UNLOCK WARNING SWITCH > INSTALLATION |
| 1. INSTALL UNLOCK WARNING SWITCH |
![]() |
Install the unlock warning switch onto the steering column bracket upper.
Connect the connector.
| 2. INSTALL KEY INTER LOCK SOLENOID (for Automatic Transmission) |
![]() |
Install the key inter lock solenoid with the 2 screws.
![]() |
Install the clamp onto the steering column bracket upper.
| 3. INSTALL IGNITION SWITCH LOCK CYLINDER AND KEY SET |
![]() |
Make sure that the ignition switch lock cylinder is in the ACC position.
Install the ignition switch lock cylinder.
| 4. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY |

Install the lower instrument panel with the 2 <C> bolts, 2 <E> bolts, 7 <F> bolts and nut <G>.
Engage the clamps and connect the connectors.
| 5. CONNECT PASSENGER AIRBAG CONNECTOR |
![]() |
Connect the passenger airbag connector.
| 6. REMOVE INSTRUMENT PANEL FINISH PANEL END LH |
![]() |
Engage the 3 claws and install the instrument panel finish panel end.
| 7. INSTALL ASSIST GRIP RETAINER RH |
![]() |
Install the assist grip retainer with the 2 bolts.
| 8. INSTALL ASSIST GRIP RETAINER LH |
| 9. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY |
![]() |
Connect the speaker connector.
Insert the 2 hooks into the 2 instrument panel holes and install the front No. 2 speaker with the 2 bolts.
| 10. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Engage the 4 clips and claw and install the instrument panel speaker panel.
| 11. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
| 12. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Engage the 4 clips and 2 claws and install the instrument panel register.
Install the bolt <F> and clip.
![]() |
Engage the 2 claws and install the instrument panel hole cover.
| 13. INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH |
![]() |
Install the connectors to the instrument panel lower finish panel.
Engage the claw and 2 clips and install the instrument panel lower finish panel.
Install screw <A>.
| 14. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Install the glove compartment door assembly with the 3 hinges while holding it horizontal.
![]() |
Slightly flex the upper part of the glove compartment door assembly, and install the glove compartment door assembly.
Install the glove compartment door stoppers onto the glove compartment door.
| 15. INSTALL COMBINATION METER ASSEMBLY |
![]() |
Connect the 2 connectors and the clamp.
![]() |
Install the combination meter assembly with the 4 screws.
| 16. INSTALL INSTRUMENT CLUSTER LOWER FINISH PANEL |
![]() |
Connect the connectors.
Engage the 3 clips and 4 claws and install the instrument cluster lower finish panel.
| 17. INSTALL LOWER INSTRUMENT PANEL LH |
![]() |
Install the lower instrument panel with the 4 <F> bolts.
| 18. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH |
![]() |
Engage the 5 clips and claw and install the lower instrument panel finish panel.
Connect the connector.
Install the 2 <F> bolts.
| 19. INSTALL INSTRUMENT PANEL FINISH PLATE |
![]() |
Install the instrument panel finish plate.
| 20. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Engage the 3 claws and install the hood lock control lever.
| 21. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Engage the 4 clips and 2 claws and install the instrument panel register.
| 22. INSTALL INSTRUMENT LOWER COVER SUB-ASSEMBLY |
![]() |
Engage the 3 clips and 2 claws and install the instrument lower cover.
Install the 2 <F> bolts and 2 clips.
| 23. INSTALL CONSOLE UPPER PANEL NO. 1 GARNISH |
![]() |
Slide the console upper panel garnish toward the front of the vehicle and engage claw B.
Engage the claw and clip and install the console upper panel garnish.
| 24. INSTALL FRONT CONSOLE BOX ASSEMBLY |
![]() |
Engage the 5 claws and install the front console box.
Install the 4 <D> screws.
| 25. INSTALL BOX BOTTOM MAT |
![]() |
Install the box bottom mat.
| 26. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY |
![]() |
Engage the 3 claws and 5 clips and install the console upper rear panel.
| 27. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for 4WD) |
![]() |
Install the shift lever knob.
| 28. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission) |
![]() |
Install the shift lever knob.
| 29. INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY |
![]() |
Slide the parking brake hole cover toward the rear of the vehicle and engage the 2 C claws.
Engage the 4 claws and install the parking brake hole cover.
| 30. INSTALL RADIO RECEIVER ASSEMBLY |
![]() |
Connect the connectors.
Align the 2 bosses of the radio bracket with the hole in the instrument panel and install the radio receiver with the 4 bolts.
| 31. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY |
![]() |
Connect the 3 connectors.
Engage the 4 clips and install the integration control panel assembly.
Install the 2 <H> screws.
| 32. INSTALL INSTRUMENT PANEL GARNISH LH |
![]() |
Engage the 3 clips and install the instrument panel garnish.
Install 2 <H> screws.
| 33. INSTALL INSTRUMENT PANEL GARNISH RH |
![]() |
Engage the 3 clips and install the instrument panel garnish.
Install screw <H>.
| 34. INSTALL FRONT PILLAR GARNISH RH |
Engage the guide and the 2 clips and install the front pillar garnish.
| 35. INSTALL FRONT PILLAR GARNISH LH |
| 36. INSTALL ASSIST GRIP ASSEMBLY |
Install the assist grip with the 2 bolts.
| 37. INSTALL ASSIST GRIP PLUG |
![]() |
| *a | for RH Side |
| *b | for LH Side |
Engage the 2 claws and install the assist grip plug.
| 38. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Install the front door opening trim weatherstrip.
| 39. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
Install the front door opening trim weatherstrip.
| 40. INSTALL COWL SIDE TRIM BOARD RH |
Engage the 2 claws and install the cowl side trim board.
Install the clip.
| 41. INSTALL COWL SIDE TRIM BOARD LH |
| 42. INSTALL FOOTREST CLIP |
![]() |
Engage the 2 claws and install the footrest clip.
| 43. INSTALL FRONT FLOOR FOOTREST |
![]() |
Engage the 2 studs and install the front floor footrest.
| 44. INSTALL FRONT DOOR SCUFF PLATE RH |
![]() |
Engage the 14 claws and install the door scuff plate.
| 45. INSTALL FRONT DOOR SCUFF PLATE LH |
| 46. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 47. INSPECT SRS WARNING LIGHT |