Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C146E    Open in ABS Solenoid Relay Circuit

DTC    C146F    Short in ABS Solenoid Relay Circuit

for Preparation Click here


DESCRIPTION

The solenoid relay supplies power to the ABS solenoid and TRAC solenoid.
After the ignition switch is turned to ON, the vehicle speed has reached 6 km/h (4 mph) and the solenoid is determined to be normal by the initial check self- diagnosis, the relay switches on. If any open or short circuits are detected, the relay switches off.
These DTCs may be set if the voltage supply to the solenoid relay (+BS) falls below the DTC detection threshold due to the battery or generator outputs being insufficient.

DTC Code
DTC Detection Condition
Trouble Area
C146E
When either of following conditions detected:
  1. Both of following conditions continue for at least 0.2 seconds.
    1. IG voltage between 9.5 V and 17 V.
    2. Relay contact open when relay ON
  2. Both of following conditions continue for at least 0.2 seconds.
    1. IG voltage 9.5 V or less when relay ON.
    2. Relay contact remains open.
  1. ABS SOL fuse
  2. +BS terminal circuit
  3. Master cylinder solenoid (skid control ECU)
C146F
Following condition continues for at least 0.2 seconds.
  1. Relay contact closed immediately after turning IG switch to ON when relay OFF.
Master cylinder solenoid (skid control ECU)

WIRING DIAGRAM


C230326E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT SKID CONTROL ECU (+BS TERMINAL)


    C214161E50
  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-31 (+BS) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT SKID CONTROL ECU (GND TERMINAL)


    C124799E53
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A4-32 (GND2) - Body ground
    Always
    Below 1 Ω
    A5-4 (GND3) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.RECONFIRM DTC

HINT:
These codes are stored when a problem is detected in the master cylinder solenoid.
The solenoid relay is in the master cylinder solenoid. Therefore, solenoid relay circuit inspections and relay unit inspections cannot be performed. Be sure to check if any DTC is output before replacing the master cylinder solenoid.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.

  1. Check if the same DTCs are output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)