Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Warning Buzzer does not Sound

for Preparation Click here


DESCRIPTION

The combination meter assembly controls the buzzers in accordance with signals from the front seat inner belt assembly LH, center airbag sensor assembly and the main body ECU.

WIRING DIAGRAM


B322125E01


INSPECTION PROCEDURE

1.CHECK BUZZER (SEAT BELT, KEY REMINDER)
  1. Check that the seat belt and key reminder buzzers sound.
    Result 
    Result
    Proceed to
    Seat belt warning buzzer does not sound (Driver side)
    A
    Seat belt warning buzzer does not sound (Passenger side)
    B
    Key reminder warning buzzer does not sound
    C
    No warning buzzers sound
    D

    HINT:
    1. Seat belt warning buzzer on: Ignition switch is ON, driver or front passenger seat belt is unfastened, and vehicle speed is 20 km/h (12.4 mph) or more.
    2. Key reminder warning buzzer on: Ignition switch is OFF, key is in ignition key cylinder, and driver side door is open.



B
Go to step 5

C
GO TO KEY REMINDER WARNING SYSTEM (Click here)

D
REPLACE COMBINATION METER ASSEMBLY (Click here)
A


2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)
  1. Disconnect the L25 front seat inner belt assembly (driver side) connector.



    E258785E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 2 (E)
    Tongue plate fastened
    10 k Ω or higher
    1 (+) - 2 (E)
    Tongue plate unfastened
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front Seat Inner Belt Assembly (Driver Side))

  1. Reconnect the front seat inner belt assembly (driver side) connector.



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY)
  1. Disconnect the E13 combination meter assembly connector.

  1. Disconnect the L25 front seat inner belt assembly (driver side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E13-8 (L) - L25-1 (+)
    Always
    Below 1 Ω

  1. Reconnect the combination meter assembly connector.

  1. Reconnect the front seat inner belt assembly (driver side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY - BODY GROUND)
  1. Disconnect the L25 front seat inner belt assembly (driver side) connector.



    E258786E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L25-2 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly (Driver Side))

  1. Reconnect the front seat inner belt assembly (driver side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

5.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output (Click here)
    Result 
    Result
    Proceed to
    CAN communication DTC is not output
    A
    CAN communication DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


6.CHECK SUPPLEMENTAL RESTRAINT SYSTEM
  1. Check if a supplemental restraint DTC is output (Click here).
    Result 
    Result
    Proceed to
    Supplemental restraint DTC is not output
    A
    Supplemental restraint DTC is output
    B



B
GO TO SUPPLEMENTAL RESTRAINT SYSTEM (Click here)
A


7.CHECK OCCUPANT CLASSIFICATION SYSTEM
  1. Check if a occupant classification DTC is output (Click here).
    Result 
    Result
    Proceed to
    Occupant classification DTC is not output
    A
    Occupant classification DTC is output
    B



B
GO TO OCCUPANT CLASSIFICATION SYSTEM (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)