Home › ENGINE › 1GR-FE EMISSION CONTROL › CANISTER

CANISTER > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
  1. Discharge the fuel system pressure (Click here).



2. REMOVE CHARCOAL CANISTER ASSEMBLY


  1. Disconnect the fuel tank vent hose from the charcoal canister assembly.



      A282118
    1. Push the fuel tank vent hose deep inside.
      Text in Illustration 
      V100135
      Push



    2. A282097E01
    3. Pinch portion A, as shown in the illustration.
      Text in Illustration 
      *1
      Nylon Tube
      *2
      O-ring
      *3
      Fuel Tank Vent Hose Retainer
      V100135
      Pull
      V100136
      Pinch

    4. Pull out the fuel tank vent hose from the charcoal canister assembly.

      NOTICE:
      1. Remove any dirt and foreign objects from the fuel tank vent hose connector before performing the work.
      2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tank vent hose connector has the O-ring that seals the pipe.
      3. Perform the work by hand. Do not use any tools.
      4. Do not forcibly bend, twist or turn the nylon tube.
      5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel tank vent hose.
      6. If the fuel tank vent hose connector and pipe are stuck, push and pull them to release.



  1. Disconnect the No. 2 canister outlet hose sub-assembly.



      A288061
    1. Push the No. 2 canister outlet hose sub-assembly deep inside.
      Text in Illustration 
      V100135
      Push



    2. A282098E01
    3. Pinch portion A, as shown in the illustration.
      Text in Illustration 
      *1
      Nylon Tube
      *2
      O-ring
      *3
      No. 2 Canister Outlet Hose Sub-assembly Retainer
      V100135
      Pull
      V100136
      Pinch

    4. Pull out the No. 2 canister outlet hose sub-assembly from the charcoal canister assembly.

      NOTICE:
      1. Remove any dirt and foreign objects from the No. 2 canister outlet hose sub-assembly connector before performing the work.
      2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the No. 2 canister outlet hose sub-assembly connector has the O-ring that seals the pipe.
      3. Perform the work by hand. Do not use any tools.
      4. Do not forcibly bend, twist or turn the nylon tube.
      5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the No. 2 canister outlet hose sub-assembly.
      6. If the No. 2 canister outlet hose sub-assembly and pipe are stuck, push and pull them to release.



    A282115
  1. Disconnect the leak detection pump sub-assembly connector.

  1. Disengage the wire harness clamp and separate the wire harness from the charcoal canister bracket.



    A282116
  1. Loosen the hose clip and disconnect the fuel hose from the No. 1 charcoal canister tube.



    A288068
  1. Remove the 3 bolts and the charcoal canister assembly.



    A288070
  1. Loosen the hose clip and remove the fuel hose from the charcoal canister assembly.



3. REMOVE LEAK DETECTION PUMP SUB-ASSEMBLY
  1. Before removing the leak detection pump sub-assembly, clean the canister by blowing air into it to ensure that the canister is free of foreign matter.

    NOTICE:
    1. Make sure to clean the canister using only air.
    2. Do not use gasoline, thinners or solvents.



    A288064E01
  1. While disengaging the 2 claws as shown in the illustration, push the leak detection pump sub-assembly upwards using a screwdriver to remove it.
    Text in Illustration 
    *1
    Protective Tape

  1. Check if the canister contains foreign matter such as mud or water.

    1. Visually check that the inside of the charcoal canister assembly is free of foreign matter.

    2. Hold the charcoal canister assembly upside down to make sure that the canister is free of foreign matter. If the charcoal canister assembly contains foreign matter, replace the charcoal canister assembly.