Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0722    Output Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

The speed sensor SP2 detects the rotation speed of the transmission output shaft and sends signals to the ECM. The ECM determines the vehicle speed based on these signals. An AC voltage is generated in the speed sensor SP2 coil as the parking gear mounted on the rear planetary gear assembly rotates, and this voltage is sent to the ECM. The parking gear on the rear planetary gear is used as the timing rotor for this sensor. The gear shift point and lock-up timing are controlled by the ECM based on the signals from the vehicle speed sensor and the throttle position sensor.

DTC No.
DTC Detection Conditions
Trouble Areas
P0722
All conditions below are detected 5 seconds or more continuously (2-trip detection logic).
  1. (a) No signal from speed sensor (SP2) is input to ECM while 4 pulses of No. 1 vehicle speed sensor signal are sent.
  2. (b) Vehicle speed is 9 km/h (5.6 mph) or more.
  3. (c) Transfer is in any position other than neutral position.
  1. Open or short in speed sensor (SP2) circuit
  2. Speed sensor (SP2)
  3. ECM
Reference (Using an oscilloscope):
G020664E13
Check the waveform between terminals SP2+ and SP2- of the ECM connector.

Standard:
Refer to the illustration.

Item
Condition
Terminal
SP2+ - SP2-
Tool setting
2 V/DIV, 2 ms/DIV
Vehicle condition
Vehicle speed 20 km/h (12 mph)

MONITOR DESCRIPTION

The output speed sensor monitors the output shaft speed. The ECM controls the gearshift point and the lock up timing based on the signals from the output speed sensor and throttle position sensor.
If the ECM detects no signal from the output shaft speed sensor even while the vehicle is moving, it will conclude that there is a malfunction in the output speed sensor. The ECM will illuminate the MIL and set the DTC.

MONITOR STRATEGY


Related DTCs
P0722: Speed sensor SP2/Verify pulse input
Required sensors/Components
Speed sensor SP2
Frequency of operation
Continuous
Duration
5 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present.
None
Vehicle speed at Vehicle speed sensor
9 km/h (5.6 mph) or more
Transfer neutral position switch
OFF
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


Output speed sensor signal
No signal

WIRING DIAGRAM


C186140E05


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

HINT:
According to the Data List displayed on a Techstream, you can read the values of components, such as the switches, sensors and actuators, without removing any parts. Reading the Data List as a first step of troubleshooting is one method of shortening labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are for reference only. Do not depend solely on these reference values when judging whether a part is faulty or not.

  1. Turn the ignition switch off.
  2. Connect the Techstream to the DLC3.
  3. Turn the ignition switch to ON.
  4. Turn the Techstream on.
  5. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
  6. According to the display on the Techstream, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph )
    0 km/h (0 mph): Vehicle stopped
    -

    HINT:
    1. SPD (SP2) is always 0 while driving:
      Open or short in the sensor or circuit.
    2. The SPD (SP2) value displayed on the tester is much lower than the actual vehicle speed:
      Sensor trouble, improper installation, or intermittent connection trouble of the circuit.

1.INSPECT SPEED SENSOR (SP2) INSTALLATION


    C159067E11
  1. Check the speed sensor (SP2) installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.

    Text in Illustration 
    *a
    Correct
    *b
    Incorrect
    *c
    Clearance



NG
SECURELY INSTALL OR REPLACE SPEED SENSOR (SP2)
OK


2.INSPECT SPEED SENSOR (SP2)


    C213110E01
  1. Disconnect the B38 speed sensor (SP2) connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    560 to 680 Ω

    Text in Illustration 
    *1
    Component without harness connected:
    (Speed Sensor (SP2))



NG
REPLACE SPEED SENSOR (SP2) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR (SP2) - ECM)


    C213115E02
  1. Connect the B38 speed sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B49-9 (SP2+) - B49-10 (SP2-)
    20°C (68°F)
    560 to 680 Ω
    B49-9 (SP2+) - Body ground
    Always
    10 kΩ or higher
    B49-10 (SP2-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector:
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)