Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P2772    Four Wheel Drive (4WD) Low Switch Circuit Range / Performance

for Preparation Click here


DESCRIPTION

The ECM detects the signal from the No. 1 transfer indicator switch (Transfer L4 position switch).
This DTC indicates that the No. 1 transfer indicator switch remains ON.

DTC No.
DTC Detection Conditions
Trouble Areas
P2772
No. 1 transfer indicator switch remains ON while vehicle running under following conditions for 1.8 seconds or more (1-trip detection logic).
  1. (a) Output shaft speed: between 1000 rpm and 3000 rpm.
  2. (b) Transfer high and low shift lever position: H.
  1. Short in No. 1 transfer indicator switch (Transfer L4 position switch) circuit
  2. No. 1 transfer indicator switch
  3. ECM

MONITOR DESCRIPTION

The ECM monitors the No. 1 transfer indicator switch to determine whether the transfer-case L4 gear is engaged. If the transfer-case L4 gears remain engaged under the following conditions, the ECM determines that there is a malfunction of the No. 1 transfer indicator switch:
  1. No. 1 transfer indicator switch indicates that the L4 transfer-case gears are engaged.
  2. Transfer high and low shift lever is in the "H" position.
  3. Transfer-case output shaft rpm is between 1000 and 3000 rpm.
  4. The specified time period has elapsed.
If all of the above conditions are met, the ECM determines that there is a malfunction of the No. 1 transfer indicator switch, illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P2772 : Transfer L4 position switch/ON malfunction
Required sensors/Components
No. 1 transfer indicator switch (Transfer L4 position switch)
Frequency of operation
Continuous
Duration
ON malfunction (A)
1.8 seconds
ON malfunction (B)
0.5 seconds
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS

The following conditions are common to ON malfunctions (A) and (B).

The monitor will run whenever the following DTCs are not present
P0500 (Vehicle speed sensor "A" circuit)
P0722 (Output speed sensor (SP2) circuit)
Transmission neutral position switch
OFF

ON malfunction (A) 
Output speed (Transfer output speed)
1000 to 3000 rpm

ON malfunction (B) 
Output speed (Transfer output speed)
143 rpm or more

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met: ON malfunctions (A) and (B).

ON malfunction (A) 
No. 1 transfer indicator switch
ON

ON malfunction (B) 
Actual transfer gear ratio
Transfer input speed/Transfer output speed
0.9 to 1.1

WIRING DIAGRAM


C189658E02


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

1.INSPECT NO. 1 TRANSFER INDICATOR SWITCH (TRANSFER L4 POSITION SWITCH)


    G034535E03
  1. Remove the No. 1 transfer indicator switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Not pushed
    10 kΩ or higher
    1 - 2
    Pushed
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected:
    (No. 1 Transfer Indicator Switch)
    *a
    Push



NG
REPLACE NO. 1 TRANSFER INDICATOR SWITCH
OK


2.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 TRANSFER INDICATOR SWITCH - BODY GROUND)


    C213112E01
  1. Install the No. 1 transfer indicator switch.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E78-16 (L4) - Body ground
    Except L position
    10 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector:
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)