Home › BODY ELECTRICAL › WIPER AND WASHER › WIPER AND WASHER SYSTEM

WIPER AND WASHER SYSTEM > Wiper and Washer Switch Circuit

for Preparation Click here


DESCRIPTION

The manual operation signals are sent to the main body ECU.

WIRING DIAGRAM


E152591E01


INSPECTION PROCEDURE

1.CHECK VEHICLE CONDITION
  1. Check whether the rear wiper and washer systems operate normally.

Result:
Condition
Proceed to
Rear wiper and washer systems do not operate.
A
Rear wiper system does not operate.
B
Rear washer system does not operate.
C



B
Go to step 5

C
Go to step 7
A


2.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY
E034825E03
  1. Remove the windshield wiper switch assembly.

  1. Inspect the rear wiper switch.

    1. Measure the resistance.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      2 (E) - 13 (C1R) - 10 (+1R)
      OFF
      10 kΩ or higher
      2 (E) - 13 (C1R)
      LO
      Below 1 Ω
      2 (E) - 10 (+1R)
      HI
      Below 1 Ω

  1. Inspect the rear washer switch.

    1. Measure the resistance.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      2 (E) - 10 (+1R) - 12 (WR)
      OFF
      10 kΩ or higher
      2 (E) - 12 (WR)
      ON (Rear wiper switch in OFF position)
      Below 1 Ω
      2 (E) - 10 (+1R) - 12 (WR)
      ON (Rear wiper switch in ON position)
      Below 1 Ω

  1. Reinstall the the windshield wiper switch assembly.



NG
REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - BODY GROUND)


    E152594E01
  1. Disconnect the E19 windshield wiper switch connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E19-2 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the windshield wiper switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (BATTERY - MAIN BODY ECU)


    B138198E01
  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    1C-2 (SIG) - Body ground
    Ignition switch OFF
    Below 1 V
    1C-2 (SIG) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

5.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY
E034825E04
  1. Remove the windshield wiper switch assembly.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (E) - 13 (C1R) - 10 (+1R)
    Rear wiper switch OFF
    10 kΩ or higher
    2 (E) - 13 (C1R)
    Rear wiper switch LO
    Below 1 Ω
    2 (E) - 10 (+1R)
    Rear wiper switch HI
    Below 1 Ω

  1. Reinstall the the windshield wiper switch assembly.



NG
REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - MAIN BODY ECU, BODY GROUND)
B136062E01
  1. Disconnect the E8 main body ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-9 (WRIN) - E8-10 (WRLO) - Body ground
    Rear wiper switch OFF
    10 kΩ or higher
    E8-9 (WRIN) - Body ground
    Rear wiper switch LO
    Below 1 Ω
    E8-10 (WRLO) - Body ground
    Rear wiper switch HI
    Below 1 Ω

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

7.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY
E034825E05
  1. Remove the windshield wiper switch assembly.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (E) - 10 (+1R) - 12 (WR)
    Rear washer switch OFF
    10 kΩ or higher
    2 (E) - 12 (WR)
    Rear washer switch ON (Rear wiper switch OFF position side)
    Below 1 Ω
    2 (E) - 10 (+1R) - 12 (WR)
    Rear washer switch ON (Rear wiper switch ON position side)
    Below 1 Ω

  1. Reinstall the the windshield wiper switch assembly.



NG
REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - MAIN BODY ECU, BODY GROUND)
B136063E01
  1. Disconnect the E7 main body ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E7-1 (RWSW) - Body ground
    Rear washer switch OFF
    10 kΩ or higher
    E7-1 (RWSW) - Body ground
    Rear washer switch ON (Rear wiper switch in ON position)
    Below 1 Ω
    E7-1 (RWSW) - Body ground
    Rear washer switch ON (Rear wiper switch in OFF position)
    Below 1 Ω

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)