Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0550    Power Steering Pressure Sensor Circuit Malfunction

DTC    P0552    Power Steering Pressure Sensor Circuit Low Input

DTC    P0553    Power Steering Pressure Sensor Circuit High Input

for Preparation Click here


DESCRIPTION

The power steering oil pressure switch (sensor) is turned on when a power steering wheel load occurs by turning the steering wheel. The ECM regulates the engine idling speed according to the voltage output of the sensor.

DTC No.
DTC Detection Condition
Trouble Area
P0550
Power steering oil pressure switch (sensor) voltage less than 0.28 V, or more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic)
  1. Open or short in power steering oil pressure sensor circuit
  2. Power steering oil pressure switch
  3. ECM
P0552
Power steering oil pressure switch (sensor) voltage less than 0.28 V for 0.5 seconds while engine running.
(1 trip detection logic)
  1. Open or short in power steering oil pressure sensor circuit
  2. Power steering oil pressure switch
  3. ECM
P0553
Power steering oil pressure switch (sensor) voltage more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic)
  1. Open or short in power steering oil pressure sensor circuit
  2. Power steering oil pressure switch
  3. ECM

MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to regulate the engine idling speed. When the sensor output voltage deviates from the normal operating range, the ECM determines that there is a malfunction in the power steering oil pressure switch and stores DTC(s).

MONITOR STRATEGY


Related DTCs
P0550: Power steering pressure sensor range check (Chattering)
P0552: Power steering pressure sensor range check (Low voltage)
P0553: Power steering pressure sensor range check (High voltage)
Required Sensors/Components (Main)
Power steering pressure sensor
Frequency of operation
Continuous
Duration
0.5 seconds
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Time after starter ON to OFF
2 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


P0550: 
Power steering pressure sensor voltage
Less than 0.28 V, or more than 4.9 V

P0552: 
Power steering pressure sensor voltage
Less than 0.28 V

P0553: 
Power steering pressure sensor voltage
More than 4.9 V

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine.
  7. Idle the engine for 5 seconds [A].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  9. Read DTCs.

    HINT:
    1. If a DTC is output, the system is malfunctioning.
    2. If a DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0550, P0552 or P0553.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.

  13. If no DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A226834E03


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (POWER STEERING OIL PRESSURE SWITCH - ECM)
  1. Disconnect the power steering oil pressure switch connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B59-2 (PSP) - B48-16 (PSP)
    Always
    Below 1 Ω
    B59-1 (VC) - B47-16 (VCV2)
    Always
    Below 1 Ω
    B59-3 (E2) - B48-8 (ETHW)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B59-2 (PSP) or B48-16 (PSP) - Body ground
    Always
    10 kΩ or higher
    B59-1 (VC) or B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE POWER STEERING OIL PRESSURE SWITCH
  1. Replace the power steering oil pressure switch (Click here).


NEXT


3.CONFIRM WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0550, P0552 and/or P0553 are output
    A
    No output
    B



B
END
A

REPLACE ECM (Click here)