Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Light Control Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit detects the state of the headlight dimmer switch.

WIRING DIAGRAM


E260633E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List /

  1. According to the display on the Techstream, read the "Data List".


Main Body 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Dimmer SW
Dimmer switch signal / ON or OFF
ON: Dimmer switch is ON (High Beam) or High flasher switch is ON
OFF: Dimmer switch is OFF (Low Beam) and High flasher switch is OFF
-
Passing Light SW
High flasher switch signal / ON or OFF
ON: High flasher switch is ON
OFF: High flasher switch is OFF
-
Head Light SW (Head)
Headlight switch signal / ON or OFF
ON: Light control switch is in HEAD position
OFF: Light control switch is not in HEAD position
-
Head Light SW (Tail)
Taillight switch signal / ON or OFF
ON: Light control switch is in TAIL or HEAD position
OFF: Light control switch is not in TAIL and HEAD position
-
Daytime Running Light Switch*1
DRL switch signal / ON or OFF
ON: Light control switch is in DRL position
OFF: Light control switch is not in DRL position
-
  1. *1: w/ DRL OFF function

OK:
Condition information can be displayed.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
  1. Inspect the headlight dimmer switch assembly (Click here).



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH - MAIN BODY ECU)
  1. Disconnect the E8 main body ECU connector.

  1. Disconnect the E20 headlight dimmer switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection
Condition
Specified Condition
E20-8 (HF) - E8-7 (HF)
Always
Below 1 Ω
E20-8 (HF) or E8-7 (HF) - Body ground
Always
10 kΩ or higher
E20-14 (T) - E8-8 (TAIL)
Always
Below 1 Ω
E20-14 (T) or E8-8 (TAIL) - Body ground
Always
10 kΩ or higher
E20-13 (H) - E8-1 (HEAD)
Always
Below 1 Ω
E20-13 (H) or E8-1 (HEAD) - Body ground
Always
10 kΩ or higher
E20-12 (A) - E8-3 (A)*1
Always
Below 1 Ω
E20-12 (A) or E8-3 (A) - Body ground*1
Always
10 kΩ or higher
E20-7 (HU) - E8-2 (HU)
Always
Below 1 Ω
E20-7 (HU) or E8-2 (HU) - Body ground
Always
10 kΩ or higher
E20-16 (EL) - Body ground
Always
Below 1 Ω

  1. *1: w/ DRL OFF function
  1. Reconnect the main body ECU connector.

  1. Reconnect the headlight dimmer switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)