Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › FRONT SEAT SIDE AIRBAG ASSEMBLY

FRONT SEAT SIDE AIRBAG ASSEMBLY > REMOVAL

for Preparation Click here


NOTICE:
  1. Be sure to read precaution thoroughly before servicing (Click here).
  2. Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.
  3. If the front seat side airbag assembly was deployed, replace the front seat side airbag assembly, front seat adjuster sub-assembly, front seatback cover and front seatback pad with the necessary parts in accordance with the extent of the collision damage (Click here).

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.



2. REMOVE FRONT SEAT TRACK COVER


B130664E01

HINT:
Use the same procedure for both sides.

  1. Insert a flat- head screwdriver (diameter: approximately above 5 mm (0.197 in.)) between the front seat track cover inside claw lower part and floor mat.

  1. Place an object with a height of approximately 5 to 8 mm (0.197 to 0.315 in.) below the screwdriver. Use the object as the screwdriver fulcrum and push down on the screwdriver to remove the front seat track cover inside claw, as shown in the illustration.
    Specification: 
    Area
    Measurement
    a
    1.6 mm (0.063 in.)
    b
    5.0 mm (0.197 in.)
    c
    5.0 to 8.0 mm (0.197 to 0.315 in.)



    B138596E01
  1. Lift up on the area where the claw was removed. Then push in the direction of the claw on the opposite side to remove the outside claw.



    B138597E01
  1. After the 2 claws have been removed, carefully pull the front seat track cover rearward and remove the front seat track cover.



3. REMOVE FRONT SEAT ASSEMBLY


    B135117E01
  1. for Driver Side:

    1. Using a clip remover, remove the clamp.

    2. Disconnect the 2 buckle switch connectors.

    3. Slide the slider and disconnect the airbag connector.



    B135119E01
  1. for Front Passenger Side:

    1. Using a clip remover, remove the clamp.

    2. Disconnect the connector.

    3. Slide the slider and disconnect the airbag connector.



    B130665
  1. Move the front seat to the most forward position.

  1. Remove the 2 bolts from the rear side.

  1. Move the front seat to the most rearward position.

  1. Remove the 2 bolts from the front side.

  1. Remove the front seat.



4. DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER


    B130680
  1. Disconnect the 2 front seatback cover bands.



5. REMOVE VERTICAL SEAT ADJUSTER HANDLE COVER (for Driver Side)


    B130670E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the vertical seat adjuster handle cover.



6. REMOVE VERTICAL SEAT ADJUSTER HANDLE (for Driver Side)


    B130672
  1. Remove the 2 screws and the vertical seat adjuster handle.



7. REMOVE RECLINING ADJUSTER RELEASE HANDLE


    B130673E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the reclining adjuster release handle.



8. REMOVE FRONT SEAT CUSHION OUTER SHIELD


    B130675E01
  1. Remove the screw.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and the clip and remove the front seat cushion outer shield.



9. REMOVE FRONT SEAT INNER BELT ASSEMBLY


    B130776
  1. for Driver Side:

    1. Disconnect the seat position sensor connector.

    2. Using a clip remover, remove the 2 connectors and the clamp.

    3. Remove the clamp.



    B130779
  1. for Front Passenger Side:

    1. Disconnect the buckle switch connector.

    2. Using a clip remover, remove the connector and the clamp.



    B130777
  1. Remove the wire harness from the claw of the front seat cushion inner shield.

  1. Remove the nut and the front seat inner belt.



10. REMOVE FRONT SEAT CUSHION INNER SHIELD


    B130677E01
  1. Remove the screw.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and the clip and remove the front seat cushion inner shield.



11. REMOVE FRONT SEAT HEADREST ASSEMBLY


    B130684E01
  1. Push in the lock button of the front seat headrest support and remove the front seat headrest.



12. REMOVE FRONT SEAT ARMREST CAP (for Driver Side)


    B130685E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the front seat armrest cap.



13. REMOVE FRONT SEAT ARMREST COVER (for Front Passenger Side)


    B130687E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the front seat armrest cover.



14. REMOVE FRONT SEAT ARMREST ASSEMBLY (for Driver Side)


    B130689
  1. Remove the bolt, the bush and the front seat armrest.



15. REMOVE FRONT SEAT HEADREST SUPPORT


    B332547
  1. Disengage the 3 clamps to separate the front seat side airbag wire harness.



    B130690
  1. Remove the 3 hog rings.



    B332546
  1. Pull out the front seat side airbag wire harness from the front seatback cover.



    B130692
  1. Remove the 2 hog rings.

  1. Unfasten the 2 zippers.



    B210303
  1. Disengage the 2 claws and remove the front seat headrest support.

    HINT:
    Use the same procedure for both sides.



16. REMOVE FRONT SEATBACK ASSEMBLY


    B130696
  1. Using a clip remover, remove the 2 clips.

  1. Remove the 4 hog rings.

  1. Remove the nut.



    B130698
  1. Remove the front seatback.



17. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY


    B328561
  1. Disengage the 2 clamps.

  1. Remove the 2 nuts and front seat side airbag assembly.

    NOTICE:
    1. The nuts must not be reused.
    2. Make sure that the front seat adjuster sub-assembly is not deformed. If it is, replace it with a new one.