Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P2714    Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)

for Preparation Click here


DESCRIPTION


C221301E05

Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The ECM adjusts the current to shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

DTC No.
DTC Detection Conditions
Trouble Area
P2714
ECM detects malfunctions on SLT (ON side) according to the revolution difference between the turbine and the output shaft, and also by monitoring the oil pressure (2 trip detection logic).
  1. Shift solenoid valve SLT remains open or closed
  2. Shift solenoid valve S1, S2, SR, SL1 or SL2 remains open or closed
  3. 1-2 shift valve is stuck
  4. Valve body is blocked
  5. Torque converter assembly
  6. Automatic transmission (clutch, brake or gear, etc.)

MONITOR DESCRIPTION

The ECM calculates the amount of heat absorbed by the friction material based on the difference in revolution (clutch slippage) between the turbine and output shaft. The ECM turns on the MIL and outputs this DTC when the amount of heat absorption exceeds the specified value.
There are two reasons that make the revolution difference.
  1. When the shift solenoid valve SLT remains on, oil pressure goes down and clutch engagement force decreases.
  2. When the shift solenoid valve remains on or off, the gear position commanded by the ECM and the actual gear position are not the same.
NOTE: If driving continues under these conditions, the clutch will burn out and the vehicle will no longer be drivable.

MONITOR STRATEGY


Related DTCs
P2714 : Shift solenoid valve SLT/ON malfunction
Required sensors/Components (Main)
Shift solenoid valve SLT
Required sensors/Components (Related)
Valve body, ATF temperature sensor, Speed sensor (NT), Speed sensor (SP2)
Frequency of operation
Continuous
Duration
Immediate
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
P0717 (Turbine speed sensor (NT) circuit)
P0722 (Output speed sensor (SP2) circuit)
P0712, P0713, P2742, P2743 (Transmission fluid temperature sensor "A" circuit)
P0973, P0974 (Shift solenoid "A" (S1) circuit)
P0976, P0977 (Shift solenoid "B" (S2) circuit)
P0985, P0986 (Shift solenoid "E" (SR) circuit)
P0748 (Pressure control solenoid "A" (SL1) circuit)
P0778 (Pressure control solenoid "B" (SL2) circuit)
P2716 (Pressure control solenoid "D" (SLT) circuit)
P0128 (ECT (Engine Coolant Temperature) sensor circuit)
P0327, P0328, P0332, P0333 (Knock sensor circuit)
ETCS (Electronic Throttle Control System)
Not system down
Transmission shift position
"D"
ECT
40°C (104°F) or more
Spark advance from max. retard timing by knock sensor control
0° CA or more
Engine
Starting
Transfer range
High
ATF temperature
10°C (50°F) or more

TYPICAL MALFUNCTION THRESHOLDS

[P2714: ON malfunction]
  1. When one of following conditions is met: ON malfunction (A), (B), (C), (D), (E), (F) or (G)

ON malfunction (A) 
Summation of C1 clutch heat generations
Specified value

ON malfunction (B) 
Shift solenoid valve S1 ON malfunction
Detected

ON malfunction (C) 
Shift solenoid valve S2 ON malfunction
Detected

ON malfunction (D) 
Shift solenoid valve SR OFF malfunction
Detected

ON malfunction (E) 
1-2 shift valve malfunction
Detected

ON malfunction (F) 
Shift solenoid valve SL1 OFF malfunction
Detected

ON malfunction (G) 
Shift solenoid valve SL2 ON malfunction
Detected

INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2714)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P2714 is output
    A
    P2714 and other DTCs are output
    B

    HINT:
    If any codes besides P2714 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVE THE SOLENOID (SLT))
G020657E01

NOTICE:
  1. Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F).
  2. Be careful to prevent SST's hose from interfering with the exhaust pipe.
  3. Perform the test with the A/C off.

HINT:
Performing a Techstream Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.
The Data List can be displayed during the Active Test.

  1. Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect a Techstream to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure with SST.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

  1. Measure the line pressure with SST.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Active the Solenoid (SLT)*
    Operate the shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Active the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    *: Active the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.

    OK:
    The line pressure changes as specified when performing the Active Test.



NG
Go to step 7
OK


3.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE SHIFT POSITION)

CAUTION:
This test should always be performed with at least 2 people.

NOTICE:
  1. Perform the test at the normal operating ATF temperature: 50 to 80°C (122 to 176°F).
  2. Perform the test with the A/C turned off.

  1. Connect the Techstream to the DLC3.

  1. Clear the DTC (Click here).

  1. Warm up the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

HINT:
While driving, the shift position can be forcibly changed with the Techstream.


Engine and ECT 
Tester Display
Test Part
Control Range
Diagnostic Note
Control the Shift Position
Operate shift solenoid valve and set each shift position by yourself
  1. Press "→" button: Shift up
  2. Press "←" button: Shift down
Possible to check operation of shift solenoid valves
[Vehicle Condition]
50 km/h (30 mph) or less

HINT:
  1. This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
  2. The 4th to 5th up-shift must be performed with the accelerator pedal released.
  3. The 5th to 4th down-shift must be performed with the accelerator pedal released.
  4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
  5. The shift position commanded by the ECM is shown in the Data List / Shift Status display on the Techstream.

  1. Compare the ECM gear shift command and the actual gear position.

    OK:
    Gear position changes in accordance with the Techstream command.


    Result 
    System Condition
    ECM gear shift command
    Proceed to
    1st
    2nd
    3rd
    4th
    5th
    Actual gear position under malfunction
    Shift solenoid S1
    Stuck ON
    1st
    2nd
    2nd
    1st
    N*1
    A
    Stuck OFF
    4th
    3rd
    3rd
    4th
    5th
    Shift solenoid S2
    Stuck ON*2
    2nd
    2nd
    3rd
    3rd
    N*1
    B
    Stuck OFF*3
    1st
    1st
    4th
    4th
    5th
    Shift solenoid SL2
    Stuck ON
    1st
    2nd
    3rd
    4th
    N*1
    C
    Stuck OFF
    1st
    2nd
    3rd
    4th
    5th
    Shift solenoid SR
    Stuck ON*4
    1st
    2nd
    3rd
    4th
    5th
    D
    Stuck OFF*5
    1st
    2nd
    3rd
    4th
    4th
    Normal
    1st
    2nd
    3rd
    4th
    5th
    E

    HINT:
    1. *1: Neutral
    2. *2: When shift solenoid S2 is stuck ON, the vehicle cannot drive in reverse.
    3. *3: When shift solenoid S2 is stuck OFF, the 4th to 5th up-shift will have a large shift shock. Also the 5th to 4th down-shift will have time lag.
    4. *4: Stuck ON condition can be determined by checking if shift shock has increased excessively.
    5. *5: When shift solenoid SR is stuck OFF, moving the shift lever from N to D will cause a large shift shock.
    6. Gear shift can be determined by paying attention to changes in rpm.



B
Go to step 10

C
Go to step 13

D
Go to step 16

E
Go to step 20
A


4.INSPECT SHIFT SOLENOID VALVE S1


    A110986E12
  1. Remove the shift solenoid valve S1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid S1 connector - Shift solenoid S1 body
    20°C (68°F)
    11 to 15 Ω

    Text in Illustration 
    *1
    Component without harness connected:
    (Shift Solenoid S1)

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes operating sounds.



NG
REPLACE SHIFT SOLENOID VALVE S1
OK


5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    HINT:
    Refer to Problem Symptoms Table Chapter 2 (Click here).

OK:
There are no foreign objects on any valves and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


6.INSPECT TORQUE CONVERTER ASSEMBLY
  1. Check the torque converter assembly (Click here).

    OK:
    The torque converter operates normally.



NG
REPLACE TORQUE CONVERTER ASSEMBLY
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)  

7.INSPECT SHIFT SOLENOID VALVE SLT


    C204845E01
  1. Remove the shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

    Text in Illustration 
    *1
    Component without harness connected:
    (Shift Solenoid Valve SLT)

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes operating sounds.



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


8.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    HINT:
    Refer to Problem Symptoms Table Chapter 2 (Click here).

OK:
There are no foreign objects on any valves and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


9.INSPECT TORQUE CONVERTER ASSEMBLY
  1. Check the torque converter assembly (Click here).

    OK:
    The torque converter operates normally.



NG
REPLACE TORQUE CONVERTER ASSEMBLY
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)  

10.INSPECT SHIFT SOLENOID VALVE S2


    A110987E17
  1. Remove the shift solenoid valve S2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid S2 connector - Shift solenoid S2 body
    20°C (68°F)
    11 to 15 Ω

    Text in Illustration 
    *1
    Component without harness connected:
    (Shift Solenoid Valve S2)

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes operating sounds.



NG
REPLACE SHIFT SOLENOID VALVE S2
OK


11.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    HINT:
    Refer to Problem Symptoms Table Chapter 2 (Click here).

OK:
There are no foreign objects on any valves and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


12.INSPECT TORQUE CONVERTER ASSEMBLY
  1. Check the torque converter assembly (Click here).

    OK:
    The torque converter operates normally.



NG
REPLACE TORQUE CONVERTER ASSEMBLY
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)  

13.INSPECT SHIFT SOLENOID VALVE SL2


    C204845E01
  1. Remove the shift solenoid valve SL2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

    Text in Illustration 
    *1
    Component without harness connected:
    (Shift Solenoid Valve SL2)

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes operating sounds.



NG
REPLACE SHIFT SOLENOID VALVE SL2
OK


14.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    HINT:
    Refer to Problem Symptoms Table Chapter 2 (Click here).

OK:
There are no foreign objects on any valves and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


15.INSPECT TORQUE CONVERTER ASSEMBLY
  1. Check the torque converter assembly (Click here).

    OK:
    The torque converter operates normally.



NG
REPLACE TORQUE CONVERTER ASSEMBLY
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)  

16.INSPECT SHIFT SOLENOID VALVE SR


    A110988E17
  1. Remove the shift solenoid valve SR.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid SR connector - Shift solenoid SR body
    20°C (68°F)
    11 to 15 Ω

    Text in Illustration 
    *1
    Component without harness connected:
    (Shift Solenoid Valve SR)

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes operating sounds.



NG
REPLACE SHIFT SOLENOID VALVE SR
OK


17.INSPECT SHIFT SOLENOID VALVE SL1


    C204845E01
  1. Remove the shift solenoid valve SL1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

    Text in Illustration 
    *1
    Component without harness connected:
    (Shift Solenoid Valve SL1)

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes operating sounds.



NG
REPLACE SHIFT SOLENOID VALVE SL1
OK


18.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    HINT:
    Refer to Problem Symptoms Table Chapter 2 (Click here).

OK:
There are no foreign objects on any valves and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


19.INSPECT TORQUE CONVERTER ASSEMBLY
  1. Check the torque converter assembly (Click here).

    OK:
    The torque converter operates normally.



NG
REPLACE TORQUE CONVERTER ASSEMBLY
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)  

20.INSPECT SHIFT SOLENOID VALVE SLT


    C204845E01
  1. Remove the shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

    Text in Illustration 
    *1
    Component without harness connected:
    (Shift Solenoid Valve SLT)

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes operating sounds.



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


21.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    HINT:
    Refer to Problem Symptoms Table Chapter 2 (Click here).

OK:
There are no foreign objects on any valves and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


22.INSPECT TORQUE CONVERTER ASSEMBLY
  1. Check the torque converter assembly (Click here).

    OK:
    The torque converter operates normally.



NG
REPLACE TORQUE CONVERTER ASSEMBLY
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)