Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1256    Accumulator Low Pressure

for Preparation Click here


DESCRIPTION

The accumulator pressure sensor is connected to the skid control ECU in the master cylinder solenoid.

C228612E02


DTC Code
DTC Detection Condition
Trouble Area
C1256
Fluid pressure inside the accumulator drops below the specification value.
  1. Brake booster with accumulator pump assembly
  2. Master cylinder solenoid (Accumulator pressure sensor)
  3. Hydraulic brake booster assembly

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

HINT:
When DTC C1251, C1253 or C1254 is output together with DTC C1256 inspect and repair the trouble area indicated by DTC C1251, C1253 or C1254 first.

1.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Depress the brake pedal 20 times or more.

  1. Turn the ignition switch to ON.

  1. Wait for 99 seconds.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B

    HINT:
    Excessive brake pedal operation results in abnormal accumulator pressure consumption. This is normal.



B
USE SIMULATION METHOD TO CHECK (Click here)
A


2.INSPECT HYDRAULIC BRAKE BOOSTER ASSEMBLY FUNCTION
  1. Inspect brake booster pump power supply system function.

    1. Turn the ignition switch off.

    2. Depress the brake pedal 20 times or more to release the pressure in the accumulator.

      HINT:
      When the pressure is released, the brake pedal stroke becomes longer.

    3. Check that the brake fluid level is at the MAX level.

    4. Chock the 4 wheels and release the parking brake.

    5. Turn the ignition switch to ON and measure the brake booster pump operating time (the time from when the brake booster pump starts operating until it stops).

      OK:
      20 to 80 seconds

    6. Start the engine after the brake boost pump stops.

    7. Check that the ABS warning light and slip indicator light are not illuminated.

    8. Turn off the engine, and then turn the ignition switch to ON.

    9. Check that the brake boost pump operates and then stops when the brake pedal is depressed 4 or 5 times.

    10. Depress the brake pedal 4 or 5 times and measure the brake booster pump operating time (the time from when the brake booster pump starts operating until it stops).

      OK:
      2 to 11 seconds

    11. Check that the brake warning light illuminates and the buzzer sounds when the brake pedal is fully depressed continuously 15 to 20 times.

      NOTICE:
      Wait 120 seconds or more after turning the ignition switch to ON before performing this inspection.

  1. Check brake booster operation.

    1. Turn the ignition switch off.

    2. Depress the brake pedal 20 times or more to release the pressure in the accumulator.

      HINT:
      When the pressure is released, the brake pedal stroke becomes longer.

    3. Depress the brake pedal, start the engine, and check the change in the brake pedal height.

      OK:
      The brake pedal moves slightly inward.

  1. Inspect brake master cylinder fluid pressure change .



NG
Go to step 5
OK


3.READ VALUE USING TECHSTREAM (ACCUMULATOR SENSOR)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    Accumulator Sensor
    Accumulator pressure sensor reading / min.: 0 V, max.: 5 V
    3.58 to 5 V
    If value constant regardless of pump operation, accumulator pressure sensor malfunction suspected.

  1. Check that the accumulator's output value is in the Normal Condition range.

    OK:
    Accumulator pressure sensor value is in the Normal Condition.



NG
REPLACE MASTER CYLINDER SOLENOID (Click here)
OK


4.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Check if the same DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)  

5.INSPECT BRAKE BOOSTER PUMP ASSEMBLY
  1. Remove the hydraulic brake booster assembly (Click here).

  1. Using a screwdriver, remove the 2 screws and pull out the wire harness from the master cylinder solenoid.



    C173363E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Red wire terminal - Black wire terminal
    Always
    Below 2 Ω

    Text in Illustration 
    *1
    Pump motor wire harness
    *a
    Red wire
    *b
    Black wire

  1. Install the pump motor wire harness to the master cylinder solenoid with the 2 screws.

Torque:
2.9 N*m{ 30 kgf*cm , 26 in.*lbf }



NG
REPLACE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY (Click here)
OK

REPLACE HYDRAULIC BRAKE BOOSTER ASSEMBLY (Click here)