Home › TRANSMISSION · A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0746    Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1)

DTC    P0771    Shift Solenoid "E" Performance (Shift Solenoid Valve SR)

for Preparation Click here


DESCRIPTION

The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).

DTC No.
DTC Detection Conditions
Trouble Areas
P0746
The gear required by the ECM does not match the actual gear when driving (2-trip detection logic)
  1. Shift solenoid valve SR remains open or closed
  2. Shift solenoid valve SL1 remains closed
  3. Shift solenoid valve SLT remains open or closed
  4. Valve body is blocked
  5. Automatic transmission (clutch, brake or gear, etc.)
P0771
The gear required by the ECM does not match the actual gear when driving (2-trip detection logic)
  1. Shift solenoid valve SR remains open or closed
  2. Shift solenoid valve SL1 remains open or closed
  3. Shift solenoid valve SLT remains open or closed
  4. Valve body is blocked
  5. Automatic transmission (clutch, brake or gear, etc.)

MONITOR DESCRIPTION

This DTC indicates stuck ON malfunction or stuck OFF malfunction of the shift solenoid valve SR or SL1. The ECM controls the gearshifts by turning the shift solenoid valves ON/OFF. When the gear position directed by the ECM and the actual gear position do not match, the ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0746: Shift solenoid valve SL1/OFF malfunction
P0771:
Shift solenoid valve SR/OFF malfunction
Shift solenoid valve SR/ON malfunction
Required sensors/Components (Main)
Shift solenoid valve SL1
Shift solenoid valve SR
Required sensors/Components (Related)
Speed sensor (NT), Speed sensor (SP2), Crankshaft position sensor (NE)
Frequency of operation
Continuous
Duration
P0746 and P0771 OFF malfunctions (A) and (B):
0.4 seconds
P0746 and P0771 OFF malfunction (C):
Immediate
P0771 ON malfunction:
2 cycles
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
P0717 (Turbine speed sensor (NT) circuit)
P0722 (Output speed sensor (SP2) circuit)
P0973, P0974 (Shift solenoid "A" (S1) circuit)
P0976, P0977 (Shift solenoid "B" (S2) circuit)
P0985, P0986 (Shift solenoid "E" (SR) circuit)
P0748 (Pressure control solenoid "A" (SL1) circuit)
P0778 (Pressure control solenoid "B" (SL2) circuit)
P0128 (ECT (Engine Coolant Temperature) sensor circuit)
P0327, P0328, P0332, P0333 (Knock sensor circuit)
ETCS (Electronic Throttle Control System)
Not system down
Transmission shift position
"D"
Duration time from shifting "N" to "D"
4 seconds or more
ECT
40°C (104°F) or more
Spark advance from max. retard timing by knock sensor control
0° CA or more
Engine
Starting

P0746 and P0771 OFF malfunction (A) 
ECM selected gear
5th
Vehicle speed
2 km/h (1.2 mph) or more
Throttle valve opening angle
6.5% or more at engine speed of 2000 rpm
(Conditions vary with engine speed)

P0746 and P0771 OFF malfunction (B) 
Current ECM selected gear
5th
Last ECM selected gear
4th
Continuous time of ECM selecting 4th gear
2 seconds or more

P0746 and P0771 OFF malfunction (C) 
Current ECM selected gear
5th
Last ECM selected gear
4th

P0771 ON malfunction 
Current ECM selected gear
2nd
Last ECM selected gear
1st
Throttle valve opening angle
(During transition from 1st to 2nd gear)
1.5% or more at engine speed of 2000 rpm
(Conditions vary with engine speed)

TYPICAL MALFUNCTION THRESHOLDS

[P0746 and P0771 OFF malfunction]
All of the following conditions are met: OFF malfunctions (A), (B) and (C)
2 detections are necessary in 1 driving cycle.
1st detection; temporary flag ON
2nd detection; pending fault code ON

OFF malfunction (A) 
Turbine speed/Output speed
0.93 to 1.07
(Actual gear is 4th)

OFF malfunction (B) 
Turbine speed/Output speed
No change as follows:
0.93 to 1.07 (Actual gear is 4th)
↓
0.65 to 0.79 (Actual gear is 5th)

OFF malfunction (C) 
Output record from ECM for 4th → 5th up-shifting
Recorded
[P0771 ON malfunction]
2 detections are necessary in 1 driving cycle.
1st detection; temporary flag ON
2nd detection; pending fault code ON

Turbine speed - Output speed x 1st gear ratio
150 rpm or more

INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

HINT:
Performing the Active Test using a Techstream allows components, such as the relay, VSV, and actuator, to be operated without removing any parts. Performing the Active Test as a first step of troubleshooting is one method of shortening labor time.
It is possible to display the Data List during the Active Test.
  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.
  7. According to the display on the Techstream, perform the Active Test.


HINT:
While driving, the shift position can be changed with the Techstream.
Comparing the shift position directed by the Active Test with the actual shift position enables the problem to be confirmed (Click here).

Engine and ECT 
Tester Display
Test Part
Control Range
Diagnostic Note
Control the Shift Position
Operate shift solenoid valve and set each shift position by yourself
  1. Press "→" button: Shift up
  2. Press "←" button: Shift down
Possible to check operation of shift solenoid valves
[Vehicle Condition]
50 km/h (30 mph) or less

HINT:
  1. This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
  2. The 4th to 5th up-shifting must be performed with the accelerator pedal released.
  3. The 5th to 4th down-shifting must be performed with the accelerator pedal released.
  4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
  5. The shift position directed by the ECM is shown in the Data List / Shift Status display on the Techstream.
  6. The shift solenoid valve SR and SL1 are turned on/off normally when the shift lever is in the D position:


Gearshift controlled by ECM
1st
2nd
3rd
4th
5th
Shift solenoid valve SR
OFF
OFF
OFF
OFF
ON
Shift solenoid valve SL1
OFF
OFF
OFF
OFF
ON
1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0746 AND P0771)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P0746 and P0771 are output
    Only P0771 is output
    A
    P0746 and P0771 other DTCs are output
    B

HINT:
If any codes besides P0746 and P0771 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVE THE SOLENOID (SLT))
G020657E01

NOTICE:
  1. Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F).
  2. Be careful to prevent SST's hose from interfering with the exhaust pipe.
  3. Perform the test with the A/C off.

HINT:
Performing a Techstream Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.
The Data List can be displayed during the Active Test.

  1. Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect a Techstream to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure with SST.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. According to the display on the tester, perform the Active Test.

  1. Measure the line pressure with SST.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Active the Solenoid (SLT)*
    Operate the shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Active the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    *: Active the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.

    OK:
    The line pressure changes as specified when performing the Active Test.



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


3.INSPECT SHIFT SOLENOID VALVE SL1


    C204845E01
  1. Remove the shift solenoid valve SL1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

    Text in Illustration 
    *1
    Component without harness connected:
    (Shift Solenoid Valve SL1)

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes operating sounds.



NG
REPLACE SHIFT SOLENOID VALVE SL1
OK


4.INSPECT SHIFT SOLENOID VALVE SR


    A110988E17
  1. Remove the shift solenoid valve SR.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid SR connector - Shift solenoid SR body
    20°C (68°F)
    11 to 15 Ω

    Text in Illustration 
    *1
    Component without harness connected:
    (Shift Solenoid Valve SR)

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes operating sounds.



NG
REPLACE SHIFT SOLENOID VALVE SR
OK


5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    HINT:
    Refer to Problem Symptoms Chapter 2 (Click here).

OK:
There are no foreign objects on any valves and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)