Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0781    1-2 Shift (1-2 Shift Valve)

for Preparation Click here


DESCRIPTION

The 1-2 shift valve performs shifting to 1st gear and other gears.

DTC No.
DTC Detection Conditions
Trouble Areas
P0781
Gear required by the ECM does not match the actual gear when driving. (2-trip detection logic)
  1. Valve body is blocked up or stuck (1-2 shift valve)
  2. Shift solenoid valve SLT remains open or closed
  3. Automatic transmission (clutch, brake or gear, etc.)

MONITOR DESCRIPTION

This DTC indicates that the 1-2 shift valve in the valve body is locked in the direction of the spring compression. The ECM controls the gearshifts by turning the shift solenoid valves ON/OFF and switching oil pressure to the valves in the valve body.
The ECM calculates the actual transmission gear by comparing the signals from the input speed sensor (NT) and the output speed sensor (SP2). The ECM can detect many mechanical problems in the shift solenoids, valve body, and the transmission clutches, brakes, and gears. If the ECM detects that the actual gear position and the commanded gear position are different, it will illuminate the MIL and store the DTC.

MONITOR STRATEGY


Related DTCs
P0781: Valve body/Rationality check
Required sensors/Components (Main)
Valve body
Required sensors/Components (Related)
Automatic transmission assembly, Speed sensor (NT), Speed sensor (SP2), Vehicle speed sensor, Throttle position sensor
Frequency of operation
Continuous
Duration
Conditions (A) and (B)
0.4 seconds
Condition (C)
3 seconds
Condition (D)
0.5 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
P0717 (Turbine speed sensor (NT) circuit)
P0722 (Output speed sensor (SP2) circuit)
P0973, P0974 (Shift solenoid "A" (S1) circuit)
P0976, P0977 (Shift solenoid "B" (S2) circuit) )
P0985, P0986 (Shift solenoid "E" (SR) circuit
P0748 (Pressure control solenoid "A" (SL1) circuit)
P0778 (Pressure control solenoid "B" (SL2) circuit)
P0128 (ECT (Engine Coolant Temperature) sensor circuit)
P0327, P0328, P0332, P0333 (Knock sensor circuit
ETCS (Electronic Throttle Control System)
Not system down
Transmission shift position
"D"
Duration time from shifting "N" to "D"
4 seconds or more
ECT
40°C (104°F) or more
Spark advance from max. retard timing by knock sensor control
0°CA or more
Engine
Starting

Condition (A) 
ECM selected gear
2nd
Vehicle speed
2 km/h (1.2 mph) or more
Output speed
2nd → 1st down shift point or more
Throttle valve opening angle
6.5% or more at engine speed of 2000 rpm
(Conditions vary with engine speed)

Condition (B) 
ECM selected gear
4th
Vehicle speed
2 km/h (1.2 mph) or more
Throttle valve opening angle
6.5% or more at engine speed of 2000 rpm
(Conditions vary with engine speed)

Condition (C) 
Current ECM selected gear
5th
Last ECM selected gear
4th
Vehicle speed
(During transition from 4th to 5th gear)
Less than 100 km/h (62.2 mph)

Condition (D) 
ECM selected gear
5th
Engine speed - Turbine speed (NE - NT)
(After transition from 4th to 5th gear)
150 rpm or less
Vehicle speed
(After transition from 4th to 5th gear)
Less than 100 km/h (62.2 mph)

TYPICAL MALFUNCTION THRESHOLDS

Condition (A) and Conditions (B), (C) or (D) are met:

Condition (A) 
Turbine speed/Output speed
3.30 to 7.50
(Actual gear is 1st)

Condition (B) 
Turbine speed/Output speed
1.28 to 1.53
(Actual gear is 3rd)

Condition (C) 
Turbine speed - Output speed x 4th gear ratio
1000 rpm or more

Condition (D) 
Turbine speed - Output speed x 5th gear ratio
1000 rpm or more

INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0781)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P0781 is output
    A
    P0781 and other DTCs
    B

    HINT:
    If any codes besides P0781 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE SHIFT POSITION)

HINT:
Performing the Active Test using a Techstream allows components, such as the relay, VSV, and actuator, to be operated without removing any parts. Performing the Active Test as a first step of troubleshooting is one method of shortening labor time.
It is possible to display the Data List during the Active Test.
  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.
  7. According to the display on the Techstream, perform the Active Test.

HINT:
While driving, the shift position can be changed with the Techstream.
Comparing the shift position directed by the Active Test with the actual shift position enables the problem to be confirmed (Click here).


Engine and ECT 
Tester Display
Test Part
Control Range
Diagnostic Note
Control the Shift Position
Operate shift solenoid valve and set each shift position by yourself
  1. Press "→" button: Shift up
  2. Press "←" button: Shift down
Possible to check operation of shift solenoid valves
[Vehicle Condition]
50 km/h (30 mph) or less

HINT:
  1. This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
  2. The 4th to 5th up-shifting must be performed with the accelerator pedal released.
  3. The 5th to 4th down-shifting must be performed with the accelerator pedal released.
  4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
  5. The shift position directed by the ECM is shown in the Data List / Shift Status display on the Techstream.
  6. Gear positions in the event of a solenoid valve mechanical problem:

    Gearshift operated by tester
    1st
    2nd
    3rd
    4th
    5th
    Actual gear position under malfunction
    1st
    1st
    3rd
    3rd
    N*
    N*: Neutral

    OK:
    Gear position changes in accordance with the tester operation.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


3.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVE THE SOLENOID (SLT))
G020657E01

NOTICE:
  1. Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F).
  2. Be careful to prevent SST's hose from interfering with the exhaust pipe.
  3. Perform the test with the A/C off.

HINT:
Performing a Techstream Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.
The Data List can be displayed during the Active Test.

  1. Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect a Techstream to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure with SST.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. According to the display on the tester, perform the Active Test.

  1. Measure the line pressure with SST.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Active the Solenoid (SLT)*
    Operate the shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Active the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    *: Active the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.

    OK:
    The line pressure changes as specified when performing the Active Test.



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


4.CLEAR DTC AND PERFORM RUNNING TEST
  1. Clear the DTC (Click here).

  1. Check for the DTC again after conducting the Monitor Drive Pattern (Click here).

    OK:
    No DTC code output.



NG
REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)
OK

END