Home › TRANSMISSION · A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0717    Input Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

This sensor detects the rotation speed of the turbine which shows the input revolution of the transmission. By comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (SP2), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, providing smooth gear shifts.

DTC No.
DTC Detection Conditions
Trouble Areas
P0717
All conditions below are detected for 5 seconds or more (1-trip detection logic).
  1. (a) Gear change is not being performed.
  2. (b) Gear position: 4th or 5th.
  3. (c) T/M input shaft speed: 300 rpm or less.
  4. (d) T/M output shaft speed: 1000 rpm or more.
  5. (e) Park/neutral position switch (NSW, R and L) is OFF.
  6. (f) Shift solenoid valves, park/neutral position switch and vehicle speed sensor are in normal operation.
  1. Open or short in speed sensor (NT) circuit
  2. Speed sensor (NT)
  3. ECM
Reference (Using an oscilloscope):
G020663E07
Check the waveform between terminals NT+ and NT- of the ECM connector.

Standard:
Refer to the illustration.

Item
Condition
Terminal
NT+ - NT-
Tool setting
2 V/DIV, 2 ms/DIV
Vehicle condition
Engine idling speed (P or N position)

MONITOR DESCRIPTION

This DTC indicates that a pulse is not output from the speed sensor NT (Turbine (input) speed sensor) or is weak. The NT terminal of the ECM detects the revolution signal from the speed sensor (NT) (input speed). The ECM outputs a gearshift signal comparing the input speed sensor (NT) with the output speed sensor (SP2). While the vehicle is operating in the 4th or 5th gear position in the shift position of D, if the input shaft revolution is less than 300 rpm*1 although the output shaft revolution is more than 1,000 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.
*1: Pulse is not output or is irregularly output.
*2: The vehicle speed is approximately 50 km/h (31 mph) or more.

MONITOR STRATEGY


Related DTCs
P0717: Speed sensor (NT)/Verify pulse input
Required sensors/Components (Main)
Speed sensor (NT)
Required sensors/Components (Related)
Speed sensor (SP2)
Frequency of operation
Continuous
Duration
5 seconds
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present.
P0746, P0748: Shift solenoid valve SL1
P0776, P0778: Shift solenoid valve SL2
P0751, P0973, P0974: Shift solenoid valve S1
P0756, P0976, P0977: Shift solenoid valve S2
Shift change
Each shift change is completed before starting next shift change operation
ECM selected gear
4th or 5th
Output shaft revolution
1000 rpm or more
R switch
OFF
L switch
OFF
Engine
Running
Transmission range switch fail (P0705)
Not Detected
Ignition Switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


Turbine speed sensor revolution
Less than 300 rpm

COMPONENT OPERATING RANGE


Speed sensor (NT)
Input speed is equal to engine speed when lock-up ON

WIRING DIAGRAM


C186140E04


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

HINT:
According to the Data List displayed on a Techstream, you can read the values of components, such as the switches, sensors and actuators, without removing any parts. Reading the Data List as a first step of troubleshooting is one method of shortening labor time.

  1. Warm up the engine.
  2. Turn the ignition switch to OFF.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
  7. According to the display on the Techstream, read the Data List.

Engine and ECT 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
SPD (NT)
Input Turbine Speed/
Min.: 0 rpm
Max.: 12750 rpm
[HINT]
  1. Lock-Up ON (After warming up the engine):
    Input turbine speed (NT) equal to the engine speed.
  2. Lock-Up OFF (Idling in N position):
    Input turbine speed (NT) nearly equal to the engine speed.
Data is displayed in increments of 50 rpm

HINT:
  1. SPD (NT) is always 0 while driving:
    Open or short in the sensor or circuit.
  2. SPD (NT) is always less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:
    Sensor trouble, improper installation, or intermittent connection trouble of the circuit.

1.INSPECT SPEED SENSOR (NT) INSTALLATION


    C159067E11
  1. Check the speed sensor (NT) installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.

    Text in Illustration 
    *a
    Correct
    *b
    Incorrect
    *c
    Clearance



NG
SECURELY INSTALL OR REPLACE SPEED SENSOR (NT)
OK


2.INSPECT SPEED SENSOR (NT)


    C213110E01
  1. Disconnect the speed sensor (NT) connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    560 to 680 Ω

    Text in Illustration 
    *1
    Component without harness connected:
    (Speed Sensor (NT))



NG
REPLACE SPEED SENSOR (NT) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR (NT) - ECM)


    C213115E01
  1. Connect the speed sensor (NT) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B49-3 (NT+) - B49-4 (NT-)
    20°C (68°F)
    560 to 680 Ω
    B49-3 (NT+) - Body ground
    Always
    10 kΩ or higher
    B49-4 (NT-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector:
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)