Home › BODY ELECTRICAL › OTHER SYSTEM › VOLTAGE INVERTER

VOLTAGE INVERTER > INSTALLATION

for Preparation Click here



1. INSTALL VOLTAGE INVERTER ASSEMBLY
  1. Engage the guide and install the voltage inverter assembly with the 3 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Install the ground wire with the bolt.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Engage the clamp and connect the 2 connectors.



2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
  1. Engage the 6 clips and the 8 claws and install the deck trim side panel.

  1. Install the 3 screws.

  1. Install the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



3. INSTALL REAR DECK TRIM COVER


    B138600
  1. Connect the power outlet connector.



    B135130
  1. Engage the 8 claws and install the rear deck trim cover.



4. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH
  1. Install the anchor plate with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Make sure that the anchor plate rotates smoothly.



5. INSTALL LAP BELT OUTER ANCHOR COVER

HINT:
Use the same procedure for both sides.

  1. Engage the 3 claws and install the lap belt outer anchor cover.



6. INSTALL QUARTER TRIM POCKET (w/o Amplifier Box Speaker Assembly)


    B130613
  1. Engage the 6 claws and install the quarter trim pocket.



7. INSTALL SIDE TRIM COVER (w/o Amplifier Box Speaker Assembly)


    B130612
  1. Engage the 8 claws and install the side trim cover.



8. INSTALL QUARTER TRIM POCKET TRAY (w/o Amplifier Box Speaker Assembly)


    B130611
  1. Engage the 7 claws and install the quarter trim pocket tray.



9. INSTALL PACKAGE HOLDER NET HOOK (w/o Amplifier Box Speaker Assembly)

HINT:
Use the same procedure to install all the package holder net hooks.

  1. Install the package holder net hook with the bolt.

    Torque:
    8.1 N*m{ 83 kgf*cm , 72 in.*lbf }



10. INSTALL AMPLIFIER BOX SPEAKER ASSEMBLY (w/ Amplifier Box Speaker Assembly)


    B134990
  1. Install the amplifier box speaker with the 4 screws.

    Torque:
    8.1 N*m{ 85 kgf*cm , 72 in.*lbf }

  1. Connect the speaker connector.



11. INSTALL SPEAKER MOUNTING COVER (w/ Amplifier Box Speaker Assembly)


    B134991
  1. Engage the 8 clips and install the speaker mounting cover.



12. INSTALL DECK SIDE GARNISH (w/ Amplifier Box Speaker Assembly)


    B134992
  1. Engage the 6 claws and install the deck side garnish.



13. INSTALL REAR DOOR SCUFF PLATE RH


    B130598
  1. Engage the 6 claws and install the access door scuff plate.



14. INSTALL FRONT DOOR SCUFF PLATE RH


    B130597
  1. Engage the 14 claws and install the door scuff plate.



15. INSTALL REAR FLOOR MAT ASSEMBLY


    B130594
  1. Install the rear floor mat with the 2 clips.



16. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY


B179163E01

HINT:
Use the same procedure for both sides.

  1. Install the luggage hold belt striker with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Install the cap.



17. INSTALL REAR FLOOR MAT SUPPORT PLATE


    B130593
  1. Engage the 11 claws and install the rear floor mat support plate.



    B130592
  1. Tighten the 5 screws.



18. INSTALL REAR FLOOR BOARD


    B135075
  1. Engage the clip and claw and install the rear floor board.



    B135074E02
  1. Install the luggage hold belt striker with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    HINT:
    Use the same procedure for both sides.



19. INSTALL REAR SEATBACK ASSEMBLY
(Click here)