DTC P0746 Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1) |
DTC P0771 Shift Solenoid "E" Performance (Shift Solenoid Valve SR) |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0746 | The gear required by the ECM does not match the actual gear when driving (2-trip detection logic) |
|
| P0771 | The gear required by the ECM does not match the actual gear when driving (2-trip detection logic) |
|
| Related DTCs | P0746: Shift solenoid valve SL1/OFF malfunction P0771: Shift solenoid valve SR/OFF malfunction Shift solenoid valve SR/ON malfunction |
| Required sensors/Components (Main) | Shift solenoid valve SL1 Shift solenoid valve SR |
| Required sensors/Components (Related) | Speed sensor (NT), Speed sensor (SP2), Crankshaft position sensor (NE) |
| Frequency of operation | Continuous |
| Duration | P0746 and P0771 OFF malfunctions (A) and (B): 0.4 seconds P0746 and P0771 OFF malfunction (C): Immediate P0771 ON malfunction: 2 cycles |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0717 (Turbine speed sensor (NT) circuit) P0722 (Output speed sensor (SP2) circuit) P0973, P0974 (Shift solenoid "A" (S1) circuit) P0976, P0977 (Shift solenoid "B" (S2) circuit) P0985, P0986 (Shift solenoid "E" (SR) circuit) P0748 (Pressure control solenoid "A" (SL1) circuit) P0778 (Pressure control solenoid "B" (SL2) circuit) P0128 (ECT (Engine Coolant Temperature) sensor circuit) P0327, P0328, P0332, P0333 (Knock sensor circuit) |
| ETCS (Electronic Throttle Control System) | Not system down |
| Transmission shift position | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT | 40°C (104°F) or more |
| Spark advance from max. retard timing by knock sensor control | 0°CA or more |
| Engine | Starting |
| Transfer range | High |
| ECM selected gear | 5th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 6.5% or more at engine speed of 2000 rpm (Conditions vary with engine speed) |
| Current ECM selected gear | 5th |
| Last ECM selected gear | 4th |
| Continuous time of ECM selecting 4th gear | 2 seconds or more |
| Current ECM selected gear | 5th |
| Last ECM selected gear | 4th |
| Current ECM selected gear | 2nd |
| Last ECM selected gear | 1st |
| Throttle valve opening angle (During transition from 1st to 2nd gear) | 1.5% or more at engine speed of 2000 rpm (Conditions vary with engine speed) |
| Turbine speed/Output speed | 0.93 to 1.07 (Actual gear is 4th) |
| Turbine speed/Output speed | No change as follows: 0.93 to 1.07 (Actual gear is 4th) ↓ 0.65 to 0.79 (Actual gear is 5th) |
| Output record from ECM for 4th → 5th up-shifting | Recorded |
| Turbine speed - Output speed x 1st gear ratio | 150 rpm or more |
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operate shift solenoid valve and set each shift position by yourself |
| Possible to check operation of shift solenoid valves [Vehicle Condition] 50 km/h (30 mph) or less |
| Gearshift controlled by ECM | 1st | 2nd | 3rd | 4th | 5th |
| Shift solenoid valve SR | OFF | OFF | OFF | OFF | ON |
| Shift solenoid valve SL1 | OFF | OFF | OFF | OFF | ON |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTCS P0746 AND P0771) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
| Only P0746 and P0771 are output Only DTC P0771 is output | A |
| P0746, P0771 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVE THE SOLENOID (SLT)) |
![]() |
Remove the test plug on the transmission case center right side and connect SST.
Connect a Techstream to the DLC3.
Start the engine and warm it up.
Measure the line pressure with SST.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
Measure the line pressure with SST.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Active the Solenoid (SLT)* | Operate the shift solenoid SLT and raise line pressure | ON or OFF
| [Vehicle Condition]
|
|
| ||||
| OK | |
| 3.INSPECT SHIFT SOLENOID VALVE SL1 |
![]() |
Remove the shift solenoid valve SL1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
| *1 | Component without harness connected: (Shift Solenoid Valve SL1) |
Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.
|
| ||||
| OK | |
| 4.INSPECT SHIFT SOLENOID VALVE SR |
![]() |
Remove the shift solenoid valve SR.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Shift solenoid SR connector - Shift solenoid SR body | 20°C (68°F) | 11 to 15 Ω |
| *1 | Component without harness connected: (Shift Solenoid Valve SR) |
Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.
|
| ||||
| OK | |
| 5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly.
|
| ||||
| OK | ||
| ||