Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1253    Pump Motor Relay

for Preparation Click here


DESCRIPTION

The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU.

DTC Code
DTC Detection Condition
Trouble Area
C1253
Open in motor system circuit (motor input circuit)
  1. ABS MTR fuse
  2. Motor relay circuit
  3. Master cylinder solenoid (Skid control ECU)

WIRING DIAGRAM

Refer to DTC C1251 .

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the hydraulic brake booster, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM (ABS MOTOR RELAY)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.

    ABS/VSC/TRAC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ABS Motor Relay
    ABS motor relay
    ABS motor relay ON or OFF
    Operation of motor can be heard

  1. Check for operation sound of the actuator motor when it is operated with the Techstream.

    OK:
    The operation sound of the actuator motor can be heard.



NG
Go to step 3
OK


2.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off

  1. Depress the brake pedal more than 40 times.

  1. Turn the ignition switch to ON.

  1. Wait until the pump motor stops.

  1. Depress the brake pedal several times until the pump motor turns on. (Procedure A)

  1. Wait until the pump stops. (Procedure B)

  1. Repeat the above steps (procedure A and B) 3 more times.

  1. Check if the same DTC is output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)  

3.INSPECT SKID CONTROL ECU TERMINAL VOLTAGE (+BM, +BM2 TERMINAL)


    C124799E54
  1. Disconnect the skid control ECU connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-2 (+BM1) - Body ground
    Always
    11 to 14 V
    A5-2 (+BM2) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM1 AND +BM2 CIRCUIT)
OK


4.INSPECT SKID CONTROL ECU (GND TERMINAL)


    C124799E53
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A4-32 (GND2) - Body ground
    Always
    Below 1 Ω
    A5-4 (GND3) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


5.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off

  1. Depress the brake pedal more than 40 times.

  1. Turn the ignition switch to ON.

  1. Wait until the pump motor stops.

  1. Depress the brake pedal several times until the pump motor turns on. (Procedure A)

  1. Wait until the pump stops. (Procedure B)

  1. Repeat the above steps (procedure A and B) 3 more times.

  1. Check if the same DTC is output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)