the right front wheel rotates, replace the hydraulic brake booster.
Inspect front ABS solenoid (SFLR) operation (step I).
Select "SFLR & SFLH" on the Techstream.
Depress the brake pedal with stable force, then turn the "SFLR & SFLH" on by the Techstream.
When the solenoids are on, check the left front wheel by rotating it by hand.
If the left front wheel stops, replace the hydraulic brake booster.
When the solenoids are off, depress the brake pedal again and check that the left front wheel does not rotate by hand.
If the left front wheel rotates, replace the hydraulic brake booster.
Inspect rear VSC solenoid (SREC) operation (step J).
Select "SRMF (SMCF, SA3)" on the Techstream.
Depress the brake pedal with stable force, then turn the "SRMF (SMCF, SA3)" on by the Techstream.
Release the brake pedal when the solenoid is on, and check that the rear wheels do not rotate by hand.
If the rear wheels rotate, replace the hydraulic brake booster.
When the solenoid is off, check the rear wheels by rotating them by hand.
If the rear wheels stop, replace the hydraulic brake booster.
Inspect rear VSC solenoid (STR) operation (step K).
Select "SRMR (SMCR, STR)" on the Techstream.
Turn the "SRMR (SMCR, STR) on by the Techstream.
When the solenoid is on, check that the rear wheels rotate by hand.
If the rear wheels do not rotate, replace the hydraulic brake booster.
When the "SRMR (SMCR, STR)" is off, depress the brake pedal again and check that the rear wheels do not rotate by hand.
If the rear wheels rotate, replace the hydraulic brake booster.
Inspect rear ABS solenoid (SRRH) operation (step L).
Select "SRRH" on the Techstream.
Turn the "SRRH" on by the Techstream, then depress the brake pedal with stable force.
When the solenoid is on, check the right rear wheel by rotating it by hand.
If the right rear wheel stops, replace the hydraulic brake booster.
When the solenoid is off, depress the brake pedal again and check that the right rear wheel does not rotate by hand.
If the right rear wheel rotates, replace the hydraulic brake booster.
Inspect rear ABS solenoid (SRLH) operation (step M).
Select "SRLH" on the Techstream.
Turn the "SRLH" on by the Techstream, then depress the brake pedal with stable force.
When the solenoid is on, check the left rear wheel by rotating it by hand.
If the left rear wheel stops, replace the hydraulic brake booster.
When the solenoid is off, depress the brake pedal again and check that the left rear wheel does not rotate by hand.
If the left rear wheel rotates, replace the hydraulic brake booster.
Inspect rear ABS solenoid (SRRR) operation (step N).
Select "SRH & SRR" on the Techstream.
Depress the brake pedal with stable force, then turn the "SRH & SRR" on by the Techstream.
When the solenoids are on, check the right rear wheel by rotating it by hand.
If the right rear wheel stops, replace the hydraulic brake booster.
When the solenoids are off, depress the brake pedal again and check that the right rear wheel does not rotate by hand.
If the right rear wheel rotates, replace the hydraulic brake booster.
Inspect rear ABS solenoid (SRLR) operation (step O).
Select "SRLR & SRLH" on the Techstream.
Depress the brake pedal with stable force, then turn the "SRLR & SRLH" on by the Techstream.
When the solenoids are on, check the left rear wheel by rotating it by hand.
If the left rear wheel stops, replace the hydraulic brake booster.
When the solenoids are off, depress the brake pedal again and check that the left rear wheel does not rotate by hand.
If the left rear wheel rotates, replace the hydraulic brake booster.
Lower the vehicle.
Disconnect the Techstream.