DTC P2742 Transmission Fluid Temperature Sensor "B" Circuit Low Input |
DTC P2743 Transmission Fluid Temperature Sensor "B" Circuit High Input |
| No. 2 ATF Temperature Sensor Status | Detection Condition | Symptom | Recovery Condition |
| Sensor is normal |
|
|
|
|
|
| |
When the conditions (a) and (b) are satisfied continually
|
|
| |
| Sensor is short |
|
|
|
|
|
|
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P2742 | No. 2 ATF temperature sensor resistance (voltage) is less than 25 Ω (0.046 V) for 0.5 seconds or more (1-trip detection logic). |
|
| P2743 | No. 2 ATF temperature sensor resistance is more than 156 kΩ (4.915 V) for 0.5 seconds or more, and either of the following conditions is met (1-trip detection logic): |
|
| (A) 15 minutes or more have elapsed after the engine start when engine coolant temperature or intake air temperature is -29.375°C (-20.875°F) or less. | ||
| (B) 10 seconds or more have elapsed after the engine start when engine coolant temperature and intake air temperature are more than -29.375°C (-20.875°F). |

| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| A/T Oil Temperature 2 | No. 2 ATF Temperature Sensor Value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If the value is "-40°C (-40°F)" or "150°C (302°F) or more", No. 2 ATF temperature sensor circuit is open or short. |
| Temperature Displayed | Malfunction |
| -40°C (-40°F) | Open circuit |
| 150°C (302°F) or more | Short circuit |
| 1.INSPECT TRANSMISSION WIRE (NO. 2 ATF TEMPERATURE SENSOR) |
![]() |
Disconnect the transmission wire connector from the transmission.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (OT2-) - 9 (OT2+) | Always | 79 Ω to 156 kΩ |
| 1 (OT2-) - Body ground | Always | 10 kΩ or higher |
| 9 (OT2+) - Body ground | Always | 10 kΩ or higher |
| *1 | Component without harness connected: (Transmission Wire) |
| ATF Temperature | Specified Condition |
| 10°C (50°F) | 5 to 8 kΩ |
| 25°C (77°F) | 2.5 to 4.5 kΩ |
| 110°C (230°F) | 0.22 to 0.28 kΩ |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM) |
![]() |
Connect the transmission wire connector to the transmission.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B49-11 (THO2) - B48-8 (ETHW) | Always | 79 Ω to 156 kΩ |
| B49-11 (THO2) - Body ground | Always | 10 kΩ or higher |
| B48-8 (ETHW) - Body ground | Always | 10 kΩ or higher |
| *1 | Rear view of wire harness connector: (to ECM) |
|
| ||||
| OK | ||
| ||